Photocatalytically Active Cotton Fabrics Produced with Anatase Synthesized Using a Low-Temperature Sol-Gel Process

2018 ◽  
Vol 762 ◽  
pp. 408-412
Author(s):  
Raivis Eglītis ◽  
Gundars Mežinskis
Keyword(s):  
Photocatalytic Activity ◽  
Uv Light ◽  
Sol Gel ◽  
Average Particle Size ◽  
Synthesis Method ◽  
Average Particle ◽  
X Ray Diffraction ◽  
Sol Gel Process ◽  
Anatase Nanoparticles ◽  
Pre Treatment

In this work two different hydrosols were used to impregnate a commercially available cotton fabric with anatase nanoparticles to give it photocatalytic activity. To increase the activity, different pre-treatment methods were applied. The nanoparticle size was determined using dynamic light scattering and x-ray diffraction and the fabrics were examined using scanning electron microscopy. Photocatalytic activity was measured using the degradation of methyl-orange while irradiating the samples with UV light. The synthesis method allowed to produce anatase with an average particle size of 32 to 37 nm depending on the synthesis method used.

Characterization and Photocatalytic Activity of SmMnO3 Prepared by Sol-Gel Process

2017 ◽  
Vol 748 ◽  
pp. 403-407
Author(s):  
Jia Yuan Min ◽  
Long Long Yu ◽  
Pei Song Tang ◽  
Hai Feng Chen
Keyword(s):  
Photocatalytic Activity ◽  
Methyl Orange ◽  
Uv Light ◽  
Raw Materials ◽  
Sol Gel ◽  
Average Particle Size ◽  
High Photocatalytic Activity ◽  
Average Particle ◽  
Nitrate Hexahydrate ◽  
Sol Gel Process

Using samarium (III) nitrate hexahydrate, manganese nitrate and citric acid as main raw materials, the SmMnO3 gel was prepared by sol-gel process. The gel was kept at 100 °C for 24 h to get the xerogel. Then, the xerogel was respectively calcined in muffle furnace at 600 °C, 700 °C, 800 °C and 900 °C. The structure and morphology of samples were characterized by powder X-ray diffraction (XRD), scanning electron microscopy (SEM) and Fourier Transform Infrared (FT-IR) spectroscopy. The UV photocatalytic activities of SmMnO3 were investigated by methyl orange which was used as simulated sewage. The results show that the pure SmMnO3 can be obtained through calcination between 700 °C and 800 °C, and the SmMnO3 have an average particle size of 80 nm. The SmMnO3 samples calcined at 700 °C and 800 °C show high photocatalytic activity for decomposition of methyl orange under UV-light irradiation. The SmMnO3 samples are consistent with first-order kinetics for the degradation of methyl orange. And the apparent rate constants are respectively k700 =0.01206 min-1and k800=0.01088 min-1.

A Calcination Technology for Ultrafine La3NbO7 Powder Prepared by Sol-Gel Process

2011 ◽  
Vol 412 ◽  
pp. 271-274
Author(s):  
Ying Li ◽  
Qiang Xu ◽  
Ling Dai
Keyword(s):  
Single Phase ◽  
Sol Gel ◽  
Average Particle Size ◽  
Complex Method ◽  
Average Particle ◽  
X Ray Diffraction ◽  
Scanning Calorimetry ◽  
Acid Complex ◽  
Calcination Process ◽  
Sol Gel Process

In order to prepare ultrafine La3NbO7 powder, a potential material for thermal barrier coatings, the calcination process of La3NbO7 was studied in this paper.The precursor of La3NbO7 was synthesized by using a citric acid complex method. A calcination process had been systematically investigated. The reaction temperature was determined by differential scanning calorimetry (DSC). The phase composition of powders was characterized by X-ray diffraction (XRD), and the morphology was obtained by scanning electron microscope (SEM). The results revealed that the single-phase La3NbO7 powder could be successfully prepared while the calcination temperature exceeded 800°C and a better morphology could be maintained at 800°C for 4 hours. Considering all above, an optimum calcination scheme was adopted at 800°C for 4 hours. The as-prepared La3NbO7 powders had a grain size of about 50nm and an average particle size of about 300nm.

scholarly journals Fabrication and characterisation of Fe2O3/chitosan aerogel-like spheres

2021 ◽  
Vol 10 (1) ◽  
pp. 74-78
Author(s):  
Nhan Dang Thi Thanh ◽  
Don Truong Thi ◽  
Thang Le Quoc ◽  
Tien Tran Dong ◽  
Son Le Lam
Keyword(s):  
High Surface ◽  
Sol Gel ◽  
Average Particle Size ◽  
High Surface Area ◽  
Hollow Structure ◽  
Average Particle ◽  
X Ray Diffraction ◽  
Factors Affecting ◽  
Sol Gel Process ◽  
High Surface Area Materials

Presently, biopolymer materials have been given more attention for their outstanding properties, high efficiencies and promising applications in various fields. In this study, Fe2O3/chitosan aerogel-like spheres were successfully prepared from chitosan and FeCl3 by sol–gel process and freeze-drying to provide high-surface area materials. The factors affecting the material synthesis have been studied. The asprepared Fe2O3/chitosan material was characterized by Infrared Spectroscopy (IR), X-ray diffraction (XRD) and Scanning Electron Microscopy (SEM) methods. The results showed that the aerogel spheres have a hollow structure made of chitosan nanofibril networks. Fe2O3 nanoparticles get high crystallinity and have an average particle size of 33 nm.

The Preparation and Photocatalytic Activity of SWNTs Doped ZnO/TiO2 Compound Films

2010 ◽  
Vol 97-101 ◽  
pp. 1611-1615 ◽  
Author(s):  
Qing Wang ◽  
Xin Li Li ◽  
Wei Nie ◽  
Yong Mei Xia ◽  
Jian Feng Dai
Keyword(s):  
Photocatalytic Activity ◽  
Absorption Spectra ◽  
Sol Gel ◽  
Composite Films ◽  
Wavelength Region ◽  
Tio2 Films ◽  
X Ray Diffraction ◽  
Sol Gel Process ◽  
Doped Zno ◽  
Walled Carbon Nanotubes

The ZnO/TiO2 composite films were deposited over glass using spin coating technique by sol-gel process. Single-walled carbon nanotubes (SWNTs) were used to modify the ZnO/TiO2 films successfully in this paper. The structure and composition of the ZnO/TiO2 composite and SWNTs doped ZnO/TiO2 composite were characterized by X-ray diffraction (XRD). The morphology of samples was characterized by scanning electron microscopy (SEM). The photocatalytic activity was investigated by photocatalytic degradation of aqueous methyl orange under ultraviolet (UV) radiation. The UV-vis absorption spectra of the ZnO/TiO2 films and SWNTs doped ZnO/TiO2 films in the wavelength region 200~800 nm were obtained. The results indicate that the SWNTs addition can decrease the grain size of ZnO/TiO2, which can enhance the photocatalytic activity. UV-vis absorption spectra of SWNTs-ZnO/TiO2 showed obvious blue shifts compared with ZnO/TiO2. The optimal amount of doping SWNTs is 1% according to this research. The enhanced mechanism of the SWNTs for the photocatalytic activity in ZnO/TiO2 films was analyzed in this article.

Nanocrystalline α-Fe2O3: A Superparamagnetic Material for w-LED Application and Waste Water Treatment

2021 ◽  
Author(s):  
Mahesh Gaidhane ◽  
Deepak Taikar ◽  
Pravin Gaidhane ◽  
Kalpana Nagde
Keyword(s):  
Photocatalytic Activity ◽  
Waste Water Treatment ◽  
Sol Gel ◽  
Average Particle Size ◽  
Emission Spectra ◽  
Broad Emission Band ◽  
Average Particle ◽  
X Ray ◽  
Prepared Material ◽  
Cie Chromaticity

Abstract Nanocrystalline α-Fe2O3 is synthesized by sol-gel technique. The prepared nanomaterial was characterized by X-ray diffraction (XRD), SEM, TEM, Fourier Transform Infrared (FTIR) spectroscopy, Vibrating Sample Magnetometry (VSM) and photoluminescence (PL) techniques. X-ray powder diffraction analysis confirmed the formation of α-Fe2O3. Electron microscopy showed spherical morphologies with an average particle size of 30-40 nm. The magnetic property of the prepared material was studied by VSM at room temperature. VSM study shows superparamagnetic nature of the synthesized nanoparticles. Photoluminescence (PL) emission spectra show intense broad emission band centered at 570 nm with 393 nm excitation indicating its usefulness for w-LED application. The CIE-chromaticity color coordinates of prepared material were calculated. The photocatalytic activity of the α-Fe2O3 nanoparticles was analyzed and the nanopowder exhibited good photocatalytic activity for the removal AO7 from its aqueous solution.

Preparation of Nano-TiO2 Using a Sol-Gel Process Mediated in Reverse Microemulsion Combined with a Solvent Thermal Technique

2011 ◽  
Vol 287-290 ◽  
pp. 1731-1734 ◽  
Author(s):  
Han Sheng Li ◽  
Hang Xu ◽  
Shi Ying Wang ◽  
Ya Lin Pan ◽  
Qin Wu ◽  
...  
Keyword(s):  
Sol Gel ◽  
Average Particle Size ◽  
High Photocatalytic Activity ◽  
Reverse Microemulsion ◽  
Molar Ratio ◽  
Average Particle ◽  
Anatase Structure ◽  
Sol Gel Process ◽  
Triton X ◽  
Thermal Technique

Anatase nano-titania (nano-TiO2) was prepared by using a sol-gel process mediated in reverse microemulsion combined with a solvent thermal technique. The results show that the anatase structure appears in the calcination temperature range of 400-510°C, while the transformation of anatase into rutile takes place above 510°C. The average particle size (dP) of the nano-TiO2 increases with the rise of water/Triton X-100 molar ratio (ω) but decreases with the rise of acetyl acetone/n-TBT molar ratio (p) and n-hexanol/Triton X-100 molar ratio (m). The obtained TiO2 particles with a small size have high photocatalytic activity.

Pb2+ and Ce3+ Doped SrZnO2: New Blue Luminescent Phosphors

2006 ◽  
Vol 916 ◽  
Author(s):  
Alp Manavbasi ◽  
Jeffrey C LaCombe
Keyword(s):  
Sol Gel ◽  
Average Particle Size ◽  
Broad Band ◽  
Emission Spectra ◽  
Broad Emission Band ◽  
Average Particle ◽  
X Ray Diffraction ◽  
Broad Emission ◽  
Diffraction Patterns ◽  
Individual Particles

AbstractTwo new blue emitting phosphors, SrZnO2:Pb2+ and Ce3+ were synthesized by adipic acid and sucrose templated sol-gel routes, respectively. The resulting phosphor particles were fine, nanocrystalline and pure. The optimum activator concentrations were found to be 1 mol% Pb2+ and 12 mol% Ce3+. Two excitation bands centered at 283 and 317 nm, plus a weak shoulder at 275 nm were observed for Pb2+ doped samples, however only one broad excitation band with a maximum at 294 nm was observed for Ce3+ doped samples fired at 1000 °C for 2h. The emission spectra of SrZnO2:Pb2+ showed a very broad band extending from 374 to 615 nm with a maximum at ~455 nm which was ascribed to the 3P1 ¡æ 1S0 transition on the Pb2+ ions allowed by the strong spin-orbit (SO) coupling. Similarly, SrZnO2:Ce3+ showed a broad emission band extending from 374 to 609 nm and centered at 467 nm. This broad emission was attributed to the 5d1 ¡æ 4f1 transition of Ce3+ ions. The lower level 2F5/2 of the 4f1 is populated but the level 2F7/2 is almost empty at room temperature where all measurements were taken. The luminescence properties of Ce3+, K+ co-doped SrZnO2 revealed that the characteristic band locations remained the same and the ratio of emission to excitation intensities were constant. X-ray diffraction patterns showed that the SrZnO2 phase started to form at 900 °C (after 2 hrs), and the single-phase SrZnO2 obtained at 1000 °C. SEM micrographs of both phosphors have a rounded and filled morphology for individual particles with an approximate diameter of 50-250 nm. Dynamic light scattering studies revealed that average particle size is around 1 ¥ìm for both phosphors.

Porous Ceramic Humidity Sensors Using Sol-Gel Processed ZrTiO4 Nanoparticles

2006 ◽  
Vol 45 ◽  
pp. 1803-1808 ◽  
Author(s):  
I.C. Cosentino ◽  
E.N.S. Muccillo ◽  
F.M. Vichi ◽  
R. Muccillo
Keyword(s):  
Porous Ceramic ◽  
Mercury Porosimetry ◽  
Sol Gel ◽  
Average Particle Size ◽  
Nitrogen Adsorption ◽  
Zirconium Oxychloride ◽  
Average Particle ◽  
Titanium Tetraisopropoxide ◽  
X Ray Diffraction ◽  
Adsorption Analysis

Ceramic ZrTiO4 powders were prepared by a sol-gel method using zirconium oxychloride and titanium tetraisopropoxide. In situ high temperature X-ray diffraction results show that crystallization of the amorphous gel starts at 400°C. Single-phase ZrTiO4 nanoparticles of 46 nm average particle size, determined by nitrogen adsorption analysis, were obtained after heat treatment at 450°C for 1 h. After pressing these sinteractive powders, pellets with controlled pore size distribution were obtained by sintering at temperatures as low as 400°C. The analysis of pores by mercury porosimetry gives an average porosity of 45%. The electrical resistivity, determined by impedance spectroscopy measurements at 24°C under different humidity environments, shows the ability of these pellets to adsorb water vapor in the porous surfaces.

scholarly journals Preparation and Photocatalytic Activity of TiO2/Fine Char for Removal of Rhodamine B

2015 ◽  
Vol 2015 ◽  
pp. 1-5 ◽  
Author(s):  
Mingjie Ma ◽  
Weijie Guo ◽  
Zhengpeng Yang ◽  
Shanxiu Huang ◽  
Guanyu Wang
Keyword(s):  
Photocatalytic Activity ◽  
Photocatalytic Degradation ◽  
Rhodamine B ◽  
Uv Light ◽  
Sol Gel ◽  
Tetrabutyl Titanate ◽  
Light Illumination ◽  
X Ray Diffraction ◽  
X Ray ◽  
Uv Light Irradiation

TiO2/fine char (FC) photocatalyst was prepared via sol-gel method with tetrabutyl titanate as the precursor and FC as the carrier. The structural property of TiO2/FC photocatalyst was investigated by X-ray diffraction (XRD) and scanning electron microscopy (SEM), and the photocatalytic activity of TiO2/FC was evaluated by photocatalytic degradation of rhodamine B (RhB) aqueous solution under UV light irradiation. The results showed that TiO2was successfully coated on the surface of FC, and the TiO2/FC photocatalyst had better photocatalytic efficiency and stability for degradation of RhB under UV light illumination as compared to that of the pure TiO2and FC. The study provided a novel way for the application of FC to the photocatalytic degradation of organic wastes.

Effect of Fe Incorporation on the Photocatalytic Activity of TiO2 by Sol-Gel Method

2015 ◽  
Vol 1087 ◽  
pp. 218-222
Author(s):  
Siti Aida Ibrahim ◽  
Srimala Sreekantan
Keyword(s):  
Photocatalytic Activity ◽  
Uv Light ◽  
Sol Gel ◽  
Combination Method ◽  
X Ray Diffraction ◽  
X Ray ◽  
Uv Light Irradiation ◽  
Vis Spectroscopy ◽  
Visible Irradiation ◽  
Emission Microscopy

Nanostructured Fe-TiO2 and TiO2 with anatase structure were synthesized via combination method of sol-gel and peptization process. The samples were characterized by X-ray diffraction (XRD), Transmission emission microscopy (TEM) and UV-Vis spectroscopy (UV-Vis). The presence of Fe3+ ion shifted the absorption profile of TiO2 to the longer wavelength side of the spectrum, indicating an obvious photocatalytic activity under visible irradiation. Photocatalytic activity of the samples were evaluated by methyl orange (MO) discolouration under UV-light irradiation. Compared with the pure TiO2 nanoparticles, the Fe-TiO2 nanoparticles exhibited higher photocatalytic activity with 95% discoloration within 2 h.

Sign in / Sign up

Export Citation Format

Share Document