Design and Static Structural Analysis of a 2.5 kW Combined Darrieus-Savonius Wind Turbine

2017 ◽  
Vol 30 ◽  
pp. 94-99 ◽  
Author(s):  
Fateh Ferroudji ◽  
Cherif Khelifi ◽  
Farouk Meguellati ◽  
Khaled Koussa
Keyword(s):  
Wind Speed ◽  
Wind Turbine ◽  
Three Dimensional ◽  
Wind Pressure ◽  
Galvanized Steel ◽  
Element Analysis ◽  
Critical Loading ◽  
Savonius Wind Turbine ◽  
The Stability ◽  
Von Mises

Modeling and simulation of mechanical structures in development phase are fundamental to optimize and improve the stability and reliability of the final product as well as to reduce the cost of prototyping and testing. Wind turbines are subject to critical loading to the centrifugal force due to wind speed and gravitational force. The present study discusses three-dimensional numerical simulations of combined Darrieus-Savonius wind turbine D-SWT for applications in urban and isolated areas for lighting, pumping water, etc. The Darrieus turbine is used to produce wind power and the Savonius rotor to start the system. Finite Element Analysis (FEA) using SolidWorks 2015 is employed to generate the geometry of the structure and SolidWorks Simulation to investigate the stability and reliability static on the structure of the D-WST built by two types of material of the blade Galvanized Steel (GS) and Aluminum alloys 1060-H18 (ALU). Mechanical parameter of the structure are calculated for critical loading conditions, including the gravity and wind pressure loading due to the wind speed of 23m/s. Simulations results indicate no structural failure is predicted for all components of the D-SWT for both materials used according to Von Mises criterion stresses and the factors of safety of the most fragile material are greater than (the unity) 1. The maximum displacements found (3.84 & 6.81mm), occurred at the tip blades (free ends levels). These displacements are accepted relatively to the structure size.

Three-Dimensional Modeling and Finite Element Analysis of an Ankle External Fixator

2020 ◽  
Vol 899 ◽  
pp. 94-102
Author(s):  
Nur Faiqa Ismail ◽  
Muhammmad Aiman Firdaus Bin Adnan ◽  
Solehuddin Shuib ◽  
Nik Ahmad Hambali Nik Abd Rashid
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
External Fixator ◽  
Three Dimensional ◽  
Von Mises Stress ◽  
External Fixators ◽  
Element Analysis ◽  
Stress And Deformation ◽  
The Stability ◽  
Von Mises

External fixator has played an important role in repairing fractured ankle bone. This surgery is done due to the several factors which are the bone is not normal position or has broken into several pieces. The external fixator will help the broken bone to grow and remodel back to the original appearance. However, there are some issues regarding to the stability of this fixation. Improper design and material are the major factor that decreased the stability since it is related to the deformation of the external fixator to hold the bone fracture area. This study aims to design a stable structure for constructing delta frame ankle external fixator to increase the stability of the fixation. There are two designs of external fixator with two types of material used in this present study. Both external fixators with different materials are analyzed in terms of von Mises stress and deformation by using a conventional Finite Element Analysis software; ANSYS Workbench V15. The result obtained shows the Model 1 with stainless steel has less stress and deformation distributions compared to the Model 2. Hence, by using Model 1 as the external fixator, the stability of the fixation can be increased.

Dynamic Response Analysis of Large Wind Turbine Blade Based on Davenport Wind Speed Model

2011 ◽  
Vol 347-353 ◽  
pp. 2330-2336
Author(s):  
Jian Ping Zhang ◽  
Dong Liang Li ◽  
Yu Liu ◽  
He Len Wu ◽  
Jian Xing Ren ◽  
...  
Keyword(s):  
Wind Speed ◽  
Wind Turbine ◽  
Turbine Blade ◽  
Vibration Amplitude ◽  
Wind Turbine Blade ◽  
Von Mises Stress ◽  
Growth Trend ◽  
Element Analysis ◽  
Von Mises ◽  
Fluctuating Wind

Fluctuating wind speed spectrum, which is closer to the actual working conditions, was simulated by davenport wind speed model, and displacement and stress distribution of blade under fluctuating wind speed were calculated by finite element analysis software. The numerical results indicate that the growth trend of vibration amplitude for whole blade at flapping direction is nonlinear along the wingspan. The max von-mises stress appears when the vibration amplitude of tip reaches the maximum, and it is mainly concentrated in the central part of the blade. The stress at trailing edge and tip is smaller than the central part. Above results provide a reference for the strength safety design of wind turbine blade.,Fluctuating wind speed spectrum, which is closer to the actual working conditions, was simulated by davenport wind speed model, and displacement and stress distribution of blade under fluctuating wind speed were calculated by finite element analysis software. The numerical results indicate that the growth trend of vibration amplitude for whole blade at flapping direction is nonlinear along the wingspan. The max von-mises stress appears when the vibration amplitude of tip reaches the maximum, and it is mainly concentrated in the central part of the blade. The stress at trailing edge and tip is smaller than the central part. Above results provide a reference for the strength safety design of wind turbine blade.

Effects of occlusal scheme on All-on-Four abutments, screws and prostheses: A three-dimensional finite element study

2020 ◽  
Author(s):  
Nurullah Türker ◽  
Hümeyra Tercanlı Alkış ◽  
Steven J Sadowsky ◽  
Ulviye Şebnem Büyükkaplan
Keyword(s):  
Finite Element ◽  
Three Dimensional ◽  
Good Prognosis ◽  
Von Mises Stress ◽  
Element Analysis ◽  
Group Function ◽  
Occlusal Contact ◽  
Maximum Deformation ◽  
Contact Points ◽  
Von Mises

An ideal occlusal scheme plays an important role in a good prognosis of All-on-Four applications, as it does for other implant therapies, due to the potential impact of occlusal loads on implant prosthetic components. The aim of the present three-dimensional (3D) finite element analysis (FEA) study was to investigate the stresses on abutments, screws and prostheses that are generated by occlusal loads via different occlusal schemes in the All-on-Four concept. Three-dimensional models of the maxilla, mandible, implants, implant substructures and prostheses were designed according to the All-on-Four concept. Forces were applied from the occlusal contact points formed in maximum intercuspation and eccentric movements in canine guidance occlusion (CGO), group function occlusion (GFO) and lingualized occlusion (LO). The von Mises stress values for abutment and screws and deformation values for prostheses were obtained and results were evaluated comparatively. It was observed that the stresses on screws and abutments were more evenly distributed in GFO. Maximum deformation values for prosthesis were observed in the CFO model for lateral movement both in the maxilla and mandible. Within the limits of the present study, GFO may be suggested to reduce stresses on screws, abutments and prostheses in the All-on-Four concept.

scholarly journals Biomechanical assessment of different fixation methods in mandibular high sagittal oblique osteotomy using a three-dimensional finite element analysis model

2021 ◽  
Vol 11 (1) ◽  
Author(s):  
Charles Savoldelli ◽  
Elodie Ehrmann ◽  
Yannick Tillier
Keyword(s):  
Finite Element ◽  
Stress Distribution ◽  
Three Dimensional ◽  
Von Mises Stress ◽  
Analysis Model ◽  
Element Analysis ◽  
Fixation Methods ◽  
Oblique Osteotomy ◽  
Von Mises

AbstractWith modern-day technical advances, high sagittal oblique osteotomy (HSOO) of the mandible was recently described as an alternative to bilateral sagittal split osteotomy for the correction of mandibular skeletal deformities. However, neither in vitro nor numerical biomechanical assessments have evaluated the performance of fixation methods in HSOO. The aim of this study was to compare the biomechanical characteristics and stress distribution in bone and osteosynthesis fixations when using different designs and placing configurations, in order to determine a favourable plating method. We established two finite element models of HSOO with advancement (T1) and set-back (T2) movements of the mandible. Six different configurations of fixation of the ramus, progressively loaded by a constant force, were assessed for each model. The von Mises stress distribution in fixations and in bone, and bony segment displacement, were analysed. The lowest mechanical stresses and minimal gradient of displacement between the proximal and distal bony segments were detected in the combined one-third anterior- and posterior-positioned double mini-plate T1 and T2 models. This suggests that the appropriate method to correct mandibular deformities in HSOO surgery is with use of double mini-plates positioned in the anterior one-third and posterior one-third between the bony segments of the ramus.

scholarly journals Effect of Ring Material and Diameter on Orthopedic Implant Stability: External Fixation in Femur Bone

2018 ◽  
Vol 7 (4.26) ◽  
pp. 190 ◽  
Author(s):  
Nur Fatin Izzati Ibrahim ◽  
Ruslizam Daud ◽  
Muhammad Khairul Ali Hassan ◽  
Noor Ali Hassan ◽  
Noor Alia Md Zain ◽  
...  
Keyword(s):  
External Fixation ◽  
Von Mises Stress ◽  
Axial Stiffness ◽  
Element Analysis ◽  
The Finite Element Analysis ◽  
Ring Diameter ◽  
The Stability ◽  
Von Mises ◽  
Fixation Frame ◽  
Ring Material

Axial stiffness is the most important factor in stability. It is known that any changes in the diameter of any components of the frame will either increase or decrease the axial stiffness of the fixation. The model of implant and bone will be variety as the variables changes. Current studies states that ring stability are one of the most important factors in ensuring fractured bones to have a successful re-union. In circular external fixation, the stability of the pin-bone interaction is influenced by the stability of the fixation frame where the major component is the rings. The objective is to study the finite element analysis (FEA) of the external fixator assembled in human diaphysis under compression force with different materials of the exoskeleton which are stainless steel, titanium alloy, magnesium alloy and carbon fiber. The results obtained show the mechanical strength of each material where it will be used to compare the value of von-Mises stress, stiffness and total deformation to acquire the best suitable ring diameter and material. Based on the result, as the diameter of the ring increases, the stiffness of the ring will be decreased. 

scholarly journals Pre-drilling and self-drilling pins screw-bone fixation stress interaction analysis induced by uniaxial compression loading

2019 ◽  
Vol 15 (1) ◽  
pp. 99-108
Author(s):  
Lim Pei Chee ◽  
Ruslizam Daud ◽  
Shah Fenner Khan Mohamad Khan ◽  
Nurul Alia Md Zain ◽  
Yazid Bajuri
Keyword(s):  
Uniaxial Compression ◽  
External Fixator ◽  
Bone Fractures ◽  
Interaction Analysis ◽  
Compressive Loading ◽  
Three Dimensional ◽  
Maximum Magnitude ◽  
Element Analysis ◽  
Compression Load ◽  
Von Mises

A newly designed Uniaxial external fixator which functions as a universal fixator in the application of all types of bone fractures is recently introduced by both Hospital Universiti Kebangsaan Malaysia (HUKM) and Universiti Malaysia Perlis (UniMAP). The Investigation is focused on identifying and measuring the performance in terms of strength or weakness of the fixator that is needed before the application to the human body. Hence, this research was conducted to determine the performance of Uniaxial external fixator which was based on geometry using different screw drilling techniques applied during an angled uniaxial compression load.  A three-dimensional fixator-bone was constructed using different screw inserting techniques which was then converted into ANSYS v14.5 for the purposes of conducting a finite element analysis (FEA).  Axial compressive loading with various degrees from 60 to 6300 N were applied to bone models to stimulate patient’s daily activities while 10 to 100 N were applied to fixator models for the purposes of reviewing environmental loading to fixator-bone models. Findings revealed that maximum magnitude which caused deformation for predrilling and self-drilling models were located at the highest pin-bone interaction. Conversely, the maximum magnitude of the von Mises strain and stress was located at the lowest pin-bone interaction by omitting the existence of fixator for both Case 1 and 2. There was no obvious difference in the comparison of both models in terms of deformation. However, predrilling models have higher strain and stress than self-drilling models. In sum, findings indicated that self-drilling models have better performance compared to the predrilling models.

Structural Stability Evaluation for Lifting Lug Design of Large Marine Engine by Finite Element Analysis

2007 ◽  
Vol 353-358 ◽  
pp. 2855-2859
Author(s):  
W.C. Lee ◽  
Chae Sil Kim ◽  
J.B. Na ◽  
D.H. Lee ◽  
S.Y. Cho ◽  
...  
Keyword(s):  
Finite Element ◽  
Three Dimensional ◽  
Design Procedure ◽  
Steel Structures ◽  
Stability Evaluation ◽  
Element Analysis ◽  
Marine Engines ◽  
Dimensional Finite Element ◽  
The Stability ◽  
Three Dimensional Finite Element

Since most marine engines are generally very huge and heavy, it is required to keep safety from accidents in dealing them. Several types of lifting lugs have been used to assemble hundred ton–large steel structures and carry the assembled engines. Recently a few crashes have been occurred in carrying engines due to breaking down the lugs. Although the stability evaluation of the lifting lug has therefore been very important for safety, systematic design procedure of the lugs, which includes the structural analysis considering stability, has few reported. This paper describes the three dimensional finite element structural modeling for a lifting lug, the studies for determining the reasonable loading and boundary conditions, and the stability evaluation with the results of structural analyses. It should be very helpful for designing the other types of lifting lugs with safety.

scholarly journals Effects of placement angle and direction of orthopedic force application on the stability of orthodontic miniscrews

2012 ◽  
Vol 83 (4) ◽  
pp. 667-673 ◽  
Author(s):  
Jihye Lee ◽  
Ji Young Kim ◽  
Yoon Jeong Choi ◽  
Kyung-Ho Kim ◽  
Chooryung J. Chung
Keyword(s):  
Cortical Bone ◽  
Lateral Force ◽  
Von Mises Stress ◽  
Biomechanical Stability ◽  
Element Analysis ◽  
Force Application ◽  
Pull Out ◽  
The Stability ◽  
Von Mises ◽  
Pull Out Strength

ABSTRACT Objectives: To evaluate the influence of placement angle and direction of orthopedic force application on the stability of miniscrews. Materials and Methods: Finite element analysis was performed using miniscrews inserted into supporting bone at angles of 90°, 60°, and 30° (P90°, P60°, and P30°). An orthopedic heavy force of 800 gf was applied to the heads of the miniscrews in four upward (U0°, U30°, U60°, U90°) or lateral (L0°, L30°, L60°, L90°) directions. In addition, pull-out strength of the miniscrews was measured with various force directions and cortical bone thicknesses. Results: Miniscrews with a placement angle of 30° (P30°) and 60° (P60°) showed a significant increase in maximum von Mises stress following the increase in lateral force vectors (U30°, U60°, U90°) compared to those with a placement angle of 90° (P90°). In accordance, the pull-out strength was higher with the axial upward force when compared to the upward force with lateral vectors. Maximum von Mises stress and displacement of the miniscrew increased as the angle of lateral force increased (L30°, L60°, L90°). However, a more dramatic increase in maximum von Mises stress was noted in P30° than in P60° and P90°. Conclusion: Placement of the miniscrew perpendicular to the cortical bone is advantageous in terms of biomechanical stability. Placement angles of less than 60° can reduce the stability of miniscrews when orthopedic forces are applied in various directions.

Numerical Studies of the Effects of Active and Passive Circulation Enhancement Concepts on Wind Turbine Performance

2006 ◽  
Vol 128 (4) ◽  
pp. 432-444 ◽  
Author(s):  
Chanin Tongchitpakdee ◽  
Sarun Benjanirat ◽  
Lakshmi N. Sankar
Keyword(s):  
Wind Speed ◽  
Wind Turbine ◽  
Flow Analysis ◽  
Three Dimensional ◽  
Turbine Rotor ◽  
Horizontal Axis Wind Turbine ◽  
Trailing Edge ◽  
Low Wind Speed ◽  
Gurney Flap ◽  
Coanda Jet

The aerodynamic performance of a wind turbine rotor equipped with circulation enhancement technology (trailing-edge blowing or Gurney flaps) is investigated using a three-dimensional unsteady viscous flow analysis. The National Renewable Energy Laboratory Phase VI horizontal axis wind turbine is chosen as the baseline configuration. Experimental data for the baseline case is used to validate the flow solver, prior to its use in exploring these concepts. Calculations have been performed for axial and yawed flow at several wind conditions. Results presented include radial distribution of the normal and tangential forces, shaft torque, root flap moment, and surface pressure distributions at selected radial locations. At low wind speed (7m∕s) where the flow is fully attached, it is shown that a Coanda jet at the trailing edge of the rotor blade is effective at increasing circulation resulting in an increase of lift and the chordwise thrust force. This leads to an increased amount of net power generation compared to the baseline configuration for moderate blowing coefficients (Cμ⩽0.075). A passive Gurney flap was found to increase the bound circulation and produce increased power in a manner similar to Coanda jet. At high wind speed (15m∕s) where the flow is separated, both the Coanda jet and Gurney flap become ineffective. The effects of these two concepts on the root bending moments have also been studied.

Sign in / Sign up

Export Citation Format

Share Document