Cyclic Behavior of Electrical Resistance Type Low Stiffness, Large Strain Sensor by Using Carbon Nanofiber/Flexible Epoxy Composite

2011 ◽  
Vol 462-463 ◽  
pp. 1200-1205 ◽  
Author(s):  
Yoshinobu Shimamura ◽  
Kyohei Kageyama ◽  
Keiichiro Tohgo ◽  
Tomoyuki Fujii
Keyword(s):  
Electrical Conductivity ◽  
Electrical Resistance ◽  
Carbon Nanofiber ◽  
Epoxy Composite ◽  
Large Strain ◽  
Conductive Polymer ◽  
Cyclic Behavior ◽  
Resistance Change ◽  
Sensing Applications ◽  
Electrical Resistance Change

Carbon nanofiber (CNF) has good electrical conductivity. Addition of a few percentages of carbon nanofiber to polymer yields electrical conductivity but hardly affects the mechanical properties of polymer. This conductive polymer may be useful for sensing applications such as strain sensors and chem-resist sensors. Many researchers have reported on the electrical conductivity, but the electrical resistance change under strain of the carbon nanofiller composites is not fully investigated. In this study, the electrical resistance change under strain of CNF/flexible-epoxy composites was investigated experimentally. More than 100% of quasi-static strain can be measured by using CNF/flexible-epoxy composite with Young’s modulus of less than 1MPa. Cyclic and unloading behaviors were also measured and discussed. It was found that the cyclic behavior was strongly affected by viscoelasticity and damage.

Assessing the Stability of Inkjet-Printed Carbon Nanotube for Brine Sensing Applications

2020 ◽  
Vol 20 (12) ◽  
pp. 7644-7652
Author(s):  
Khalid Marbou ◽  
Waqas Gil ◽  
Amal Al Ghaferi ◽  
Irfan Saadat ◽  
Khalid Alhammadi ◽  
...  
Keyword(s):  
Electrical Resistance ◽  
Electrochemical Sensors ◽  
Sessile Drop ◽  
Synthesis Methods ◽  
Resistance Change ◽  
Sensing Applications ◽  
The Stability ◽  
The Impact ◽  
Oil Gas ◽  
Electrical Resistance Change

In hostile environments, sensing is critical for many industries such as chemical and oil/gas. Within this industry, the deposition of scales or minerals on various infrastructure components (e.g., pipelines) forms a reliability hazard that needs to be monitored. Therefore, the approach adopted in this study to tackle this issue relies on the use of real-time sensing of specific ions in brine, the natural trigger for ions deposition. In order to do so, electrochemical sensors based on carbon nanotubes (CNTs) are developed, taking advantage of their unique properties facilitated by different synthesis and fabrication methods. One of these promising synthesis methods is inkjet printing of CNT films since in general, it has exceptional benefits over other approaches that are used to print CNTs. Furthermore, it does not need the use templates. In addition, it is a very fast technique with consistent printing results for many applications along with very low cost on various shapes/formfactors. As these sensors are exposed to a hostile environment (chemical, temperature, etc.), the stability of the CNT films is of great importance. In this study, a comprehensive investigation of the stability of CNT surfaces upon exposure to elements is presented. Accordingly, the several impacts of this interaction on physical properties of the surfaces as a function of interaction time and brine chemical composition are assessed. Moreover, the approach used for investigating the impact of this exposure involves the following: surface electrical resistance change using four probe measurements; surface roughness/topography using Atomic Force Microscopy (AFM) along Scanning Electron Microscopy (SEM); quality of CNT through Raman spectroscopy and wettability using the sessile drop method. The sensing capabilities of the devices are investigated by looking at the sensing selectivity of target ions, resetting capabilities, and sensing sensitivity manifested in the electrical resistance change. Consequently, our results indicate that while inkjet films are very promising sensor material, the fabrication and long term stability require further optimization of the films along with the process to make them meet reliability and lifetime requirements in the oil/gas hostile operational environments.

Electrical Resistance Change under Strain of CNF/Flexible-Epoxy Composite

2010 ◽  
Vol 19 (2) ◽  
pp. 123-138 ◽  
Author(s):  
Tetsuo Yasuoka ◽  
Yoshinobu Shimamura ◽  
Akira Todoroki
Keyword(s):  
Electrical Resistance ◽  
Epoxy Composite ◽  
Resistance Change ◽  
Electrical Resistance Change

Electrical Failure and Damage Analysis of Multi-Layer Metal Films on Flexible Substrate during Cyclic Bending Deformation

2011 ◽  
Author(s):  
Byoung-Joon Kim ◽  
Hae-A-Seul Shin ◽  
In-Suk Choi ◽  
Young-Chang Joo
Keyword(s):  
Fatigue Resistance ◽  
Electrical Resistance ◽  
Metal Film ◽  
Flexible Substrate ◽  
Resistance Change ◽  
Cyclic Bending ◽  
Capping Layer ◽  
Bending Strain ◽  
Cu Film ◽  
Electrical Resistance Change

Abstract The electrical resistance Cu film on flexible substrate was investigated in cyclic bending deformation. The electrical resistance of 1 µm thick Cu film on flexible substrate increased up to 120 % after 500,000 cycles in 1.1 % tensile bending strain. Crack and extrusion were observed due to the fatigue damage of metal film. Low bending strain did not cause any damage on metal film but higher bending strain resulted in severe electrical and mechanical damage. Thinner film showed higher fatigue resistance because of the better mechanical property of thin film. Cu film with NiCr under-layer showed poorer fatigue resistance in tensile bending mode. Ni capping layer did not improve the fatigue resistance of Cu film, but Al capping layer suppressed crack formation and lowered electrical resistance change. The NiCr under layer, Ni capping layer, and Al capping layer effect on electrical resistance change of Cu film was compared with Cu only sample.

Sign in / Sign up

Export Citation Format

Share Document