Surface Roughness Influence on O2 and Ar RIE Gas Treated Aluminum Surface

2014 ◽  
Vol 925 ◽  
pp. 92-95
Author(s):  
Zaliman Sauli ◽  
Vithyacharan Retnasamy ◽  
Uda Hashim ◽  
Steven Taniselass ◽  
Moganraj Palianysamy ◽  
...  
Keyword(s):  
Surface Roughness ◽  
Atomic Force Microscopy ◽  
Design Of Experiment ◽  
Surface Characteristics ◽  
Aluminum Surface ◽  
Root Mean Square Roughness ◽  
Mean Square ◽  
Bias Power ◽  
Force Microscopy ◽  
Atomic Force

This study reports on the preliminary investigations on the effect of Reactive Ion Etch (RIE) parameters on the surface characteristics of Al bond pad. Investigation is done employing Design of Experiment (DOE) method. Quantity of Oxygen, Argon, ICP power and BIAS power were varied to get 16 sets of recipes. This provides 16 samples with different combination of RIE parameters. Surface characteristics of the samples were analyzed using Atomic Force Microscopy (AFM).Data collected were in terms of Surface Roughness (RA), Peak Vs Valley (P-V) and Surface Root-Mean-Square Roughness (RMS). Result shows that combination of these RIE parameters does not vastly affect the surface characteristics of the Al bond pad.

scholarly journals Novel Zirconia Surface Treatments for Enhanced Osseointegration: Laboratory Characterization

2014 ◽  
Vol 2014 ◽  
pp. 1-8 ◽  
Author(s):  
Ola H. Ewais ◽  
Fayza Al Abbassy ◽  
Mona M. Ghoneim ◽  
Moustafa N. Aboushelib
Keyword(s):  
Surface Roughness ◽  
Atomic Force Microscopy ◽  
Surface Hardness ◽  
Surface Characteristics ◽  
Low Pressure ◽  
Surface Treatments ◽  
Control Surface ◽  
Force Microscopy ◽  
Atomic Force ◽  
Zirconia Implants

Purpose. The aim of this study was to evaluate three novel surface treatments intended to improve osseointegration of zirconia implants: selective infiltration etching treatment (SIE), fusion sputtering (FS), and low pressure particle abrasion (LPPA). The effects of surface treatments on roughness, topography, hardness, and porosity of implants were also assessed.Materials and Methods. 45 zirconia discs (19 mm in diameter × 3 mm in thickness) received 3 different surface treatments: selective infiltration etching, low pressure particle abrasion with 30 µm alumina, and fusion sputtering while nontreated surface served as control. Surface roughness was evaluated quantitatively using profilometery, porosity was evaluated using mercury prosimetry, and Vickers microhardness was used to assess surface hardness. Surface topography was analyzed using scanning and atomic force microscopy (α=0.05).Results. There were significant differences between all groups regarding surface roughness (F=1678,P<0.001), porosity (F=3278,P<0.001), and hardness (F=1106.158,P<0.001). Scanning and atomic force microscopy revealed a nanoporous surface characteristic of SIE, and FS resulted in the creation of surface microbeads, while LPPA resulted in limited abrasion of the surface.Conclusion. Within the limitations of the study, changes in surface characteristics and topography of zirconia implants have been observed after different surface treatment approaches. Thus possibilities for enhanced osseointegration could be additionally offered.

Surface Roughness Characterization of ZnO: TiO2-Organic Blended Solar Cells Layers by Atomic Force Microscopy and Fractal Analysis

2014 ◽  
Vol 13 (03) ◽  
pp. 1450020 ◽  
Author(s):  
Ştefan Ţălu ◽  
Sebastian Stach ◽  
Muhammad Ikram ◽  
Dinesh Pathak ◽  
Tomas Wagner ◽  
...  
Keyword(s):  
Surface Roughness ◽  
Atomic Force Microscopy ◽  
Solar Cells ◽  
Fractal Analysis ◽  
Surface Characterization ◽  
Surface Characteristics ◽  
Statistical Parameters ◽  
Force Microscopy ◽  
Atomic Force

The objective of this work is to quantitatively characterize the 3D complexity of ZnO : TiO 2-organic blended solar cells layers by atomic force microscopy and fractal analysis. ZnO : TiO 2-organic blended solar cells layers were investigated by AFM in tapping-mode in air, on square areas of 25 μm2. A detailed methodology for ZnO : TiO 2-organic blended solar cells layers surface fractal characterization, which may be applied for AFM data, is presented. Detailed surface characterization of the surface topography was obtained using statistical parameters, according with ISO 25178-2: 2012. The fractal dimensions Df values (all with average ± standard deviation), obtained with morphological envelopes method, for: blend D1 ( P 3 HT : PCBM : ZnO : TiO 2 blend with ratio 1:0.35:0.175:0.175 mg in 1 ml of Chlorobenzene) is Df = 2.55 ± 0.01; and for blend D2 ( P 3 HT : PCBM : ZnO : TiO 2 blend with ratio 1:0.55:0.075:0.075 mg in 1 ml of Chlorobenzene) is Df = 2.45 ± 0.01. Denoting the ratios in 1 ml of Chlorobenzene with D1 and D2 articles. The 3D surface roughness of samples revealed a fractal structure at nanometer scale. Fractal and AFM analysis may assist manufacturers in developing ZnO : TiO 2-organic blended solar cells layers with better surface characteristics and provides different yet complementary information to that offered by traditional surface statistical parameters.

Influence of Surface Roughness on Breakdown Voltage of 4H-SiC SBD with FLR Structure

2009 ◽  
Vol 615-617 ◽  
pp. 643-646 ◽  
Author(s):  
Akimasa Kinoshita ◽  
Takashi Nishi ◽  
Takasumi Ohyanagi ◽  
Tsutomu Yatsuo ◽  
Kenji Fukuda ◽  
...  
Keyword(s):  
Surface Roughness ◽  
Breakdown Voltage ◽  
Room Temperature ◽  
Light Emission ◽  
Root Mean Square Roughness ◽  
Avalanche Breakdown ◽  
Mean Square ◽  
Electrical Field ◽  
Force Microscopy ◽  
Atomic Force

The Ti/4H-SiC Schottky barrier diodes with a field limiting ring (FLR) structure are fabricated. Two types of SBDs are prepared; one (SBD-A) is covered and another (SBD-B) isn’t covered with a carbon cap during high temperature annealing after ion implantation. The breakdown voltage at room temperature for SBD-A and SBD-B are 1400 V and 1000 V, respectively. The breakdown for both SBDs occurs due to an avalanche breakdown. The light emission images are obtained at the breakdown voltage by photo emission microscope (PEM). The light emission is observed along an FLR of the SBD-A as designed. On the other hand, the spot of light emission is observed on a FLR structure of the SBD-B. This light emission spot indicates that leakage current is concentrated because an electrical field concentration is generated at this one for the SBD-B. The root-mean-square roughness of the Al-implanted region on the FLR structure calculated from the atomic force microscopy (AFM) images for the SBD-A and the SBD-B are 0.697 nm and 5.58 nm, respectively. Therefore it is considered that large surface roughness on the FLR decreases breakdown voltage of SBD because an electrical field concentration is generated at a spot.

Brittle Behaviour in Aspirin Crystals: Evidence of Spalling Fracture

2020 ◽  
Author(s):  
Benjamin P. A. Gabriele ◽  
Craig J. Williams ◽  
Douglas Stauffer ◽  
Brian Derby ◽  
Aurora J. Cruz-Cabeza
Keyword(s):  
Surface Roughness ◽  
Atomic Force Microscopy ◽  
Single Crystals ◽  
Spalling Fracture ◽  
Force Microscopy ◽  
Atomic Force ◽  
Afm Imaging

<div> <div> <div> <p>Single crystals of aspirin form I were cleaved and indented on their dominant face. Upon inspection, it was possible to observe strongly anisotropic shallow lateral cracks due to the extreme low surface roughness after cleavage. Atomic Force Microscopy (AFM) imaging showed spalling fractures nucleating from the indent corners, forming terraces with a height of one or two interplanar spacings d100. The formation of such spalling fractures in aspirin was rationalised using basic calculations of attachment energies, showing how (100) layers are poorly bonded when compared to their relatively higher intralayer bonding. An attempt at explaining the preferential propagation of these fractures along the [010] direction is discussed. </p> </div> </div> </div>

Brittle Behaviour in Aspirin Crystals: Evidence of Spalling Fracture

2020 ◽  
Author(s):  
Benjamin P. A. Gabriele ◽  
Craig J. Williams ◽  
Douglas Stauffer ◽  
Brian Derby ◽  
Aurora J. Cruz-Cabeza
Keyword(s):  
Surface Roughness ◽  
Atomic Force Microscopy ◽  
Single Crystals ◽  
Spalling Fracture ◽  
Force Microscopy ◽  
Atomic Force ◽  
Afm Imaging

<div> <div> <div> <p>Single crystals of aspirin form I were cleaved and indented on their dominant face. Upon inspection, it was possible to observe strongly anisotropic shallow lateral cracks due to the extreme low surface roughness after cleavage. Atomic Force Microscopy (AFM) imaging showed spalling fractures nucleating from the indent corners, forming terraces with a height of one or two interplanar spacings d100. The formation of such spalling fractures in aspirin was rationalised using basic calculations of attachment energies, showing how (100) layers are poorly bonded when compared to their relatively higher intralayer bonding. An attempt at explaining the preferential propagation of these fractures along the [010] direction is discussed. </p> </div> </div> </div>

scholarly journals Atomic force microscopy comparative analysis of the surface roughness of two posterior chamber phakic intraocular lens models: ICL versus IPCL

2021 ◽  
Vol 21 (1) ◽  
Author(s):  
Juan Gros-Otero ◽  
Samira Ketabi ◽  
Rafael Cañones-Zafra ◽  
Montserrat Garcia-Gonzalez ◽  
Cesar Villa-Collar ◽  
...  
Keyword(s):  
Surface Roughness ◽  
Atomic Force Microscopy ◽  
Intraocular Lenses ◽  
Posterior Chamber ◽  
Anterior Surface ◽  
Contact Mode ◽  
Force Microscopy ◽  
Atomic Force ◽  
Phakic Intraocular Lenses ◽  
Roughness Measurements

Abstract Background To compare the anterior surface roughness of two commercially available posterior chamber phakic intraocular lenses (IOLs) using atomic force microscopy (AFM). Methods Four phakic IOLs were used for this prospective, experimental study: two Visian ICL EVO+ V5 lenses and two iPCL 2.0 lenses. All of them were brand new, were not previously implanted in humans, were monofocal and had a dioptric power of − 12 diopters (D). The anterior surface roughness was assessed using a JPK NanoWizard II® atomic force microscope in contact mode immersed in liquid. Olympus OMCL-RC800PSA commercial silicon nitride cantilever tips were used. Anterior surface roughness measurements were made in 7 areas of 10 × 10 μm at 512 × 512 point resolution. The roughness was measured using the root-mean-square (RMS) value within the given regions. Results The mean of all anterior surface roughness measurements was 6.09 ± 1.33 nm (nm) in the Visian ICL EVO+ V5 and 3.49 ± 0.41 nm in the iPCL 2.0 (p = 0.001). Conclusion In the current study, we found a statistically significant smoother anterior surface in the iPCL 2.0 phakic intraocular lenses compared with the VISIAN ICL EVO+ V5 lenses when studied with atomic force microscopy.

Copper Diffusion Into Aluminum-Silicon Metallizations by Accelerated Thermal and Electrical Stressing

1996 ◽  
Vol 428 ◽  
Author(s):  
G. O. Ramseyer ◽  
L. H. Walsh ◽  
J. V. Beasock ◽  
H. F. Helbig ◽  
R. C. Lacoe ◽  
...  
Keyword(s):  
Surface Roughness ◽  
Atomic Force Microscopy ◽  
Electron Spectroscopy ◽  
Auger Electron ◽  
Depth Profiling ◽  
Copper Diffusion ◽  
Force Microscopy ◽  
Atomic Force ◽  
Line Widths ◽  
Electromigration Lifetime

AbstractPatterned 930 nm Al(1%-Si) interconnects over 147 nm of Cu were electromigration lifetime tested at 1.0–1.5 × 105 A/cm2 at 250 °C. The morphology of the surfaces of the electromigrated stripes with different line widths and times to failure were characterized by atomic force microscopy, and changes in surface roughness were compared. The diffusion of copper into the electromigrated aluminum stripes was determined by depth profiling using Auger electron spectroscopy. In particular, areas where hillocks formed were examined and compared to areas of median roughness.

Scaling Analysis of a- and poly-Si Surface Roughness by Atomic Force Microscopy

1994 ◽  
Vol 367 ◽  
Author(s):  
T. Yoshinobu ◽  
A. Iwamoto ◽  
K. Sudoh ◽  
H. Iwasaki
Keyword(s):  
Surface Roughness ◽  
Atomic Force Microscopy ◽  
Surface Area ◽  
Scaling Behavior ◽  
Linear Size ◽  
Scaling Analysis ◽  
Macroscopic Scale ◽  
Force Microscopy ◽  
Atomic Force ◽  
Roughness Exponent

AbstractThe scaling behavior of the surface roughness of a-and poly-Si deposited on Si was investigated by atomic force microscopy (AFM). The interface width W(L), defined as the rms roughness as a function of the linear size of the surface area, was calculated from various sizes of AFM images. W(L) increased as a power of L with the roughness exponent ∝ on shorter length scales, and saturated at a constant value of on a macroscopic scale. The value of roughness exponent a was 0.48 and 0.90 for a-and poly-Si, respectively, and σ was 1.5 and 13.6nm for 350nm-thick a-Si and 500nm-thick poly-Si, respectively. The AFM images were compared with the surfaces generated by simulation.

Sign in / Sign up

Export Citation Format

Share Document