scholarly journals Comparison between Conventional Shot Peening (SP) and Surface Mechanical Attrition Treatment (SMAT) on a Titanium Alloy

2014 ◽  
Vol 996 ◽  
pp. 964-968 ◽  
Author(s):  
Donaro Gallitelli ◽  
Delphine Retraint ◽  
Emmanuelle Rouhaud
Keyword(s):  
Experimental Data ◽  
Residual Stress ◽  
Titanium Alloy ◽  
Shot Peening ◽  
Surface Characteristics ◽  
Surface Mechanical Attrition Treatment ◽  
Mechanical Attrition ◽  
Stress Profiles ◽  
Stress States ◽  
Analytical Approaches

In this paper the residual stress states induced by conventional shot peening (SP) and surface mechanical attrition treatment (SMAT) are compared. The treated part correspond to plates made of a titanium alloy. Different intensities of these two mechanical treatments are first considered: their influence on the surface characteristics (roughness, hardness...) is studied. These experimental data are then used to develop a model for the residual stress profiles with dimensional analysis, Experimental and analytical approaches are then discussed.

Ultrasonic Evaluation of Compressive Residual Stress of Surface Treated Metals

2005 ◽  
Vol 490-491 ◽  
pp. 184-189 ◽  
Author(s):  
Farid Belahcene ◽  
Xiaolai Zhou ◽  
Jian Lu
Keyword(s):  
Experimental Data ◽  
Residual Stresses ◽  
Nondestructive Evaluation ◽  
Subsurface Layer ◽  
Surface Mechanical Attrition Treatment ◽  
Shallow Subsurface ◽  
Ultrasonic Evaluation ◽  
Mechanical Attrition ◽  
Machine Parts ◽  
Compressive Residual Stresses

Shot peening is an effective method of improving fatigue performance of machine parts in the industry by producing a thin surface layer of compressive residual stresses that prevents crack initiation and retards crack growth during service. Nondestructive evaluation of the prevailing compressive residual stresses in the shallow subsurface layer is realized by the critically refracted longitudinal (Lcr) waves. This paper presents experimental data obtained on SMAT (surface mechanical attrition treatment) steel alloy S355 sample. Comparative travel-time shows that there are statistically significant differences in treated and untreated specimen. With knowledge of the acoustoelastic constants which are obtained by a test calibration, the experimental data indicates that compressive residual stresses are distributed near subsurface (hundreds of micron). These stress results show that the Lcr technique is efficient for evaluation of residual stresses after the surface treatment.

Surface Modification Analysis after Shot Peening of AA 7075 in Different States

2013 ◽  
Vol 768-769 ◽  
pp. 519-525 ◽  
Author(s):  
Sebastjan Žagar ◽  
Janez Grum
Keyword(s):  
Residual Stress ◽  
Surface Layer ◽  
Residual Stresses ◽  
Aluminium Alloy ◽  
Shot Peening ◽  
Fatigue Testing ◽  
Stress Profile ◽  
Treatment Conditions ◽  
Stress Profiles ◽  
Compressive Residual Stresses

The paper deals with the effect of different shot peening (SP) treatment conditions on the ENAW 7075-T651 aluminium alloy. Suitable residual stress profile increases the applicability and life cycle of mechanical parts, treated by shot peening. The objective of the research was to establish the optimal parameters of the shot peening treatment of the aluminium alloy in different precipitation hardened states with regard to residual stress profiles in dynamic loading. Main deformations and main residual stresses were calculated on the basis of electrical resistance. The resulting residual stress profiles reveal that stresses throughout the thin surface layer of all shot peened specimens are of compressive nature. The differences can be observed in the depth of shot peening and the profile of compressive residual stresses. Under all treatment conditions, the obtained maximum value of compressive residual stress ranges between -200 MPa and -300 MPa at a depth between 250 μm and 300 μm. Comparison of different temperature-hardened aluminium alloys shows that changes in the Almen intensity values have greater effect than coverage in the depth and profile of compressive residual stresses. Positive stress ratio of R=0.1 was selected. Wöhler curves were determined in the areas of maximum bending loads between 30 - 65 % of material's tensile strength, measured at thinner cross-sections of individual specimens. The results of material fatigue testing differ from the level of shot peening on the surface layer.

Effect of the Type of Grinding Wheel on the Surface Characteristics of a Titanium Alloy with Internal Coolant Supply

2019 ◽  
Vol 825 ◽  
pp. 92-98
Author(s):  
Nakatsuka Nagatoshi ◽  
Sumito Toyokawa ◽  
Atsushi Kusakabe ◽  
Shinya Nakatsukasa ◽  
Hiroyuki Sasahara
Keyword(s):  
Residual Stress ◽  
Surface Roughness ◽  
Silicon Carbide ◽  
Titanium Alloy ◽  
Aluminum Oxide ◽  
Compressive Residual Stress ◽  
Surface Characteristics ◽  
Grinding Wheel

The objective of this paper is to clarify the effect of grinding surface characteristics in the grinding of a titanium alloy with a coolant supply from the inner side of the grinding wheel. In this paper, we selected a white aluminum oxide (WA) vitrified bonded grinding wheel and a green silicon carbide (GC) vitrified bonded grinding wheel, and compared their grinding characteristics. As a result, in the case of the GC vitrified bonded grinding wheel, the surface roughness decreased by about 54% and the compressive residual stress increased by about 128%.

Effect of Microshot Peening on Surface Characteristics of Spring Steel

2010 ◽  
Vol 654-656 ◽  
pp. 374-377
Author(s):  
Yasunori Harada ◽  
Koji Yoshida
Keyword(s):  
Residual Stress ◽  
Shot Peening ◽  
Compressive Residual Stress ◽  
Cast Steel ◽  
High Hardness ◽  
Surface Characteristics ◽  
Spring Steel ◽  
Cemented Carbide ◽  
High Carbon ◽  
New Type

Shot peening is a surface treatment that improves the performance of engineering components. In conventional shot peening, the medium consists of small spheres, which are usually made of high-carbon cast steel; the diameter of the spheres is in the range from 0.3 to 1.2mm. More recently, however, a new type of microshot has been developed to enhance the peening effect. The diameter of the spheres in the new medium is in the range from 0.02 to 0.15mm. In the present study, the effect of microshot peening on the surface characteristics of spring steel was investigated. The injection method of the microshot was of the compressed air type. The microshots of 0.1mm diameter were high-carbon cast steel and cemented carbide, and the workpiece used was the commercially spring steel JIS-SUP10. The surface roughness, hardness and compressive residual stress of the peened workpieces were measured. The surface layer of the workpieces was sufficiently deformed by microshot peening. A high hardness or residual stress was observed near the surface. The use of hard microshots such as cemented carbide was found to cause a significantly enhanced peening effect for spring steel.

Effect of shot peening time on δ/γ residual stress profiles of AISI 304 weld

2020 ◽  
Vol 284 ◽  
pp. 116747 ◽  
Author(s):  
Hsuan-Han Lai ◽  
Hao-Chung Cheng ◽  
Chen-Yu Lee ◽  
Chi-Ming Lin ◽  
Weite Wu
Keyword(s):  
Residual Stress ◽  
Shot Peening ◽  
Aisi 304 ◽  
Stress Profiles

Incorporating the principles of shot peening for a better understanding of surface mechanical attrition treatment (SMAT) by simulations and experiments

2017 ◽  
Vol 116 ◽  
pp. 365-373 ◽  
Author(s):  
Asghar Heydari Astaraee ◽  
Reza Miresmaeili ◽  
Sara Bagherifard ◽  
Mario Guagliano ◽  
Mahmood Aliofkhazraei
Keyword(s):  
Shot Peening ◽  
Surface Mechanical Attrition Treatment ◽  
Mechanical Attrition

Influence of Shot-Peening Parameters on the Sub-Surface Residual Stress Profiles in Al-7075 Alloy Components

2013 ◽  
Vol 768-769 ◽  
pp. 66-71 ◽  
Author(s):  
Diego Cecchin ◽  
Cristy Leonor Azanza Ricardo ◽  
Mirco D'Incau ◽  
Michele Bandini ◽  
Paolo Scardi
Keyword(s):  
Residual Stress ◽  
Stress Analysis ◽  
Shot Peening ◽  
Stress Gradient ◽  
Stress Profile ◽  
Surface Residual Stress ◽  
X Ray ◽  
Al 7075 ◽  
Stress Profiles ◽  
Residual Stress Analysis

Aluminum alloy (Al-7075-T6) samples were analyzed to determine the in-depth residual stress profile induced by a shot-peening treatment. The influence of coverage degree and Almen intensity on the surface residual stress and on the sub-surface residual stress gradient was investigated. Residual stress profiles were obtained using three different techniques: (i) standard laboratory X-ray diffraction (XRD) residual stress analysis with progressive chemical layer-removal; (ii) XRD residual stress analysis with synchrotron radiation using different X-ray energies, thus changing the penetration depths, and (iii) Blind Hole Drilling (BHD). A comprehensive comparison of the results given by the used techniques is shown.

scholarly journals Residual Stress State of X65 Pipeline Girth Welds Before and After Local and Furnace Post Weld Heat Treatment

2016 ◽  
Author(s):  
Yao Ren ◽  
Anna Paradowska ◽  
Bin Wang ◽  
Elvin Eren
Keyword(s):  
Heat Treatment ◽  
Residual Stress ◽  
Residual Stresses ◽  
Outer Surface ◽  
Post Weld Heat Treatment ◽  
Stress Profiles ◽  
Stress States ◽  
Girth Welds ◽  
Welded Pipe ◽  
Weld Heat

This research investigated the effects of global (in other words, furnace-based) and local post weld heat treatment (PWHT) on residual stress (RS) relaxation in API 5L X65 pipe girth welds. Two pipe spools were fabricated using identical pipeline production procedures for manufacturing multi-pass narrow gap welds. Non-destructive neutron diffraction strain scanning was carried out on girth welded pipe spools and stress-free comb samples and also thin slices for the determination of lattice spacing. All residual stress measurements were carried out at the KOWARI strain scanning instrument at the Australian Nuclear Science and Technology Organization (ANSTO). Residual stresses of two pipe spools (in the as-welded condition) were measured through the thickness in the weld material and adjacent parent metal starting from the weld toe. Three line-scans were completed 3mm below outer surface, at mid thickness and 3mm above the inner surface. PWHT was adopted for stress relaxation; one pipe was conventionally heat treated entirely in an enclosed furnace and the other was locally heated by a flexible ceramic heating pad. Residual stresses were measured after PWHT at exactly the same locations as those used for the as-welded condition. Residual stress states of the two pipe spools in as-welded condition and after PWHT were compared and the results were presented in full stress maps. Additionally, through thickness residual stress profiles and the results of one line scan (3mm below outer surface) were compared with the respective residual stress profiles advised in British Standard BS 7910 “Guide to methods for assessing the acceptability of flaws in metallic structures” and the UK nuclear industry’s R6 procedure. The residual stress states of the two pipe spools measured in the as-welded condition were similar. With the given parameters, local PWHT has effectively reduced residual stresses in the pipe spool to such a level that it prompted the thought that local PWHT can be considered a substitute for global PWHT.

Sign in / Sign up

Export Citation Format

Share Document