Modeling and Experimental Verification of a Hybrid Energy Harvester Using Piezoelectric and Electromagnetic Technologies

2012 ◽  
Vol 569 ◽  
pp. 529-532 ◽  
Author(s):  
Zhen Long Xu ◽  
Xiao Xi Wang ◽  
Xiao Biao Shan ◽  
Tao Xie
Keyword(s):  
Output Power ◽  
Energy Harvester ◽  
Maximum Output Power ◽  
Experimental Results ◽  
Maximum Output ◽  
Hybrid Energy ◽  
Energy Harvesters ◽  
Hybrid Energy Harvester ◽  
Theoretical Results ◽  
Good Agreement

This paper presents a hybrid energy harvester using piezoelectric (PZT) and electromagnetic (EM) technologies. A mathematical model of the output power for this generator was developed. Experiments were carried out to verify the numerical analysis. The theoretical results were in good agreement with the experimental results. The experimental results showed that the maximum output power of the separate PZT and EM energy harvesters were 0.667 mW and 0.32 mW, while that of the hybrid harvester was 0.845 mW under the vibration acceleration of 9.8 m/s2 at 66 Hz. It shows that the hybrid energy harvester can effectively increase the output power.

scholarly journals Study of the Properties of a Hybrid Piezoelectric and Electromagnetic Energy Harvester for a Civil Engineering Low-Frequency Sloshing Environment

Energies ◽  
2021 ◽  
Vol 14 (2) ◽  
pp. 391
Author(s):  
Nan Wu ◽  
Yuncheng He ◽  
Jiyang Fu ◽  
Peng Liao
Keyword(s):  
Output Power ◽  
Energy Harvester ◽  
Civil Engineering ◽  
Maximum Output Power ◽  
Low Frequency ◽  
Electromagnetic Energy ◽  
Maximum Output ◽  
Piezoelectric Film ◽  
Hybrid Energy ◽  
Level Height

In this paper a novel hybrid piezoelectric and electromagnetic energy harvester for civil engineering low-frequency sloshing environment is reported. The architecture, fabrication and characterization of the harvester are discussed. The hybrid energy harvester is composed of a permanent magnet, copper coil, and PVDF(polyvinylidene difluoride) piezoelectric film, and the upper U-tube device containing a cylindrical fluid barrier is connected to the foundation support plate by a hinge and spring. The two primary means of energy collection were through the vortex street, which alternately impacted the PVDF piezoelectric film through fluid shedding, and the electromotive force (EMF) induced by changes in the magnetic field position in the conducting coil. Experimentally, the maximum output power of the piezoelectric transformer of the hybrid energy harvester was 2.47 μW (circuit load 270 kΩ; liquid level height 80 mm); and the maximum output power of the electromagnetic generator was 2.72 μW (circuit load 470 kΩ; liquid level height 60 mm). The low-frequency sloshing energy collected by this energy harvester can drive microsensors for civil engineering monitoring.

scholarly journals Topology Selection and Parametric Design of Electromagnetic Vibration Energy Harvesters by Combining FEA-in-the-Loop and Analytical Approaches

Energies ◽  
2020 ◽  
Vol 13 (3) ◽  
pp. 627 ◽  
Author(s):  
Seong-yeol Yoo ◽  
Young-Woo Park ◽  
Myounggyu Noh
Keyword(s):  
Output Power ◽  
Permanent Magnets ◽  
Energy Harvester ◽  
Maximum Output Power ◽  
Electromagnetic Energy ◽  
Vibration Energy ◽  
Maximum Output ◽  
Primary Concern ◽  
Energy Harvesters ◽  
Analytical Approaches

Electromagnetic energy harvesters have been used to capture low-frequency vibration energy of large machines such as diesel generators. The structure of an electromagnetic energy harvester is either planar or tubular. Past research efforts focus on optimally designing each structure separately. An objective comparison between the two structures is necessary in order to decide which structure is advantageous. When comparing the structures, the design variations such as magnetization patterns and the use of yokes must also be considered. In this study, extensive comparisons are made covering all possible topologies of an electromagnetic energy harvester. A bench mark harvester is defined and the parameters that produce maximum output power are identified for each topology. It is found that the tubular harvesters generally produce larger output power than the planar counterparts. The largest output power is generated by the tubular harvester with a Halbach magnetization pattern (94.7 mW). The second best is the tubular harvester with axial magnetization pattern (79.1 mW) when moving yokes are inserted between permanent magnets for flux concentration. When cost is of primary concern, the tubular harvester with axial pattern may become a best option.

scholarly journals Modeling, Validation, and Performance of Two Tandem Cylinder Piezoelectric Energy Harvesters in Water Flow

Micromachines ◽  
2021 ◽  
Vol 12 (8) ◽  
pp. 872
Author(s):  
Rujun Song ◽  
Chengwei Hou ◽  
Chongqiu Yang ◽  
Xianhai Yang ◽  
Qianjian Guo ◽  
...  
Keyword(s):  
Energy Harvesting ◽  
Output Power ◽  
Water Flow ◽  
Energy Harvester ◽  
Beat Frequency ◽  
Maximum Output Power ◽  
Total Output ◽  
Maximum Output ◽  
Energy Harvesters ◽  
Piezoelectric Energy

This paper studies a novel enhanced energy-harvesting method to harvest water flow-induced vibration with a tandem arrangement of two piezoelectric energy harvesters (PEHs) in the direction of flowing water, through simulation modeling and experimental validation. A mathematical model is established by two individual-equivalent single-degree-of-freedom models, coupled with the hydrodynamic force obtained by computational fluid dynamics. Through the simulation analysis, the variation rules of vibration frequency, vibration amplitude, power generation and the distribution of flow field are obtained. And experimental tests are performed to verify the numerical calculation. The experimental and simulation results show that the upstream piezoelectric energy harvester (UPEH) is excited by the vortex-induced vibration, and the maximum value of performance is achieved when the UPEH and the vibration are resonant. As the vortex falls off from the UPEH, the downstream piezoelectric energy harvester (DPEH) generates a responsive beat frequency vibration. Energy-harvesting performance of the DPEH is better than that of the UPEH, especially at high speed flows. The maximum output power of the DPEH (371.7 μW) is 2.56 times of that of the UPEH (145.4 μW), at a specific spacing between the UPEN and the DPEH. Thereupon, the total output power of the two tandem piezoelectric energy harvester systems is significantly greater than that of the common single PEH, which provides a good foreground for further exploration of multiple piezoelectric energy harvesters system.

scholarly journals Power Density Improvement of Piezoelectric Energy Harvesters via a Novel Hybridization Scheme with Electromagnetic Transduction

Micromachines ◽  
2021 ◽  
Vol 12 (7) ◽  
pp. 803
Author(s):  
Zhongjie Li ◽  
Chuanfu Xin ◽  
Yan Peng ◽  
Min Wang ◽  
Jun Luo ◽  
...  
Keyword(s):  
Power Density ◽  
Output Power ◽  
Energy Harvester ◽  
Hybrid Energy ◽  
Energy Harvesters ◽  
Piezoelectric Patch ◽  
Piezoelectric Energy ◽  
Electromagnetic Transduction ◽  
Self Powered ◽  
Power Densities

A novel hybridization scheme is proposed with electromagnetic transduction to improve the power density of piezoelectric energy harvester (PEH) in this paper. Based on the basic cantilever piezoelectric energy harvester (BC-PEH) composed of a mass block, a piezoelectric patch, and a cantilever beam, we replaced the mass block by a magnet array and added a coil array to form the hybrid energy harvester. To enhance the output power of the electromagnetic energy harvester (EMEH), we utilized an alternating magnet array. Then, to compare the power density of the hybrid harvester and BC-PEH, the experiments of output power were conducted. According to the experimental results, the power densities of the hybrid harvester and BC-PEH are, respectively, 3.53 mW/cm3 and 5.14 μW/cm3 under the conditions of 18.6 Hz and 0.3 g. Therefore, the power density of the hybrid harvester is 686 times as high as that of the BC-PEH, which verified the power density improvement of PEH via a hybridization scheme with EMEH. Additionally, the hybrid harvester exhibits better performance for charging capacitors, such as charging a 2.2 mF capacitor to 8 V within 17 s. It is of great significance to further develop self-powered devices.

Modelling of Mechanical Nonlinearity in an Electromagnetic Vibration Energy Harvester Using a Forced Duffing Equation

2012 ◽  
Author(s):  
S. D. Moss ◽  
L. A. Vandewater ◽  
S. C. Galea
Keyword(s):  
Output Power ◽  
Energy Harvester ◽  
Duffing Oscillator ◽  
Maximum Output Power ◽  
Vibration Energy ◽  
Maximum Output ◽  
Vibration Energy Harvesting ◽  
Vibration Energy Harvester ◽  
Homotopy Analysis ◽  
Wire Coil

This work reports on the modelling and experimental validation of a bi-axial vibration energy harvesting approach that uses a permanent-magnet/ball-bearing arrangement and a wire-coil transducer. The harvester’s behaviour is modelled using a forced Duffing oscillator, and the primary first order steady state resonant solutions are found using the homotopy analysis method (or HAM). Solutions found are shown to compare well with measured bearing displacements and harvested output power, and are used to predict the wideband frequency response of this type of vibration energy harvester. A prototype harvesting arrangement produced a maximum output power of 12.9 mW from a 12 Hz, 500 milli-g (or 4.9 m/s2) rms excitation.

scholarly journals Bidirectional Piezoelectric Energy Harvester

Sensors ◽  
2019 ◽  
Vol 19 (18) ◽  
pp. 3845 ◽  
Author(s):  
Andrius Čeponis ◽  
Dalius Mažeika ◽  
Artūras Kilikevičius
Keyword(s):  
Output Power ◽  
Energy Harvester ◽  
Maximum Output Power ◽  
Geometrical Parameters ◽  
Maximum Output ◽  
Electrical Characteristics ◽  
Harmonic Vibrations ◽  
Piezoelectric Energy ◽  
Out Of Plane ◽  
Bending Modes

This paper represents a numerical and experimental investigation of the bidirectional piezoelectric energy harvester. The harvester can harvest energy from the vibrating base in two perpendicular directions. The introduced harvester consists of two cantilevers that are connected by a particular angle and two seismic masses. The first mass is placed at a free end of the harvester while the second mass is fixed at the joining point of the cantilevers. The piezoelectric energy harvester employs the first and the second out of plane bending modes. The numerical investigation was carried out to obtain optimal geometrical parameters and to calculate the mechanical and electrical characteristics of the harvester. The energy harvester can provide stable output power during harmonic and impact-based excitation in two directions. The results of the investigations showed that energy harvester provides a maximum output power of 16.85 µW and 15.9 4 µW when the base has harmonic vibrations in y and z directions, respectively. Maximum output of 4.059 nW/N and 3.1 nW/N in y and z directions were obtained in case of impact based excitation

scholarly journals Design and Analysis of a Magnetically Coupled Multi-Frequency Hybrid Energy Harvester

Sensors ◽  
2019 ◽  
Vol 19 (14) ◽  
pp. 3203 ◽  
Author(s):  
Zhenlong Xu ◽  
Hong Yang ◽  
Hao Zhang ◽  
Huawei Ci ◽  
Maoying Zhou ◽  
...  
Keyword(s):  
Output Power ◽  
Electromechanical Coupling ◽  
Energy Harvester ◽  
Hybrid Energy ◽  
Energy Harvesters ◽  
Peak Output Power ◽  
Piezoelectric Energy ◽  
Operating Bandwidth ◽  
Frequency Sweep Test ◽  
Hybrid Energy Harvesting

The approach to improve the output power of piezoelectric energy harvester is one of the current research hotspots. In the case where some sources have two or more discrete vibration frequencies, this paper proposed three types of magnetically coupled multi-frequency hybrid energy harvesters (MHEHs) to capture vibration energy composed of two discrete frequencies. Electromechanical coupling models were established to analyze the magnetic forces, and to evaluate the power generation characteristics, which were verified by the experimental test. The optimal structure was selected through the comparison. With 2 m/s2 excitation acceleration, the optimal peak output power was 2.96 mW at 23.6 Hz and 4.76 mW at 32.8 Hz, respectively. The superiority of hybrid energy harvesting mechanism was demonstrated. The influences of initial center-to-center distances between two magnets and length of cantilever beam on output power were also studied. At last, the frequency sweep test was conducted. Both theoretical and experimental analyses indicated that the proposed MHEH produced more electric power over a larger operating bandwidth.

Complex Impedance Matching for Power Improvement of a Circular Piezoelectric Energy Harvester

2011 ◽  
Vol 148-149 ◽  
pp. 169-172 ◽  
Author(s):  
Hong Yan Wang ◽  
Xiao Biao Shan ◽  
Tao Xie
Keyword(s):  
Output Power ◽  
Power Output ◽  
Energy Harvester ◽  
Impedance Matching ◽  
Maximum Output Power ◽  
Complex Impedance ◽  
Complex Conjugate ◽  
Maximum Output ◽  
Piezoelectric Energy ◽  
Matching Load

The impedance matching and the optimization of power from a circular piezoelectric energy harvester with a central-attached mass are studied. A finite element model is constructed to analyze the electrical equivalent impedance of the circular piezoelectric energy harvester. Furthermore, the complex conjugate matching load is used to extract the maximum output power of the energy harvester. The power output from complex conjugate matching load is compared with the power output from the resistive matching load and a constant resistance, separately. The results suggest that the complex conjugate matching can result in a significant increase of the output power for all frequencies. The effective bandwidth of the piezoelectric energy harvester is extended significantly.

Sign in / Sign up

Export Citation Format

Share Document