Analysis and Numerical Simulation of no Reacting Swirling Flow by Using URANS Approach

2021 ◽  
Vol 57 ◽  
pp. 67-79
Author(s):  
Merouane Habib ◽  
Senouci Mohammed
Keyword(s):  
Experimental Data ◽  
Numerical Simulation ◽  
Swirling Flow ◽  
Navier Stokes ◽  
Governing Equations ◽  
Simulation Based ◽  
Classical Models ◽  
Recirculation Zones ◽  
Computational Fluid Dynamics Cfd ◽  
Volume Method

In this paper, we investigate the no-reacting swirling flow by using the numerical simulation based to the unsteady Reynolds-averaged Navier-Stokes approach. The numerical simulation was realized by using a computational fluid dynamics CFD code. The governing equations are solved by using the finite volume method with two classical models of turbulence K-epsilon and Shear Stress K-ω. The objective of this paper is therefore to evaluate the performance of the two models in predicting the recirculation zones in a swirled turbulent flow. The current models are validated by comparing the numerical results of the axial, radial and tangential velocities to the experimental data from literature.

scholarly journals Three-dimensional numerical simulation of a turbulent flow around an obstacle

2020 ◽  
Vol 307 ◽  
pp. 01006
Author(s):  
Benahmed Lamia ◽  
Aliane Khaled ◽  
Z. Sari Hassoun
Keyword(s):  
Numerical Simulation ◽  
Velocity Field ◽  
Kinetic Energy ◽  
Three Dimensional ◽  
Governing Equations ◽  
Ansys Cfx ◽  
Recirculation Zones ◽  
Rectangular Obstacle ◽  
Volume Method ◽  
Calculation Code

In this work we study the influence of the inclined shape of the lover and downstream edge of a rectangular obstacle. We analyze the dimensions of the recirculation zones, the velocity field, the kinetic energy and the pressure. A three-dimensional study was conducted using the ansys cfx calculation code. The turbulence model k-ԑ is used to model turbulence, and the governing equations are resolved by the finite volume method.

Investigation of Indoor Environment for a Data Center

2009 ◽  
Author(s):  
Lingcang Li ◽  
Yanlei Liu ◽  
Xiuling Wang ◽  
A. G. Agwu Nnanna
Keyword(s):  
Experimental Data ◽  
Numerical Simulation ◽  
Relative Humidity ◽  
Indoor Air ◽  
Data Center ◽  
Indoor Environment ◽  
Low Cost ◽  
Simulation Based ◽  
Simulation Results ◽  
Volume Method

Special indoor air environment requirements are needed for the data center, such as ambient temperature, airflow pattern, relative humidity and ozone concentration to maintain the reliability of a computer system. In this paper, a numerical simulation based on 3-D Finite Volume Method has been conducted for a data center at Purdue University Calumet. The purpose of the simulation is to find out the most effective and low-cost air condition system. Results for temperature, relative humidity distributions as well as velocity patterns are presented. Mesh independent studies are performed. Numerical results are validated by experimental data. Suggestions are given based on the simulation results for improving the indoor environment of the data center.

scholarly journals Scale Effects on a Tip Rake Propeller Working in Open Water

2019 ◽  
Vol 7 (11) ◽  
pp. 404 ◽  
Author(s):  
Lungu
Keyword(s):  
Experimental Data ◽  
Numerical Simulation ◽  
Stokes Equations ◽  
Scale Effects ◽  
Open Water ◽  
Numerical Approach ◽  
Navier Stokes ◽  
Navier Stokes Equations ◽  
Conference Organization ◽  
Volume Method

The scale effect on the accuracy of a numerical simulation in ship hydrodynamics represents an important issue of the propeller numerical analysis. To grasp a better understanding on the influence of this effect, an introspection on the performances of an unconventional propeller is proposed in the present study. The paper describes an investigation of the performances of a tip rake propeller recently chosen as benchmark by the International Towing Tank Conference organization (ITTC hereafter). The numerical simulation is carried out by making use of the ISIS-CFD solver, part of the FineTM/Marine package available in the NUMECA suite. The solver is based on the finite volume method to build the spatial discretization of the governing equations. The incompressible unsteady Reynolds Averaged Navier-Stokes Equations (RANSE) are solved in a global approach. Reported solutions are compared with the experimental data provided by Schiffbau-Versuchsanstalt (SVA) Potsdam GmbH to validate the accuracy of the numerical approach. Since for the full scale the experimental data could not be possible, the ITTC’78 extrapolation method-based proposed by the SVA Potsdam has been taken as a basis for comparisons and discussions. A set of remarks will conclude the paper by providing some guidelines for further approaches in terms of the particulars of the numerics that may be further employed in similar studies.

Flow Field of XCP Probe's Head and Optimization Choice of Structural Parameters

2013 ◽  
Vol 760-762 ◽  
pp. 1753-1757
Author(s):  
Hong Kun He ◽  
Shuang Qi Yang ◽  
Guang Yu Li ◽  
Hong Min Gao
Keyword(s):  
Numerical Simulation ◽  
Flow Field ◽  
Finite Volume Method ◽  
Stokes Equations ◽  
Structural Parameters ◽  
Navier Stokes ◽  
Governing Equations ◽  
Navier Stokes Equations ◽  
Front End ◽  
Volume Method

In this study, numerical simulation of XCP probe was executed. The 3D Navier-Stokes equations were used as governing equations, and the finite volume method combining two-equations turbulence model was applied. The flow field of XCP Probe was analyzed, especially around the XCP Probe's head. The results show that the arc design of the XCP Probe's head plays an important role on the steady falling speed. In addition, when the radian is 27°, the resistance of the probe is smallest and a larger falling speed can be achieved; The electrodes of probe should be located in front end of a conduit which is in the middle of the probe.

Fundamental CFD Study on the Hydrodynamic Performance of the DARPA SUBOFF Submarine

2019 ◽  
Author(s):  
Kenshiro Takahashi ◽  
Prasanta K. Sahoo
Keyword(s):  
Experimental Data ◽  
Hydrodynamic Performance ◽  
Navier Stokes ◽  
Drift Angle ◽  
Computational Fluid Dynamics Cfd ◽  
Cfd Method ◽  
Volume Method ◽  
Straight Ahead ◽  
Reynolds Average ◽  
Multiple Configurations

Abstract This study attempts to examine the potential for computational fluid dynamics (CFD) as an estimation tool of the hydrodynamic performance of submarines. The DARPA SUBOFF model is adopted as a benchmark because of its availability of experimental data for validation. The computational modeling is based on the Reynolds Average Navier Stokes (RANS) equations solved by a finite volume method. Verification and validation of the straight-ahead resistance and the forces and moment exerted on the hull in steady translation and turn with a drift angle were conducted in accordance with the published methodology and procedure. The process to have determined the computational setups is described. Furthermore, the computational results as a function of velocity and drift angle are presented and compared with available experimental data. In conclusion, the present CFD method can be used as an estimation tool for the straight-ahead resistance at various velocities in model scale for multiple configurations.

Analysis of Hydrodynamic Characteristics in the Process of Autonomous Underwater Vehicle Docking

2015 ◽  
Author(s):  
Xiaoxu Du ◽  
Huan Wang
Keyword(s):  
Drag Coefficient ◽  
Autonomous Underwater Vehicle ◽  
Simple Algorithm ◽  
Underwater Vehicle ◽  
Navier Stokes ◽  
Hydrodynamic Characteristics ◽  
Successful Operation ◽  
Underwater Docking ◽  
Computational Fluid Dynamics Cfd ◽  
Volume Method

The successful operation of an Autonomous Underwater Vehicle (AUV) requires the capability to return to a dock. A number of underwater docking technologies have been proposed and tested in the past. The docking allows the AUV to recharge its batteries, download data and upload new instructions, which is helpful to improve the working time and efficiency. During the underwater docking process, unsteady hydrodynamic interference occurs between the docking device and an AUV. To ensure a successful docking, it is very important that the underwater docking hydrodynamics of AUV is understood. In this paper, numerical simulations based on the computational fluid dynamics (CFD) solutions were carried out for a 1.85m long AUV with maximum 0.2 m in diameter during the docking process. The two-dimensional AUV model without fin and rudder was used in the simulation. The mathematical model based on the Reynolds-averaged Navier-Stokes (RANS) equations was established. The finite volume method (FVM) and the dynamic structured mesh technique were used. SIMPLE algorithm and the k-ε turbulence model in the Descartes coordinates were also adopted. The hydrodynamics characteristics of different docking states were analyzed, such as the different docking velocity, the docking device including baffle or not. The drag coefficients of AUV in the process of docking were computed for various docking conditions, i.e., the AUV moving into the docking in the speed of 1m/s, 2m/s, 5m/s. The results indicate that the drag coefficient increases slowly in the process of AUV getting close to the docking device. When the AUV moves into the docking device, the drag coefficient increases rapidly. Then the drag coefficient decreases rapidly. The drag coefficient decreases with the increase of velocity when AUV enters the docking device. It was also found that the drag coefficient can be effectively reduced by dislodging the baffle of docking device.

The Effect of Turbulence and Real Gas Models on the Two Phase Spontaneously Condensing Flows in Nozzle

2013 ◽  
Author(s):  
Yogini Patel ◽  
Giteshkumar Patel ◽  
Teemu Turunen-Saaresti
Keyword(s):  
Fluid Dynamics ◽  
Experimental Data ◽  
Nucleation Theory ◽  
Classical Nucleation Theory ◽  
Navier Stokes ◽  
Two Phase ◽  
Real Gas ◽  
Spontaneous Condensation ◽  
Condensing Flows ◽  
Computational Fluid Dynamics Cfd

The aim of the paper is to analyse the effect of turbulence and real gas models on the process of spontaneous condensation in converging diverging (CD) nozzle by using commercial Computational Fluid Dynamics (CFD) code. The calculations were based on the 2-D compressible Navier-Stokes (NS) equations coupled with two-equation turbulence model, and the non-equilibrium spontaneous condensing steam flow was solved on the basis of the classical nucleation theory. The results were validated to the available experimental data.

scholarly journals OPTIMIZING THE VELOCITY OF RING SHAPE PARAMETER FOR DESIGNING THE NOZZLES USING CFD

2021 ◽  
pp. 1-10
Author(s):  
Obai Younis ◽  
Reem Ahmed ◽  
Ali Mohammed Hamdan ◽  
Dania Ahmed
Keyword(s):  
Shape Parameter ◽  
Maximum Velocity ◽  
Simulation Software ◽  
Governing Equations ◽  
Ansys Fluent ◽  
Ring Shape ◽  
Ring Location ◽  
Computational Fluid Dynamics Cfd ◽  
Triangular Elements ◽  
Volume Method

This study aims to optimize the velocity of ring shape parameter for designing the nozzles using computational fluid dynamics (CFD) and investigated the flow in nozzles using ANSYS, Inc. simulation software. The model geometries were defined using ANSYS FLUENT-Design Modeler platform. All nozzles were designed on unstructured triangular elements comprising of 1200000 mesh nodes. The differential governing equations were applied in ANSYS FLUENT based on a finite volume method. The distance and dimensions of ring location significantly influence the velocity of water during flow where the maximum velocity at double rings reduces the surface area at distance of 7mm and 15mm and 2x2 mm dimensions. Considering 8, 10, and 12 bar liner proportions, there was an increase in the velocity at maximum points in ring shapes.

NUMERICAL PREDICTION OF VERTICAL SHIP MOTIONS AND ADDED RESISTANCE

2021 ◽  
Vol 159 (A4) ◽  
Author(s):  
F Cakici ◽  
E Kahramanoglu ◽  
A D Alkan
Keyword(s):  
Deep Water ◽  
High Speed ◽  
Computer Experiments ◽  
Navier Stokes ◽  
Ship Motions ◽  
Added Resistance ◽  
Strip Theory ◽  
Head Waves ◽  
Computational Fluid Dynamics Cfd ◽  
Volume Method

Along with the development of computer technology, the capability of Computational Fluid Dynamics (CFD) to conduct ‘virtual computer experiments’ has increased. CFD tools have become the most important tools for researchers to deal with several complex problems. In this study, the viscous approach called URANS (Unsteady Reynolds Averaged Navier-Stokes) which has a fully non-linear base has been used to solve the vertical ship motions and added resistance problems in head waves. In the solution strategy, the FVM (Finite Volume Method) is used that enables numerical discretization. The ship model DTMB 5512 has been chosen for a series of computational studies at Fn=0.41 representing a high speed case. Firstly, by using CFD tools the TF (Transfer Function) graphs for the coupled heave- pitch motions in deep water have been generated and then comparisons have been made with IIHR (Iowa Institute of Hydraulic Research) experimental results and ordinary strip theory outputs. In the latter step, TF graphs of added resistance for deep water have been generated by using CFD and comparisons have been made only with strip theory.

Numerical Prediction of Vertical Ship Motions and Added Resistance

2017 ◽  
Vol 159 (A4) ◽  
Author(s):  
F Cakici ◽  
E Kahramanoglu ◽  
A D Alkan
Keyword(s):  
Deep Water ◽  
High Speed ◽  
Computer Experiments ◽  
Navier Stokes ◽  
Ship Motions ◽  
Added Resistance ◽  
Strip Theory ◽  
Head Waves ◽  
Computational Fluid Dynamics Cfd ◽  
Volume Method

Along with the development of computer technology, the capability of Computational Fluid Dynamics (CFD) to conduct ‘virtual computer experiments’ has increased. CFD tools have become the most important tools for researchers to deal with several complex problems. In this study, the viscous approach called URANS (Unsteady Reynolds Averaged Navier-Stokes) which has a fully non-linear base has been used to solve the vertical ship motions and added resistance problems in head waves. In the solution strategy, the FVM (Finite Volume Method) is used that enables numerical discretization. The ship model DTMB 5512 has been chosen for a series of computational studies at Fn=0.41 representing a high speed case. Firstly, by using CFD tools the TF (Transfer Function) graphs for the coupled heave-pitch motions in deep water have been generated and then comparisons have been made with IIHR (Iowa Institute of Hydraulic Research) experimental results and ordinary strip theory outputs. In the latter step, TF graphs of added resistance for deep water have been generated by using CFD and comparisons have been made only with strip theory.

Sign in / Sign up

Export Citation Format

Share Document