scholarly journals Design and Analysis of a Magnetically Coupled Multi-Frequency Hybrid Energy Harvester

Sensors ◽  
2019 ◽  
Vol 19 (14) ◽  
pp. 3203 ◽  
Author(s):  
Zhenlong Xu ◽  
Hong Yang ◽  
Hao Zhang ◽  
Huawei Ci ◽  
Maoying Zhou ◽  
...  
Keyword(s):  
Output Power ◽  
Electromechanical Coupling ◽  
Energy Harvester ◽  
Hybrid Energy ◽  
Energy Harvesters ◽  
Peak Output Power ◽  
Piezoelectric Energy ◽  
Operating Bandwidth ◽  
Frequency Sweep Test ◽  
Hybrid Energy Harvesting

The approach to improve the output power of piezoelectric energy harvester is one of the current research hotspots. In the case where some sources have two or more discrete vibration frequencies, this paper proposed three types of magnetically coupled multi-frequency hybrid energy harvesters (MHEHs) to capture vibration energy composed of two discrete frequencies. Electromechanical coupling models were established to analyze the magnetic forces, and to evaluate the power generation characteristics, which were verified by the experimental test. The optimal structure was selected through the comparison. With 2 m/s2 excitation acceleration, the optimal peak output power was 2.96 mW at 23.6 Hz and 4.76 mW at 32.8 Hz, respectively. The superiority of hybrid energy harvesting mechanism was demonstrated. The influences of initial center-to-center distances between two magnets and length of cantilever beam on output power were also studied. At last, the frequency sweep test was conducted. Both theoretical and experimental analyses indicated that the proposed MHEH produced more electric power over a larger operating bandwidth.

scholarly journals Power Density Improvement of Piezoelectric Energy Harvesters via a Novel Hybridization Scheme with Electromagnetic Transduction

Micromachines ◽  
2021 ◽  
Vol 12 (7) ◽  
pp. 803
Author(s):  
Zhongjie Li ◽  
Chuanfu Xin ◽  
Yan Peng ◽  
Min Wang ◽  
Jun Luo ◽  
...  
Keyword(s):  
Power Density ◽  
Output Power ◽  
Energy Harvester ◽  
Hybrid Energy ◽  
Energy Harvesters ◽  
Piezoelectric Patch ◽  
Piezoelectric Energy ◽  
Electromagnetic Transduction ◽  
Self Powered ◽  
Power Densities

A novel hybridization scheme is proposed with electromagnetic transduction to improve the power density of piezoelectric energy harvester (PEH) in this paper. Based on the basic cantilever piezoelectric energy harvester (BC-PEH) composed of a mass block, a piezoelectric patch, and a cantilever beam, we replaced the mass block by a magnet array and added a coil array to form the hybrid energy harvester. To enhance the output power of the electromagnetic energy harvester (EMEH), we utilized an alternating magnet array. Then, to compare the power density of the hybrid harvester and BC-PEH, the experiments of output power were conducted. According to the experimental results, the power densities of the hybrid harvester and BC-PEH are, respectively, 3.53 mW/cm3 and 5.14 μW/cm3 under the conditions of 18.6 Hz and 0.3 g. Therefore, the power density of the hybrid harvester is 686 times as high as that of the BC-PEH, which verified the power density improvement of PEH via a hybridization scheme with EMEH. Additionally, the hybrid harvester exhibits better performance for charging capacitors, such as charging a 2.2 mF capacitor to 8 V within 17 s. It is of great significance to further develop self-powered devices.

Performance analysis of a lever piezoelectric energy harvester for roadway applications

2021 ◽  
pp. 1045389X2110014
Author(s):  
Guangya Ding ◽  
Hongjun Luo ◽  
Jun Wang ◽  
Guohui Yuan
Keyword(s):  
Output Power ◽  
Energy Harvester ◽  
Open Circuit ◽  
Traffic Load ◽  
Energy Harvesters ◽  
Speed Sensor ◽  
Piezoelectric Energy ◽  
Optimal Load ◽  
Self Powered ◽  
Output Characteristics

A novel lever piezoelectric energy harvester (LPEH) was designed for installation in an actual roadway for energy harvesting. The model incorporates a lever module that amplifies the applied traffic load and transmits it to the piezoelectric ceramic. To observe the piezoelectric growth benefits of the optimized LPEH structure, the output characteristics and durability of two energy harvesters, the LPEH and a piezoelectric energy harvester (PEH) without a lever, were measured and compared by carrying out piezoelectric performance tests and traffic model experiments. Under the same loading condition, the open circuit voltages of the LPEH and PEH were 20.6 and 11.7 V, respectively, which represents a 76% voltage increase for the LPEH compared to the PEH. The output power of the LPEH was 21.51 mW at the optimal load, which was three times higher than that of the PEH (7.45 mW). The output power was linearly dependent on frequency and load, implying the potential application of the module as a self-powered speed sensor. When tested during 300,000 loading cycles, the LPEH still exhibited stable structural performance and durability.

scholarly journals Piezoelectric Performance of a Symmetrical Ring-Shaped Piezoelectric Energy Harvester Using PZT-5H under a Temperature Gradient

Micromachines ◽  
2020 ◽  
Vol 11 (7) ◽  
pp. 640
Author(s):  
Nannan Zhou ◽  
Rongqi Li ◽  
Hongrui Ao ◽  
Chuanbing Zhang ◽  
Hongyuan Jiang
Keyword(s):  
Growth Rate ◽  
Output Power ◽  
Output Voltage ◽  
Electromechanical Coupling ◽  
Energy Harvester ◽  
Rapid Development ◽  
Coupling Model ◽  
Output Performance ◽  
Piezoelectric Energy ◽  
Changing Trend

With the rapid development of microelectronics technology, low-power electronic sensors have been widely applied in many fields, such as Internet of Things, aerospace, and so on. In this paper, a symmetrical ring-shaped piezoelectric energy harvester (SR-PEH) is designed to provide energy for the sensor to detect the ambient temperature. The finite element method is used by utilizing software COMSOL 5.4, and the electromechanical coupling model of the piezoelectric cantilever is established. The output performance equations are proposed; the microelectromechanical system (MEMS) integration process of the SR-PEH, circuit, and sensor is stated; and the changing trend of the output power density is explained from an energy perspective. In the logarithmic coordinate system, the results indicate that the output voltage and output power are approximately linear with the temperature when the resistance is constant. In addition, the growth rate of the output voltage and output power decreases with an increase of resistance under the condition of constant temperature. In addition, with an increase of temperature, the growth rate of the output power is faster than that of the output voltage. Furthermore, resistance has a more dramatic effect on the output voltage, whereas temperature has a more significant effect on the output power. More importantly, the comparison with the conventional cantilever-shaped piezoelectric energy harvester (CC-PEH) shows that the SR-PEH can improve the output performance and broaden the frequency band.

Equivalent impedance and power analysis of monostable piezoelectric energy harvesters

2020 ◽  
Vol 31 (14) ◽  
pp. 1697-1715
Author(s):  
Chunbo Lan ◽  
Yabin Liao ◽  
Guobiao Hu ◽  
Lihua Tang
Keyword(s):  
Equivalent Circuit ◽  
Electromechanical Coupling ◽  
Energy Harvester ◽  
Performance Enhancement ◽  
Damping Ratio ◽  
Power Performance ◽  
Closed Form Solutions ◽  
Energy Harvesters ◽  
Piezoelectric Energy ◽  
Power Limit

Nonlinearity has been successfully introduced into piezoelectric energy harvesting for power performance enhancement and bandwidth enlargement. While a great deal of emphasis has been placed by researchers on the structural design and broadband effect, this article is motivated to investigate the maximum power of a representative type of nonlinear piezoelectric energy harvesters, that is, monostable piezoelectric energy harvester. An equivalent circuit is proposed to analytically study and explain system behaviors. The effect of nonlinearity is modeled as a nonlinear stiffness element mechanically and a nonlinear capacitive element electrically. Facilitated by the equivalent circuit, closed-form solutions of power limit and critical electromechanical coupling, that is, minimum coupling to reach the power limit, of monostable piezoelectric energy harvesters are obtained, which are used for a clear explanation of the system behavior. Several important conclusions have been drawn from the analytical analysis and validated by numerical simulations. First, given the same level of external excitation, the monostable piezoelectric energy harvester and its linear counterpart are subjected to the same power limit. Second, while the critical coupling of linear piezoelectric energy harvesters depends on the mechanical damping ratio only, it also depends on the vibration excitation and magnetic field for monostable piezoelectric energy harvesters, which can be used to adjust the power performance of the system.

Fabrication and analytical modeling of transverse mode piezoelectric energy harvesters

2012 ◽  
Vol 1397 ◽  
Author(s):  
Seon-Bae Kim ◽  
Jung-Hyun Park ◽  
Seung-Hyun Kim ◽  
Hosang Ahn ◽  
H. Clyde Wikle ◽  
...  
Keyword(s):  
Output Power ◽  
Analytical Modeling ◽  
Energy Harvester ◽  
Power Conversion ◽  
Transverse Mode ◽  
Modified Model ◽  
Energy Harvesters ◽  
Piezoelectric Energy ◽  
Interdigital Electrodes ◽  
Piezoelectric Cantilever

ABSTRACTA transverse (d33) mode piezoelectric cantilever was fabricated for energy harvesting. Various dimensions of interdigital electrodes (IDE) were deposited on a piezoelectric layer to examine the effects of electrode design on the performance of energy harvesters. Modeling was performed to calculate the output power of the devices. The estimation was based on Roundy’s analytical modeling derived for a d31 mode piezoelectric energy harvester (PEH). In order to apply the Roundy’s model to d33 mode PEH, the IDE configuration was converted to the area of top and bottom electrodes (TBE). The power conversion in d33 mode PEH was commonly estimated by the product of piezoelectric layer’s thickness and finger electrode’s length. In addition, the spacing between fingers was regarded as gap between top and bottom electrodes. However, the output power in a transverse mode PEH increases continuously with the increase of finger spacing, which does not correspond to experimental results. In this research, the dimension of IDE was converted to that of TBE using conformal mapping, and variation of power of PEH was remodeled. The modified model suggests that the maximum power in a transverse mode PEH is obtained when the finger spacing is identical with effective finger spacing. The output power then decreases when finger spacing is larger than effective finger spacing. The decrease of efficiency may result from insufficient degree of poling and increased charged defect with increasing finger spacing.

scholarly journals Bandwidth Broadening of Piezoelectric Energy Harvesters Using Arrays of a Proposed Piezoelectric Cantilever Structure

Micromachines ◽  
2021 ◽  
Vol 12 (8) ◽  
pp. 973
Author(s):  
Marwa S. Salem ◽  
Shimaa Ahmed ◽  
Ahmed Shaker ◽  
Mohammad T. Alshammari ◽  
Kawther A. Al-Dhlan ◽  
...  
Keyword(s):  
Resonant Frequency ◽  
Piezoelectric Material ◽  
Output Power ◽  
Energy Harvester ◽  
Vibration Source ◽  
Energy Harvesters ◽  
Piezoelectric Energy ◽  
Narrow Bandwidth ◽  
Cantilever Structure ◽  
Bandwidth Broadening

One of the most important challenges in the design of the piezoelectric energy harvester is its narrow bandwidth. Most of the input vibration sources are exposed to frequency variation during their operation. The piezoelectric energy harvester’s narrow bandwidth makes it difficult for the harvester to track the variations of the input vibration source frequency. Thus, the harvester’s output power and overall performance is expected to decline from the designed value. This current study aims to solve the problem of the piezoelectric energy harvester’s narrow bandwidth. The main objective is to achieve bandwidth broadening which is carried out by segmenting the piezoelectric material of the energy harvester into n segments; where n could be more than one. Three arrays with two, four, and six beams are shaped with two piezoelectric segments. The effect of changing the length of the piezoelectric material segment on the resonant frequency, output power, and bandwidth, as well as the frequency response is investigated. The proposed piezoelectric energy harvesters were implemented utilizing a finite element method (FEM) simulation in a MATLAB environment. The results show that increasing the number of array beams increases the output power and bandwidth. For the three-beam arrays, at n equals 2, 6 mW output power and a 9 Hz bandwidth were obtained. Moreover, the bandwidth of such arrays covered around 5% deviation from its resonant frequency. All structures were designed to operate as a steel wheel safety sensor which could be used in train tracks.

Theoretical modeling and analysis of a 2-degree-of-freedom hybrid piezoelectric–electromagnetic vibration energy harvester with a driven beam

2018 ◽  
Vol 29 (11) ◽  
pp. 2465-2476 ◽  
Author(s):  
Dan Zhao ◽  
Shaogang Liu ◽  
Qingtao Xu ◽  
Wenyi Sun ◽  
Tao Wang ◽  
...  
Keyword(s):  
Energy Harvesting ◽  
Output Power ◽  
Energy Harvester ◽  
Degree Of Freedom ◽  
Energy Output ◽  
Vibration Energy ◽  
Vibration Energy Harvester ◽  
Piezoelectric Energy ◽  
Electromagnetic Vibration ◽  
Operating Bandwidth

In the article, a novel 2-degree-of-freedom hybrid piecewise-linear piezoelectric–electromagnetic vibration energy harvester is presented to achieve better energy harvesting efficiency. The harvester consists of a primary piezoelectric energy harvesting device to which an electromagnetic mechanism is coupled to improve the integral energy output, and a driven beam is mounted to broaden the operating bandwidth by inducing nonlinearity. Considering the piezoelectric–electromagnetic coupling characteristics and the nonlinear factors, dynamic equations of the system are established. Expressions of the output power are deduced though averaging method. Characteristic parameters are analyzed theoretically, including the piezoelectric parameters, electromagnetic parameters, and the piecewise-linearity. Frequency sweep excitation test is conducted on the setup at an excitation acceleration of 0.3 g and results demonstrate that two resonant regions are obtained with the peak output power of 5.4 and 6.49 mW, respectively, and the operating bandwidth is increased by 8 Hz. Moreover, though adjusting the stiffness of the driven beam k3 and the gap between the primary beam and the driven beam d, the performance of the harvester can be further optimized.

Flexoelectric Energy Harvesting of Circular Rings

2013 ◽  
Author(s):  
X. F. Zhang ◽  
S. D. Hu ◽  
H. S. Tzou
Keyword(s):  
Energy Harvesting ◽  
Output Power ◽  
Strain Gradient ◽  
Electromechanical Coupling ◽  
Energy Harvester ◽  
Excitation Frequency ◽  
Design Parameters ◽  
Equivalent Resistance ◽  
Flexoelectric Effect ◽  
Piezoelectric Energy

Flexoelectricity, the electromechanical coupling of the polarization response and strain gradient, occurs in solid crystalline dielectrics of any symmetry or asymmetric crystals. Different from the piezoelectric energy harvester, an energy harvester based on the direct flexoelectric effect is designed in this study. The energy harvester consists of an elastic ring and a flexoelectric patch laminated on its outer surface. Due to the direct flexoelectric effect, the electric energy induced by the strain gradient of the flexoelectric patch is harvested to power the electric device when the ring is subjected to mechanical excitations. Electromechanical coupling equation of the flexoelectric energy harvesting system in close-loop circuit condition is derived. In this study, dynamic response, output power across the external resistor and energy harvesting results are evaluated when the ring is excited by a harmonic point loading. The output power is a function of the external excitation frequency, the external equivalent resistance, the flexoelectric patch’s thickness and other design parameters. Case studies of those parameters for the flexoelectric energy harvester are presented to optimize the output power. Results show that the optimal excitation frequency is equal to the natural frequency for each mode, and the optimal equivalent resistance is dependent of the equivalent capacitance of the flexoelectric patch and the excitation frequency. Since the output power of the flexoelectric energy harvester is similar to that of the piezoelectric energy harvester, comparison of the two harvesters is also discussed. With all the optimal conditions discussed, it can supply a design principle in the engineering applications.

Modeling and Experimental Verification of a Hybrid Energy Harvester Using Piezoelectric and Electromagnetic Technologies

2012 ◽  
Vol 569 ◽  
pp. 529-532 ◽  
Author(s):  
Zhen Long Xu ◽  
Xiao Xi Wang ◽  
Xiao Biao Shan ◽  
Tao Xie
Keyword(s):  
Output Power ◽  
Energy Harvester ◽  
Maximum Output Power ◽  
Experimental Results ◽  
Maximum Output ◽  
Hybrid Energy ◽  
Energy Harvesters ◽  
Hybrid Energy Harvester ◽  
Theoretical Results ◽  
Good Agreement

This paper presents a hybrid energy harvester using piezoelectric (PZT) and electromagnetic (EM) technologies. A mathematical model of the output power for this generator was developed. Experiments were carried out to verify the numerical analysis. The theoretical results were in good agreement with the experimental results. The experimental results showed that the maximum output power of the separate PZT and EM energy harvesters were 0.667 mW and 0.32 mW, while that of the hybrid harvester was 0.845 mW under the vibration acceleration of 9.8 m/s2 at 66 Hz. It shows that the hybrid energy harvester can effectively increase the output power.

Performance of a Piezoelectric Bimorph Harvester with Variable Width

2007 ◽  
Vol 23 (3) ◽  
pp. 197-202 ◽  
Author(s):  
H. P. Hu ◽  
Z. J. Cui ◽  
J. G. Cao
Keyword(s):  
Power Density ◽  
Output Power ◽  
Energy Harvester ◽  
Design Guidelines ◽  
Ambient Vibration ◽  
Piezoelectric Bimorph ◽  
Flexural Mode ◽  
Energy Harvesters ◽  
Piezoelectric Energy ◽  
Further Development

AbstractThis article analyzes the performance of a piezoelectric energy harvester in the flexural mode for scavenging ambient vibration energy. The energy harvester consists of a piezoelectric bimorph plate with a variable width. A theoretical study is performed and the computational results show that the output power density increases initially, reaches a maximum, and then decreases monotonically with the increasing width, underscoring the importance for the width design of the scavenging structure. Further analysis indicates that the peak of output power density is determined by both the bimorph deformation amplitude and the efficiency in scavenging-energy. The analysis for this simplified model piezoelectric harvester provides a framework for further development on design guidelines for piezoelectric energy harvesters of optimal performance.

Sign in / Sign up

Export Citation Format

Share Document