Numerical Simulation of Residual Stress in P91 Repair Welding Incorporating Martensitic Transformation

2019 ◽  
Vol 795 ◽  
pp. 416-423
Author(s):  
Ze Xun Hu ◽  
Jian Ping Zhao ◽  
Ying Jie Zhang
Keyword(s):  
Residual Stress ◽  
Martensitic Transformation ◽  
Latent Heat ◽  
Service Failure ◽  
Repair Welding ◽  
Type Iv ◽  
Strength Change ◽  
Element Simulation ◽  
Area Increase ◽  
Type Iv Cracking

The type IV cracking is one of the main reasons for service failure. The repair welding is implemented to solve this problem. The residual stress in P91 repair welding incorporating martensitic transformation (MT) is acquired through finite element simulation. In the simulation, the ABAQUS and the user subroutines FILM, DFLUX, HETVAL, USDFLD, UEXPAN and UHARD are adopted. The effect of MT latent heat on temperature and the effects of the volume expansion, the yield strength change and the transformation plasticity on stress are considered. The results show that there is full MT in the repair welding area and the old welding area. The MT latent heat makes the temperature of the repair welding area increase. The residual stress of the repair welding area decreases because MT relieves the thermal stress. Before repair welding, the residual stress distribution is M-shape, which is consistent with the experimental results. After repair welding, the residual stress of repair welding area decreases and the residual stress of old welding area increases.

Study on Welding Deformation and Residual Stress of H-Section Beam Based on Finite Element Method

2017 ◽  
Vol 753 ◽  
pp. 305-309 ◽  
Author(s):  
Xu Lu
Keyword(s):  
Mechanical Properties ◽  
Residual Stress ◽  
Finite Element ◽  
Source Parameters ◽  
Welding Process ◽  
Steel Structure ◽  
Bottom Plate ◽  
Welding Deformation ◽  
Element Simulation ◽  
Main Components

The welding H-section beam has good mechanical properties with its superior structure. So they become the main components of steel structure and have been widely used. In this paper, the welded H-section beam is used as the research object. The finite element simulation model is established. The heat source parameters are determined. The deformation of the steel due to the welding process is studied. The results show that the bottom plate and the bottom plate inward bending is about 2.32mm cause by welding process. The residual stress can reach 400MPa.

STRUCTURAL AND MARTENSITIC TRANSFORMATION OF BULK, DISORDERED AND NANOCRYSTALLINE Ni2MnGa ALLOYS

2011 ◽  
Vol 04 (04) ◽  
pp. 415-418 ◽  
Author(s):  
K. VALLAL PERUMAN ◽  
S. VINODH KUMAR ◽  
K. PUSHPANATHAN ◽  
M. MAHENDRAN
Keyword(s):  
Residual Stress ◽  
Differential Scanning Calorimetry ◽  
Martensitic Transformation ◽  
Tetragonal Phase ◽  
Hysteresis Curve ◽  
Nanosized Particles ◽  
Bulk Alloy ◽  
Scanning Calorimetry ◽  
Disordered Phase ◽  
Annealing Method

Ferromagnetic Ni2MnGa nanoparticles were prepared by post milling and annealing method. Differential scanning calorimetry studies confirm absence of martensitic and Curie transformation in the disordered state. It was found that the bulk alloy was annealed into a well-defined 7 M structure at around 1073 K. The residual stress of nanoparticles induced the disordered phase to transform into a NM tetragonal phase through atomic ordering. Thermo hysteresis curve of the 'disordered' powder was linear and revealed very low moment indicative of paramagnetic nature. It is confirmed that the martensitic transformation in nanosized particles is predominantly dependent on the strain and the particles size.

scholarly journals Development of Welding P92 Pipes Using the Reduced Pressure Electron Beam Welding Process for a Study of Creep Performance

2014 ◽  
Author(s):  
Nick Bagshaw ◽  
Chris Punshon ◽  
John Rothwell
Keyword(s):  
Electron Beam ◽  
Heat Input ◽  
Power Plants ◽  
Electron Beam Welding ◽  
Welding Process ◽  
Welding Parameters ◽  
Pipe Material ◽  
Reduced Pressure ◽  
Type Iv ◽  
Type Iv Cracking

Boiler and steam piping components in power plants are fabricated using creep strength enhanced ferritic (CSEF) steels, which often operate at temperatures above 550°C. Modification of alloy content within these steels has produced better creep performance and higher operating temperatures, which increases the process efficiency of power plants. The improved materials, however, are susceptible to type IV cracking at the welded regions. A better understanding of type IV cracking in these materials is required and is the basis of the Technology Strategy Board (TSB) UK funded VALID (Verified Approaches to Life Management & Improved Design of High Temperature Steels for Advanced Steam Plants) project. In order to study the relationship between creep performance and heat input during welding, several welds with varying amounts of heat input and resultant HAZ widths were produced using the electron beam welding process. The welding parameters were developed with the aid of weld process modeling using the finite element (FE) method, in which the welding parameters were optimized to produce low, medium and high heat input welds. In this paper, the modeling approach and the development of electron beam welds in ASTM A387 grade P92 pipe material are presented. Creep specimens were extracted from the welded pipes and testing is ongoing. The authors acknowledge the VALID project partners, contributors and funding body: Air Liquide, Metrode, Polysoude, E.ON New Build & Technology Ltd, UKE.ON, Doosan, Centrica Energy, SSE, Tenaris, TU Chemnitz, The University of Nottingham, The Open University and UK TSB. Paper published with permission.

Creep Damage Evaluation of Fine-Grained HAZ in Mod. 9Cr Ferritic Heat-Resistant Steel Weldments

2007 ◽  
Author(s):  
N. Yoneyama ◽  
K. Kubushiro ◽  
H. Yoshizawa
Keyword(s):  
Creep Damage ◽  
Life Time ◽  
Creep Life ◽  
Creep Tests ◽  
Boundary Density ◽  
Fine Grained ◽  
Type Iv ◽  
Fine Grain ◽  
Type Iv Cracking ◽  
Rupture Mechanism

9Cr steel weldments are concerned with evaluation of creep life time and creep rupture mechanism. In fine grain HAZ (FG-HAZ) of weldments, TYPE IV cracking and creep voids occurred at lower stress than rupture stress level of base metal. In the crept specimen, FG-HAZ sometime has large coarsening grains near creep voids. These recovery phenomena are localized in FG-HAZ, and recovered microstructures are dependent on heat input of welding. In this study, creep tests are examined in two types of weldments, and relations between creep life time and coarsened sub-grains or grains have been studied by microstructural changing with EBSP analysis. In crept specimens, boundaries are moved and boundary density is decreasing in the fine-grained HAZ. Maximum grain size and creep life time have linear function, and EBSP can evaluate creep life time of 9Cr weldments. These microstructural changing are considered by morphology of precipitates in the several crept specimens.

Experimental Analysis of Repair Welding Alternatives for Shipbuilding DH36 Plates

2020 ◽  
Vol 64 (04) ◽  
pp. 384-391
Author(s):  
Tetyana Gurova ◽  
Segen F. Estefen ◽  
Anatoli Leontiev ◽  
Plinio T. Barbosa ◽  
Valentin Zhukov ◽  
...  
Keyword(s):  
Residual Stress ◽  
Stress Distribution ◽  
Best Practice ◽  
Welding Process ◽  
Offshore Structures ◽  
Residual Stress Distribution ◽  
Shipbuilding Industry ◽  
Repair Welding ◽  
Ship Construction ◽  
Repair Techniques

Repair by welding is widely used in the shipbuilding industry during ship construction. The effect of the residual stress distribution induced by the welding process on the ship structure is important for the repair effectiveness. This article presents an experimental study of the residual stress distribution induced by repair welding in the plates that are typically used in ships and offshore structures. Different repair techniques are evaluated to identify the best practice associated with residual stress values. Recommendations for repair welding are discussed, and modifications to the present practice are proposed.

Modeling and Prediction of Residual Stresses in Additive Layer Manufacturing by Microplasma Transferred Arc Process Using Finite Element Simulation

2019 ◽  
Vol 141 (6) ◽  
Author(s):  
Sagar H. Nikam ◽  
N. K. Jain
Keyword(s):  
Residual Stress ◽  
Finite Element ◽  
Temperature Distribution ◽  
Residual Stresses ◽  
Substrate Material ◽  
Tensile Residual Stress ◽  
Additive Layer Manufacturing ◽  
Element Simulation ◽  
Layer Manufacturing ◽  
Transferred Arc

Prediction of residual stresses induced by any additive layer manufacturing process greatly helps in preventing thermal cracking and distortion formed in the substrate and deposition material. This paper presents the development of a model for the prediction of residual stresses using three-dimensional finite element simulation (3D-FES) and their experimental validation in a single-track and double-track deposition of Ti-6Al-4V powder on AISI 4130 substrate by the microplasma transferred arc (µ-PTA) powder deposition process. It involved 3D-FES of the temperature distribution and thermal cycles that were validated experimentally using three K-type thermocouples mounted along the deposition direction. Temperature distribution, thermal cycles, and residual stresses are predicted in terms of the µ-PTA process parameters and temperature-dependent properties of substrate and deposition materials. Influence of a number of deposition tracks on the residual stresses is also studied. Results reveal that (i) tensile residual stress is higher at the bonding between the deposition and substrate and attains a minimum value at the midpoint of a deposition track; (ii) maximum tensile residual stress occurs in the substrate material at its interface with deposition track. This primarily causes distortion and thermal cracks; (iii) maximum compressive residual stress occurs approximately at mid-height of the substrate material; and (iv) deposition of a subsequent track relieves tensile residual stress induced by the previously deposited track.

Sign in / Sign up

Export Citation Format

Share Document