Realization of Maximal Wind Energy Tracking Control Subsystem Based on RTDS

2013 ◽  
Vol 655-657 ◽  
pp. 1500-1504
Author(s):  
Ran Ran An ◽  
Yu Lan Hu ◽  
Tao Ding ◽  
Jia Yong Zhong

The paper introduces the theory of maximal wind energy tracking based on wind turbine aerodynamic theory, based on which methods to realize are provided and control subsystem is build on RTDS. Simulating results on RTDS, of whole DFIG wind generating system, showed the method is feasible and the control subsystem is correct and effective.

2017 ◽  
Vol 7 (2) ◽  
pp. 77-91
Author(s):  
Merabet Leila ◽  
Mekki Mounira ◽  
Ourici Amel ◽  
Saad Salah

This paper describes the modelling and control system of a wind turbine, using a doubly fed induction generator. This configuration makes the wind turbine suitable for variable speed wind energy application. The power captured by the wind turbine is converted into electrical power by the induction generator, and it is transmitted to the grid by the stator and the rotor windings. The control system generates voltage command signals for rotor converter and grid converter, respectively, in order to control the power of the wind turbine. Reactive power exchanged with the network through the converters is set to 0 VAr. The control strategy has been developed using MATLAB/Simulink. The simulation results are presented and discussed in the conclusions. Keywords: Wind energy, doubly fed induction generator, grid power, modelling, control.


2015 ◽  
Vol 793 ◽  
pp. 333-337 ◽  
Author(s):  
Abadal Salam T. Hussain ◽  
S. Faiz Ahmed ◽  
F. Malek ◽  
M.S. Jawad ◽  
Nursabrina Noorpi ◽  
...  

In many countries fossil fuels are used as the main source to generate electricity, but due to the increase in energy consumption and the rapid depletion of the fossil fuel resources, the demand of alternate energy sources such as solar, wind or hydro power becomes high [1]. In this paper wind energy as an alternate energy resource for electric power generation is proposed in the form of a small wind farm for grid-connected application in Perlis Malaysia. The monthly wind speed data of Perlis which is the smallest state of Malaysia were measured and the wind mill parameters such as Air Density, Blade Length, Power Coefficient and Blade Length were calculated. The mechanical output power of the proposed wind turbine form is calculated to check out its performance and reliability. The results showed that the proposed wind energy power generating system is a good choice and can be implemented in Malaysia to provide enough power for small towns and rural areas.


2019 ◽  
pp. 0309524X1988936
Author(s):  
Taoufik Sandabad ◽  
Mohammed Rachidi ◽  
Omar Dahhani

In this article, we process the modeling and control of a global chain of the wind energy conversion system based on a permanent magnet synchronous generator, and the injection of the produced energy into electrical grid. The proposed control technique of the wind energy system is based on a sliding mode control which is designed for a variable speed wind turbine. Sliding mode control is assessed on a wind turbine to supply three phases grid. The aim in this work is to operate over all the wind conversion system at its maximum power point. Initially, three controls have been designed by sliding mode control: the first is for electromagnetic torque of the used permanent magnet synchronous generator, the second is for the machine side converter, and the last is for the grid side converter. Thereafter, another proportional integral controller has been designed for the phase looked loop. Finally, the permanent magnet synchronous generator–based wind turbine and the grid are modeled, and proposed controls are applied, various simulations results by MATLAB/SIMULINK environment are presented and discussed.


2016 ◽  
Vol 65 (4) ◽  
pp. 643-656 ◽  
Author(s):  
Piotr Gajewski ◽  
Krzysztof Pieńkowski

Abstract The paper presents the advanced control system of the wind energy conversion with a variable speed wind turbine. The considered system consists of a wind turbine with the permanent magnet synchronous generator (PMSG), machine side converter (MSC), grid side converter (GSC) and control circuits. The mathematical models of a wind turbine system, the PMSG generator and converters have been described. The control algorithms of the converter systems based on the methods of vector control have been applied. In the advanced control system of the machine side converter the optimal MPPT control method has been used. Additionally the pitch control scheme is included in order to achieve the limitation of maximum power and to prevent mechanical damage of the wind turbine. In the control system of the grid side converter the control of active and reactive power has been applied with the application of Voltage Oriented Control (VOC). The performance of the considered wind energy system has been studied by digital simulation. The results of simulation studies confirmed the good effectiveness of the considered wind turbine system and very good performance of the proposed methods of vector control and control systems.


Author(s):  
S. G. Ignatiev ◽  
S. V. Kiseleva

Optimization of the autonomous wind-diesel plants composition and of their power for guaranteed energy supply, despite the long history of research, the diversity of approaches and methods, is an urgent problem. In this paper, a detailed analysis of the wind energy characteristics is proposed to shape an autonomous power system for a guaranteed power supply with predominance wind energy. The analysis was carried out on the basis of wind speed measurements in the south of the European part of Russia during 8 months at different heights with a discreteness of 10 minutes. As a result, we have obtained a sequence of average daily wind speeds and the sequences constructed by arbitrary variations in the distribution of average daily wind speeds in this interval. These sequences have been used to calculate energy balances in systems (wind turbines + diesel generator + consumer with constant and limited daily energy demand) and (wind turbines + diesel generator + consumer with constant and limited daily energy demand + energy storage). In order to maximize the use of wind energy, the wind turbine integrally for the period in question is assumed to produce the required amount of energy. For the generality of consideration, we have introduced the relative values of the required energy, relative energy produced by the wind turbine and the diesel generator and relative storage capacity by normalizing them to the swept area of the wind wheel. The paper shows the effect of the average wind speed over the period on the energy characteristics of the system (wind turbine + diesel generator + consumer). It was found that the wind turbine energy produced, wind turbine energy used by the consumer, fuel consumption, and fuel economy depend (close to cubic dependence) upon the specified average wind speed. It was found that, for the same system with a limited amount of required energy and high average wind speed over the period, the wind turbines with lower generator power and smaller wind wheel radius use wind energy more efficiently than the wind turbines with higher generator power and larger wind wheel radius at less average wind speed. For the system (wind turbine + diesel generator + energy storage + consumer) with increasing average speed for a given amount of energy required, which in general is covered by the energy production of wind turbines for the period, the maximum size capacity of the storage device decreases. With decreasing the energy storage capacity, the influence of the random nature of the change in wind speed decreases, and at some values of the relative capacity, it can be neglected.


Author(s):  
J. V. Muruga Lal Jeyan ◽  
Akhila Rupesh ◽  
Jency Lal

The aerodynamic module combines the three-dimensional nonlinear lifting surface theory approach, which provides the effective propagated incident velocity and angle of attack at the blade section separately, and a two-dimensional panel method for steady axisymmetric and non-symmetric flow has to be involved to obtain the 3D pressure and velocity distribution on the wind mill model blade. Wind mill and turbines have become an economically competitive form of efficiency and renewable work generation. In the abroad analytical studies, the wind turbine blades to be the target of technological improvements by the use of highly possible systematic , aerodynamic and design, material analysis, fabrication and testing. Wind energy is a peculiar form of reduced form of density source of power. To make wind power feasible, it is important to optimize the efficiency of converting wind energy into productivity source. Among the different aspects involved, rotor aerodynamics is a key determinant for achieving this goal. There is a tradeoff between thin airfoil and structural efficiency. Both of which have a strong impact on the cost of work generated. Hence the design and analysis process for optimum design requires determining the load factor, pressure and velocity impact and optimum thickness distribution by finding the effect of blade shape by varying thickness on the basis of both the aerodynamic output and the structural weight.


Sign in / Sign up

Export Citation Format

Share Document