The Synthesis of Cu0.81Ni0.19 Intermetallics by Mechanical Alloying

2012 ◽  
Vol 496 ◽  
pp. 379-382
Author(s):  
Rui Song Yang ◽  
Ming Tian Li ◽  
Chun Hai Liu ◽  
Xue Jun Cui ◽  
Yong Zhong Jin
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Grain Size ◽  
Mechanical Alloying ◽  
Milling Time ◽  
Elemental Powder ◽  
X Ray Diffraction ◽  
X Ray ◽  
Scherrer Equation ◽  
Scanning Electron

The Cu0.81Ni0.19 has been synthesized directly from elemental powder of nickel and copper by mechanical alloying. The alloyed Cu0.81Ni0.19 alloy powders are prepared by milling of 8h. The grain size calculated by Scherrer equation of the NiCu alloy decreased with the increasing of milling time. The end-product was analyzed by X-ray diffraction (XRD), scanning electron microscopy (SEM)

Structural Evolution of the Cu-Ni Solid Solution Formed by Ball Mechanical Alloying Treatment (BMAT)

2011 ◽  
Vol 673 ◽  
pp. 279-284 ◽  
Author(s):  
Iman Farahbakhsh ◽  
Alireza Zakeri ◽  
Palavesamuthu Manikandan ◽  
Kazuyuki Hokamoto
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Mechanical Alloying ◽  
Milling Time ◽  
Structural Evolution ◽  
Mutual Diffusion ◽  
X Ray Diffraction ◽  
X Ray ◽  
Ma Process ◽  
Scanning Electron

A nanostructured powder with uniform distribution of Ni and Cu powders was produced by means of the Ball Mechanical Alloying Treatment (BMAT). Mutual diffusion of Ni and Cu in the nanostructured layer and the microstructure of the cross section of the remaining powders were investigated by X-ray diffraction (XRD), scanning electron microscopy (SEM) and Electron Probe Microanalyzer (EPMA). X-ray diffraction patterns revealed that increasing the milling time gives rise to decreasing crystallite size and lattice parameter during the MA process. Furthermore, scanning electron microscopy (SEM) was utilized not only for evaluating the morphology and microstructure of the remaining powder particles but also for proving this claim that during MA process, the mutual diffusion of Ni and Cu has occurred. Elemental mappings also show that the alloying process occurred in samples but obtaining the uniform shape, size and microstructure of the powder requires increase in the milling time.

Dissolution of Al 6%wt c Mixture Using Mechanical Alloying

2019 ◽  
Vol 391 ◽  
pp. 82-87
Author(s):  
R. Dabouz ◽  
Meriem Bendoumia ◽  
Lounes Belaid ◽  
Mohamed Azzaz
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Mechanical Alloying ◽  
Solid Solubility ◽  
Milling Time ◽  
X Ray Diffraction ◽  
Processing Methods ◽  
X Ray ◽  
Scanning Electron

In the equilibrium processing methods the system Al-C does not show any solid solubility which means that carbon is not soluble in aluminum. In this work an investigation of mechanical alloying on system Al-C was presented to force the dissolution. Using different techniques such as the X-ray diffraction and scanning electron microscopy (SEM), it was proved the force of dissolution by studying the specters for different milling time and by flowing the evolution during annealing into a DSC. Furthermore, morphology of phases has been studied.

Light Burning Condition of Preparing Dolomite Clinker Using Natural Dolomite

2018 ◽  
Vol 281 ◽  
pp. 156-162
Author(s):  
Wang Nian Zhang ◽  
Xi Tang Wang ◽  
Zhou Fu Wang
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Grain Size ◽  
Sintering Process ◽  
X Ray Diffraction ◽  
Burning Temperature ◽  
X Ray ◽  
Temperature Range ◽  
Scanning Electron

The influence of the light burning temperature on the sintering property of nature dolomite has been investigated by two-step sintering process in the temperature range 1500 °C to 1600 °C. The resulting bulk densities and apparent porosities of the sintered dolomite samples were examined, and analyzing the sintered dolomite by scanning electron microscopy and X-ray diffraction were performed. The results showed light burned at 850 °C for 3 h, the main phases of the dolomite with 3-5 grain size were MgO, CaO and little CaCO3, and then fired at 1600 °C,the density of sintering dolomite reached to 3.38 g/cm3, the apparent property was 1.2 %, the size of MgO grain up to 3.75 μm . However when dolomite light burned at 1050 °C for 3 h, the main phases were MgO and CaO, and then fired at 1600 °C,the density of sintering dolomite only was 3.30 g/cm3, the apparent property was 2.3 %, the size of MgO only was 3.05 μm .

The Effects of Al-Ca Compounds on Grain Refinement of Mg-Ca Alloys

2011 ◽  
Vol 686 ◽  
pp. 348-354 ◽  
Author(s):  
Shu Tao Xiong ◽  
Fu Sheng Pan ◽  
Bin Jiang ◽  
Xiao Ke Li
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Grain Size ◽  
Grain Refinement ◽  
X Ray Diffraction ◽  
X Ray ◽  
Metallic Compound ◽  
Scanning Electron ◽  
Main Factor

In the present work, Al-Ca metallic compound was prepared in Mg-Ca alloys and the effects of Al-Ca metallic compound and different Al/Ca values on the grain refinement of Mg-Ca alloys were investigated by scanning electron microscopy and X-ray diffraction, and the mechanism of grain refinement of Mg-Ca alloys was discussed. The results showed that the grain size of Mg-0.5Ca alloy was obviously reduced from 550μm to 230μm due to the addition of Al. Al2Ca phase existed in these alloys and its morphology evolved from granular to rod-like. It is regarded as the main factor for the grain refinement.

Grain Size Effect on Lattice of Ni Nanocrystals Prepared Through Polyol Method

2008 ◽  
Vol 8 (8) ◽  
pp. 4127-4131 ◽  
Author(s):  
G. S. Okram ◽  
Kh. Namrata Devi ◽  
H. Sanatombi ◽  
Ajay Soni ◽  
V. Ganesan ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Atomic Force Microscopy ◽  
Grain Size ◽  
Polyol Method ◽  
X Ray Diffraction ◽  
X Ray ◽  
Force Microscopy ◽  
Atomic Force ◽  
Scanning Electron

Nanocrystalline nickel powders were prepared with grain size 'd' in the range 40–100 nm diameters through polyol method. X-ray diffraction (XRD), scanning electron microscopy (SEM) and atomic force microscopy (AFM) were used for characterization. XRD of the prepared samples consistently matched with standard fcc structure of nickel without any impurity peak. Detailed analysis and calculations using Scherrer equation for (111) peak revealed systematic increase in line width and peak shifting towards lower diffraction 2θ angles with decrease in nickel to ethylene glycol mole ratio. Different values of d estimated from various peaks of each sample suggested associated microstrains in the nanograins. Values of d estimated from X-ray diffraction patterns were compared with those obtained from atomic force microscopy and scanning electron microscopy results, and discussed. Observed lattice expansion is explained, on the basis of a theoretical model of linear elasticity.

Effect of Ti and Sb Elements Addition on the Microstructure and Corrosion Resistance of Hot-Dip Galvanized Zn-11Al-3Mg Alloy

2021 ◽  
Vol 1035 ◽  
pp. 630-637
Author(s):  
Hui Jie Sun ◽  
Guo Rong Zhou ◽  
Ming Ming Zhang ◽  
Xue Feng Wang ◽  
Shui Yu ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Grain Size ◽  
Corrosion Resistance ◽  
Energy Dispersive Spectrometry ◽  
X Ray Diffraction ◽  
Rich Phase ◽  
X Ray ◽  
Pitting Corrosion Resistance ◽  
Scanning Electron

The effect of Ti and Sb elements addition on the microstructures and corrosion resistance of hot-dip galvanized Zn-11Al-3Mg alloy was investigated by scanning electron microscopy (SEM) equipped with energy dispersive spectrometry (EDS), X-ray diffraction (XRD) and Electrochemical workstation, respectively. Results showed that the grain size of the alloy was obviously refined with the addition of Ti and Sb elements, due to Al3Ti phase as the nucleation substrate resulted in the transformation of Al-rich phase from dendrite to petal-like. In addition, the pitting corrosion resistance of the alloy has been significantly enhanced.

Phase transformations and microstructural evolution in nanocrystalline Fe71B23Nb6 alloy prepared by mechanical alloying

2020 ◽  
Vol 111 (4) ◽  
pp. 307-315
Author(s):  
Mahmoud Chemingui ◽  
Chahida Mnasri ◽  
Christelle Nivot ◽  
Arnaud Tricoteaux ◽  
Yannick Lorgouilloux ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Mechanical Alloying ◽  
Alloy Powder ◽  
Milling Time ◽  
Milling Process ◽  
Microstructural Properties ◽  
X Ray Diffraction ◽  
X Ray ◽  
Prepared Alloy ◽  
Scanning Electron

Abstract A new nanocrystalline Fe71B23Nb6 alloy powder was prepared by mechanical alloying. The phase transformation and morphological and microstructural properties of the as-prepared alloy were investigated by scanning electron microscopy, laser granulometry, and X-ray diffraction with respect to the milling time (0- 200 h). During the milling process, it was observed that the dissolution of Nb and B atoms into the Fe matrix formed solid solutions of Fe (Nb), Fe (B), Fe23B6, Fe2B, and Fe (Nb, B). Moreover, the insertion of B atoms into the Nb network generated the Nb (B) phase. Furthermore, the minimum crystallite size was measured as approximately 1 nanometer. In addition, the dislocation density gradually increased with the extension of the milling time, and the crystallization of the partially amorphous phase occurred after 200 h of milling.

scholarly journals Infiltration Behavior Of Mechanical Alloyed 75 wt% Cu-25 wt% WC Powders Into Porous WC Compacts

2015 ◽  
Vol 60 (2) ◽  
pp. 1565-1568
Author(s):  
A. Şelte ◽  
B. Özkal
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Mechanical Alloying ◽  
High Energy ◽  
X Ray Diffraction ◽  
X Ray ◽  
Microstructural Evaluation ◽  
Infiltration Behavior ◽  
Infiltration Method ◽  
Scanning Electron

AbstractIn this work infiltration behavior of mechanical alloyed 75 wt% Cu – 25 wt% WC powders into porous WC compacts were studied. Owing to their ductile nature, initial Cu powders were directly added to mechanical alloying batch. On the other hand initial WC powders were high energy milled prior to mechanical alloying. Contact infiltration method was selected for densification and compacts prepared from processed powders were infiltrated into porous WC bodies. After infiltration, samples were characterized via X-Ray diffraction studies and microstructural evaluation of the samples was carried out via scanning electron microscopy observations. Based on the lack of solubility between WC and Cu it was possible to keep fine WC particles in Cu melt since solution reprecipitation controlled densification is hindered. Also microstructural characterizations via scanning electron microscopy confirmed that the transport of fine WC fraction from infiltrant to porous WC skeleton can be carried out via Cu melt flow during infiltration.

scholarly journals Structural properties of the composites (BaFe12O19/Ni0.3Cu0.2Zn0.5Al-0.5Fe1.5O4) prepared by sol-gel auto combustion

2019 ◽  
Vol 24 (4) ◽  
pp. 69
Author(s):  
Mohammed Mustafa Rashid1 ◽  
Sabah J. Fathi2 ◽  
Rafea A. Munef ◽  
Bilal Omer Ahmed1
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Grain Size ◽  
Sol Gel ◽  
Structural Features ◽  
Nano Composites ◽  
X Ray Diffraction ◽  
X Ray ◽  
Auto Combustion ◽  
Scanning Electron

The nanocomposites ferrites (BaFe12O19/Ni0.3Cu0.2Zn0.5Al­0.5Fe1.5O4) with (x=10,25,50,75,90%) were prepared by sol-gel auto combustion. The micro-structural features of the samples were studied using X-ray diffraction (XRD) and scanning electron microscopy (SEM) techniques. The results were compared which show that the grain size of the nano composites which prepared by sol-gel auto combustion about (25-46) nm.   http://dx.doi.org/10.25130/tjps.24.2019.075  

Sign in / Sign up

Export Citation Format

Share Document