Composition Development and Production Technology of Stone Casting Silicate Materials and Items

2017 ◽  
Vol 743 ◽  
pp. 401-405 ◽  
Author(s):  
Arseny O. Artemov ◽  
Michael N. Ignatov ◽  
Anna M. Ignatova ◽  
Stanislav V. Naumov

Though silicate-oxide materials are in demand in all industries, inclusive of defense industry, their application is limited by manufacturing capability of their formation. Therefore, range expansion of manufacturing capability of forming silicate-oxide materials is an important issue. Casting technology allows obtaining fair-sized items and composite pattern at lower cost. It is used for silicate-oxide materials in petrurgical (stone casting) manufacturing, the melt for stone casting technology being often received by electric arc method.

2017 ◽  
Vol 265 ◽  
pp. 1148-1151 ◽  
Author(s):  
Arseny O. Artemov ◽  
Michael N. Ignatov ◽  
Anna M. Ignatova

Study and description of positive effect influence of Cr2O3 catalyst in controlled crystallization technology for production of stone casting silicate materials are provided. The introduction of heat treatment method that influences the forming of the structural components of produced material. The basis of manufacturing stone casting silicate materials is controlled crystallization of silicate melt that is organized in such a way that nucleation occurs within the melt and the final product has a fine grain structure. The structural components of silicate stone casting materials and their influence on strength properties are determined. The strength of stone casting silicate materials is the reduction in the difference in the temperature coefficients of linear expansion of crystal phases and residual glass phase.


2020 ◽  
Vol 120 ◽  
pp. 196-210
Author(s):  
L. L. Bragina ◽  
S. O. Ryabinin ◽  
O. Yu. Fedorenko ◽  
O. P. Degurko ◽  
S. O. Melnik

A review of foreign and native publications on the use of man-made raw materials, which is formed during the extraction and processing of rocks, in the silicate materials production was presented. It was shown that, the disposal of large-scale industrial waste from mining and ore processing industrial complexes is promising for solving environmental problems and expanding the raw material base of silicate industries. An increase in the waste consumption degree will contribute to the integrated use of mineral raw materials, as well as a decrease in the volume of their accumulation and an improvement in the environmental situation. A literature review has shown the obvious potential of waste as an alternative raw material for partial or complete replacement of traditional raw materials in various silicate industries. On the example of artificial stone, stone casting, cement, concrete, ceramic bricks and tiles production, the technologies of silicate materials and products were considered, where waste disposal is technologically sound and economically feasible. It was shown that, mineral technogenic raw materials (wastes from mining, mechanical processing and enrichment of rocks) are used as a concrete, artificial stone and other composite binder’s filler, as non-plastic and fluxing components of ceramics bodies, and even as the main raw material in the production of stone casting. On specific examples, it was considered how a reasonable rocks waste use in the silicate materials production can improve the products properties. Requirements were formulated and criteria for the applicability of stone mining and stone processing waste in the silicate materials production were determined, consideration of which will reduce the hazards and risks associated with the possible presence of technologically harmful and potentially hazardous substances in waste. Knowledge of the using peculiarities wastes from the extraction and processing of the different rocks will allow to optimize technological processes when replacing natural raw materials with technogenic materials. Providing scientific and technical information on the advantages of using waste in the ceramic, glass-crystalline, binders and composite materials production will contribute to the development of resource-saving environmentally friendly technologies, natural resources rational use and increase of industrial enterprises responsibility to society and nature.


2018 ◽  
Vol 918 ◽  
pp. 34-39
Author(s):  
Marie Moses ◽  
Claudia Kawalla ◽  
Rudolf Kawalla ◽  
Michael Höck

In order to meet customer requirements, technology developments need to stay focused at process rationalization and quality improvements. Combining the twin-roll casting technology and caliber rolling technology for magnesium wire, customer demands concerning cost-efficiency and high quality can be satisfied. The resulting long products can be applied in the automotive industry and aircraft sector as joining and welding elements or in biomedicine as screws. For this purpose, the paper analyzes potential application fields and their induced quality properties. Special requirements of illustrative magnesium long products are shown by adapting existing requirements of aluminum wire. Finally, the innovative magnesium wire production technology will be explained and the advantages, in particular the resource efficiency, of the developed technology will be discussed.


Author(s):  
J. R. Porter ◽  
J. I. Goldstein ◽  
D. B. Williams

Alloy scrap metal is increasingly being used in electric arc furnace (EAF) steelmaking and the alloying elements are also found in the resulting dust. A comprehensive characterization program of EAF dust has been undertaken in collaboration with the steel industry and AISI. Samples have been collected from the furnaces of 28 steel companies representing the broad spectrum of industry practice. The program aims to develop an understanding of the mechanisms of formation so that procedures to recover residual elements or recycle the dust can be established. The multi-phase, multi-component dust particles are amenable to individual particle analysis using modern analytical electron microscopy (AEM) methods.Particles are ultrasonically dispersed and subsequently supported on carbon coated formvar films on berylium grids for microscopy. The specimens require careful treatment to prevent agglomeration during preparation which occurs as a result of the combined effects of the fine particle size and particle magnetism. A number of approaches to inhibit agglomeration are currently being evaluated including dispersal in easily sublimable organic solids and size fractioning by centrifugation.


Author(s):  
M.E. Rosenfeld ◽  
C. Karboski ◽  
M.F. Prescott ◽  
P. Goodwin ◽  
R. Ross

Previous research documenting the chronology of the cellular interactions that occur on or below the surface of the endothelium during the initiation and progression of arterial lesions, primarily consisted of descriptive studies. The recent development of lower cost image analysis hardware and software has facilitated the collection of high resolution quantitative data from microscopic images. In this report we present preliminary quantitative data on the sequence of cellular interactions that occur on the endothelium during the initiation of atherosclerosis or vasculitis utilizing digital analysis of images obtained directly from the scanning electron microscope. Segments of both atherosclerotic and normal arteries were obtained from either diet-induced or endogenously (WHHL) hypercholesterolemic rabbits following 1-4 months duration of hypercholesterolemia and age matched control rabbits. Vasculitis was induced in rats following placement of an endotoxin soaked thread adjacent to the adventitial surface of arteries.


2003 ◽  
Vol 112 ◽  
pp. 717-719
Author(s):  
V. N. Slipchenko ◽  
Yu. N. Koval ◽  
O. V. Koshovy

Sign in / Sign up

Export Citation Format

Share Document