Effects of Milling Variables in Amorphous Phase Formation of Fe78Si9B13 Alloy Produced by Mechanical Alloying

2021 ◽  
Vol 876 ◽  
pp. 19-24
Author(s):  
Raquel Astacio López ◽  
Rosa M. Aranda Louvier ◽  
Petr Urban ◽  
Fátima Ternero Fernández ◽  
Juan Manuel Montes Martos
Keyword(s):  
Electron Microscopy ◽  
Mechanical Alloying ◽  
Amorphous Phase ◽  
Milling Time ◽  
Morphological Evolution ◽  
X Ray Diffraction ◽  
Transmission Electron ◽  
Nanocrystalline And Amorphous ◽  
Gas Atmosphere ◽  
Amorphous Phase Formation

In this study, amorphous Fe78Si9B13 alloy was successfully synthesized by mechanical alloying (MA) of pure elemental powders which were milled under an argon gas atmosphere. Effects of milling time on the phase transformation, microstructure and morphological evolution were studied by X-ray diffraction (XRD), laser diffraction (Granulometry), scanning electron microscopy (SEM) and transmission electron microscopy (TEM). Results showed that by increasing the milling time, the nanocrystalline and amorphous phase content increases and alloys with good properties are obtained at 100 h of milling.

Solid State Amorphization of Ti60Si40 Alloy via Mechanical Alloying

2021 ◽  
Vol 876 ◽  
pp. 7-12
Author(s):  
Petr Urban ◽  
Fátima Ternero Fernández ◽  
Rosa M. Aranda Louvier ◽  
Raquel Astacio López ◽  
Jesus Cintas Físico
Keyword(s):  
Electron Microscopy ◽  
Particle Size ◽  
Mechanical Alloying ◽  
Amorphous Phase ◽  
Milling Time ◽  
X Ray Diffraction ◽  
Mechanically Alloyed ◽  
Scanning Calorimetry ◽  
Transmission Electron ◽  
Heating Up

The effect of milling time on the microstructure evolution and formation of amorphous phase of Ti60Si40 alloy produced by mechanical alloying (MA) has been investigated. Laser diffraction, Scanning Electron Microscopy (SEM), X-ray Diffraction (XRD), Transmission Electron Microscopy (TEM) and Differential Scanning Calorimetry (DSC) were employed to characterize the particle size, morphology and structure of mechanically alloyed Ti60Si40. When the milling time is increased to 20 h, the particle size decreases from 23.7 to 4.7 μm, the shape of the particles changes to spherical and the crystalline structure is transformed into an amorphous phase. The amorphous Ti60Si40 alloy is stable when heating up to 750oC. Above this temperature, the cold crystallization of the intermetallic compounds Ti5Si3 and/or Ti5Si4 begins.

Synthesis and Evaluations of Microstructure Properties on Al-(50, 60, 70 mass%)Si Systems by Mechanical Alloying

2004 ◽  
Vol 449-452 ◽  
pp. 249-252 ◽  
Author(s):  
Jung Il Lee ◽  
Tae Whan Hong ◽  
Il Ho Kim ◽  
Soon Chul Ur ◽  
Young Geun Lee ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Mechanical Alloying ◽  
Milling Time ◽  
Alloy System ◽  
Misfit Strain ◽  
X Ray Diffraction ◽  
Mechanically Alloyed ◽  
X Ray ◽  
Transmission Electron ◽  
Nanocrystalline Structures

High silicon Al-Si alloy powders having nanocrystalline structures have been produced by mechanical alloying process. Microstructures in mechanically alloyed Al-Si powders were investigated by scanning electron microscopy and transmission electron microscopy. X-ray diffraction analyses were also carried out to characterize lattice constant, crystallite size and misfit strain. Effective milling time for the formation of nanocrystalline microstructure was thought to be approximately 12 hours, and the sizes of Al and Si crystallites in mechanically alloyed powders after longer than 12 hours of milling were reduced to about 30nm and 70nm respectively, in Al-70 mass% Si alloy system. The misfit strains increased with milling time up to 240 hours, and saturated to 5.73×10-3 and 4.39×10-3 for Al and Si crystallites, respectively.

Fabrication of Amorphous Ti63.7Nb21.3Zr4.5Ta1.5Fe9 Powder by Mechanical Alloying

2013 ◽  
Vol 700 ◽  
pp. 23-26
Author(s):  
Feng Xian Li ◽  
Yi Chun Liu
Keyword(s):  
Electron Microscopy ◽  
Stainless Steel ◽  
Mechanical Alloying ◽  
Pure Titanium ◽  
Amorphous Structure ◽  
X Ray Diffraction ◽  
Transmission Electron ◽  
Gas Atmosphere ◽  
Steel Balls ◽  
Future Work

Amorphous Ti63.7Nb21.3Zr4.5Ta1.5Fe9 powder has been designed and fabricated by mechanical alloying (MA) from a mixture of pure titanium and other elemental powders under a purified argon gas atmosphere in a stainless steel vial together with stainless steel balls. The amorphous alloy powders were examined by X-ray diffraction (XRD), scanning electron microscopy (SEM) and transmission electron microscopy (TEM). The results show that a transform from a well-developed dislocation substructure to a mixed nanocrystalline plus amorphous structure occurs in Ti63.7Nb21.3Zr4.5Ta1.5Fe9 when milling time increases from 0 h to 15 h. Moreover, amorphous Ti63.7Nb21.3Zr4.5Ta1.5Fe9 powders were prepared after mechanical milling for 40 h. The results obtained are of the most significance for future work of densification of the milled powders.

On the Mechanical Milling of the AlCuFe Icosahedral Phase with Water

2014 ◽  
Vol 793 ◽  
pp. 23-27
Author(s):  
C. Patiño-Carachure ◽  
J. Luis López-Miranda ◽  
F. de la Rosa ◽  
M. Abatal ◽  
R. Pérez ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Milling Time ◽  
Induction Furnace ◽  
Icosahedral Phase ◽  
Quasicrystalline Phase ◽  
X Ray Diffraction ◽  
Cast Sample ◽  
X Ray ◽  
Transmission Electron ◽  
Icosahedral Quasicrystalline

In this investigation the Al64Cu24Fe12 alloy was melted in an induction furnace and solidified under normal casting conditions. The as-cast sample was subject to a heat treatment at 700 oC under argon atmosphere in order to obtain the icosahedral quasicrystalline phase in a monophase region. Subsequently, the icosahedral phase was milled for different times and water added conditions. The pre-alloyed and milled powders were characterized using scanning electron microscopy, X-Ray diffraction, and transmission electron microscopy. The experimental results showed that the icosahedral phase is sensitive to the reaction between water and aluminum of the quasicrystalline alloy to generate hydrogen. As the milling time and the amount of water are increased, the embrittlement reaction of the alloy is accentuated releasing more hydrogen.

The Synthesis of Cu0.81Ni0.19 Intermetallics by Mechanical Alloying

2012 ◽  
Vol 496 ◽  
pp. 379-382
Author(s):  
Rui Song Yang ◽  
Ming Tian Li ◽  
Chun Hai Liu ◽  
Xue Jun Cui ◽  
Yong Zhong Jin
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Grain Size ◽  
Mechanical Alloying ◽  
Milling Time ◽  
Elemental Powder ◽  
X Ray Diffraction ◽  
X Ray ◽  
Scherrer Equation ◽  
Scanning Electron

The Cu0.81Ni0.19 has been synthesized directly from elemental powder of nickel and copper by mechanical alloying. The alloyed Cu0.81Ni0.19 alloy powders are prepared by milling of 8h. The grain size calculated by Scherrer equation of the NiCu alloy decreased with the increasing of milling time. The end-product was analyzed by X-ray diffraction (XRD), scanning electron microscopy (SEM)

Effect of Boron on the Amorphization of Fe-Si Alloys by Mechanical Alloying

2012 ◽  
Vol 730-732 ◽  
pp. 739-744 ◽  
Author(s):  
Petr Urban ◽  
Francisco Gomez Cuevas ◽  
Juan M. Montes ◽  
Jesus Cintas
Keyword(s):  
Electron Microscopy ◽  
Mechanical Alloying ◽  
Alloy System ◽  
High Energy ◽  
Milling Process ◽  
X Ray Diffraction ◽  
Scanning Calorimetry ◽  
Structural And Phase Transformations ◽  
Transmission Electron ◽  
Energy Ball

The amorphization process by mechanical alloying in the Fe-Si alloy system has been studied. High energy ball milling has been applied for alloys synthesis. X-ray diffraction (XRD), differential scanning calorimetry (DSC), scanning electron microscopy (SEM) and transmission electron microscopy (TEM) were used to monitor the structural and phase transformations through the different stages of milling. The addition of amorphous boron in the milling process and the increase of the milling time were used to improve the formation of the amorphous phase. Heating the samples resulted in the crystallization of the synthesized amorphous alloys and the appearance of equilibrium intermetallic compounds.

Phase Formation, Stability and Superconducting Properties of Mechanically Alloyed Yttrium-Nickel-Borocarbides

1998 ◽  
Vol 547 ◽  
Author(s):  
L. Ledig ◽  
D. Hough ◽  
C.-G. Oertel ◽  
J. Eckert ◽  
W. Skrotzki
Keyword(s):  
Amorphous Phase ◽  
Amorphous State ◽  
Superconducting Properties ◽  
X Ray Diffraction ◽  
Mechanically Alloyed ◽  
X Ray ◽  
Milling Parameters ◽  
Transmission Electron ◽  
Nanocrystalline And Amorphous ◽  
Nickel Borocarbides

AbstractThe solid state reaction of YNi2B2C by mechanical alloying of elemental powders has been investigated by X-ray diffraction, transmission electron microscopy and susceptibility measurements. Depending on the ball milling parameters either nanocrystalline YNi2B2C or an amorphous phase can be produced. Crystallization of the amorphous phase by annealing at 893 K produces YNi2B2C as major and Ni2B as minor intermetallic compound. Superconductivity is only observed in the annealed state. However, the transition temperature is much lower than in arc-melted samples. This is discussed with respect to the nanocrystalline and amorphous state as well as deviations from stoichiometry produced by impurities introduced during milling.

The Investigation of Structural and Magnetic Properties at High-Temperature of Nanostructured Fe90-Mg10 Alloys Produced by Mechanical Alloying

2018 ◽  
Vol 54 ◽  
pp. 136-145
Author(s):  
A. El Mohri ◽  
M. Zergoug ◽  
K. Taibi ◽  
M. Azzaz
Keyword(s):  
High Temperature ◽  
Mechanical Alloying ◽  
Milling Time ◽  
High Energy ◽  
Lattice Parameter ◽  
X Ray Diffraction ◽  
Transmission Electron ◽  
High Energy Ball Mill ◽  
Energy Ball ◽  
The Mean

Nanocrystalline Fe90Mg10 alloy samples were prepared by mechanical alloying process using planetary high energy ball mill. The prepared powders were characterized using differential thermal analysis (DTA), X-ray diffraction technique (XRD) at high temperature, transmission electron microscopy (TEM), and the vibrating sample magnetometer (VSM). Obtained results are discussed according to milling time. XRD at high temperature results also indicated that when the milling time increases, the lattice parameter and the mean level of grain size increase, whereas the microstrains decrease. The result of the observation by the TEM of the Fe-Mg powders prepared in different milling time, coercive fields derived and Saturation magnetization derived from the hysteresis curves in high temperature are discussed as a function of milling time.

Micro/nanostructure observation of microwave-heated Fe3O4

2009 ◽  
Vol 24 (5) ◽  
pp. 1741-1747 ◽  
Author(s):  
Noboru Yoshikawa ◽  
Ziping Cao ◽  
Dmitri Louzguin ◽  
Guoqiang Xie ◽  
Shoji Taniguchi
Keyword(s):  
Amorphous Phase ◽  
Single Mode ◽  
Lattice Parameter ◽  
State University ◽  
X Ray Diffraction ◽  
Transmission Electron ◽  
Penn State ◽  
Local Transport ◽  
O Phase ◽  
Amorphous Phase Formation

To investigate the microwave (MW) processing of Fe3O4, for which occurrence of decrystallization has been reported, the micro/nanostructures of MW-heated Fe3O4 powder were observed in this study. The specimens were irradiated by 2.45 GHz MW at the position of magnetic (H)-field maximum in a TE10 single mode applicator. The specimen was heated well above the Curie temperature in H-field. The heated specimen above 1000 °C revealed the glass-like surface with the diminished x-ray diffraction (XRD) peak intensities. They resemble the reported features of decrystallization in an earlier work performed at Penn State University. According to the XRD profiles of the MW-heated specimens, formation of FeO and shift of Fe3O4 peaks to the lower angle with the broadened width were observed. To account for the findings, a model is presented that phase separation occurred into FeO and Fe3O4 resulting in an increased lattice parameter due to the increased oxygen content. This activity is caused by local transport of oxygen in nanoscale. Considering the shape of the main XRD Fe3O4 peak with a shoulder and the existence of halo in nanobeam diffraction (NBD), amorphous phase areas exist. As a result of transmission electron microscopy observation, it was shown that they were in nanoscaled localized regions, and it was not confirmed that the glass-like morphologies (or decrystallized morphologies) are totally amorphous. The observed micro/nanostructures and mechanism of the amorphous phase formation were discussed considering the Fe-O phase diagram.

Sign in / Sign up

Export Citation Format

Share Document