Tensile Properties of MoSi2 at Elevated Temperatures

2004 ◽  
Vol 449-452 ◽  
pp. 845-848 ◽  
Author(s):  
Ai Dang Shan ◽  
Jian Sheng Wu ◽  
Hitoshi Hashimoto ◽  
Yong Ho Park
Keyword(s):  
Activation Energy ◽  
Grain Size ◽  
Strain Rate ◽  
Tensile Properties ◽  
Elevated Temperatures ◽  
Strain Rate Range ◽  
Rate Range ◽  
Energy Value ◽  
Lower Strain ◽  
Ductility Maximum

The tensile properties of two MoSi2 alloys with different grain sizes (1 micrometer and 10 micrometer) were evaluated in vacuum at temperatures ranging from 1400 to 1600K and initial strain rates ranging from 1×10-5/s to 1×10-3/s. For the alloy with 10micron grain size an m vale of 0.35 and an activation energy value of 350 kJ/mol were observed in the lower strain rate range while an m value of 0.12 and an activation energy value of 760 kJ/mol were observed in the higher strain rate range. For the alloy with 1micron grain size, a uniform m value of 0.55 and an activation energy value of 160 kJ/mol were observed. Moreover these two alloys showed remarkable ductility (maximum 33%) in the test temperatures. The deformation mechanism and the remarkable ductility are discussed in the light of the microstructural observations through SEM and TEM.

scholarly journals Study on Plastic Deformation Behavior of Mo-10Ta under Ultra-High Strain Rate

Metals ◽  
2020 ◽  
Vol 10 (9) ◽  
pp. 1153
Author(s):  
Ping Song ◽  
Wen-Bin Li ◽  
Yu Zheng ◽  
Jiu-Peng Song ◽  
Xiang-Cao Jiang ◽  
...  
Keyword(s):  
Activation Energy ◽  
High Strain Rate ◽  
Strain Rate ◽  
Strain Rate Sensitivity ◽  
Deformation Behavior ◽  
High Strain ◽  
Rate Sensitivity ◽  
Strain Rate Range ◽  
Rate Range ◽  
Strain Relationship

This study investigated the deformation behavior of the Mo-10Ta alloy with a strain rate range of 102–105 s−1. The Split Hopkinson pressure bar (SHPB) experiments were conducted to investigate the influence of deformation conditions on the stress-strain relationship and strain rate sensitivity of the material within a strain rate range of 0.001–4500 s−1. The Shaped Charge Jet (SCJ) forming experiments under detonation loading was conducted to clarify the dynamic response and microstructure evolution of the material within an ultra-high strain rates range of 104–105 s−1. Based on the stress-strain relationship of Mo-10Ta alloy at high temperature (286–873 K) and high strain rate (460–4500 s−1), the influence of temperature and strain rate on the activation energy Q was analyzed. The results indicate that the material strain rate sensitivity increased with the increase in strain rate and strain. Meanwhile, the activation energy Q decreased as the temperature and strain rate increased. The plasticity of the Mo-10Ta alloy under the condition of SCJ forming was substantially enhanced compared with that under quasi-static deformation. The material grain was also refined under ultra-high strain rate, as reflected by the reduction in grain size from 232 μm to less than 10 μm.

Compressive strength of iceberg ice

2003 ◽  
Vol 81 (1-2) ◽  
pp. 191-200 ◽  
Author(s):  
S J Jones ◽  
R E Gagnon ◽  
A Derradji ◽  
A Bugden
Keyword(s):  
Grain Size ◽  
Compressive Strength ◽  
Strain Rate ◽  
Strain Rate Range ◽  
Air Bubbles ◽  
Strain Rates ◽  
Thin Sections ◽  
Rate Range ◽  
A Value ◽  
Wide Range

The uniaxial compressive strength of iceberg ice was determined over a wide range of strain rates from 10–8 to 10+1 s–1 at –10°C. It was found that for strain rates less than 10–4 s–1, strength increased in a power-law manner with strain rate. Above 10–4 s–1, the strength was essentially constant at 4 MPa, dropping slightly between 10–3 and 10–1 s–1, before rising again to a value of about 10 MPa at 10+1 s–1. Thin sections of the ice revealed a small grain size of about 3.5 mm and elongated air bubbles with a ratio of length to width of about 10. In the practical strain-rate range of interest, the maximum failure stress observed was 4.8 MPa. PACS No.: 62.20

A Study at the Workability of Ultra-High Strength Steel Sheet by Processing Maps on the Basis of DMM

2017 ◽  
Vol 36 (7) ◽  
pp. 657-667 ◽  
Author(s):  
Yu Feng Xia ◽  
Shuai Long ◽  
Tian-Yu Wang ◽  
Jia Zhao
Keyword(s):  
Activation Energy ◽  
Strain Rate ◽  
High Strength Steel ◽  
High Strength ◽  
Strain Rate Range ◽  
Diffusion Activation Energy ◽  
Processing Maps ◽  
Rate Range ◽  
Temperature Range ◽  
Ultra High Strength Steel

AbstractThe hot workability of the ultra-high strength steel BR1500HS has been investigated by processing maps. A series of hot deformation tensile tests were carried out on a Gleeble-3500 thermal simulator in the deformation temperature range of 773–1,223 K and strain rate range of 0.01–10 s–1. The obtained flow stress curves reveal that the peak stress increases with the rising of strain rate and decreases with the rising of temperature. Based on dynamic materials model (DMM), the processing maps at the strains of 0.05, 0.10 and 0.15 were developed, and the optimum hot working conditions were recommended as the temperature range of 1,200–1,223 K and the strain rate range of 0.01–0.1 s–1, where the peak power dissipation efficiency is about 37 % revealing the occurrence of typical dynamic recrystallization (DRX). The main instability defects are deformation twinning and micro-crack occurring mainly at the temperature range of 773–873 K with the strain rate higher than 1 s–1. In order to deeply understand the microstructure mechanisms, the Zener–Hollomon parameter is solved, and then the self-diffusion activation energy is compared with the apparent activation energy Q at different deformation temperatures and strain rates.

The Effect of Slow-Constant Strain Rates on the Tensile Properties of Selected Alloys at Room and Elevated Temperatures

1974 ◽  
Vol 96 (2) ◽  
pp. 115-122 ◽  
Author(s):  
C. L. Dotson
Keyword(s):  
Strain Rate ◽  
Elevated Temperatures ◽  
Tensile Tests ◽  
Strength Properties ◽  
Strain Rate Range ◽  
Dynamic Strain ◽  
Strain Rates ◽  
Lower Strain ◽  
Temperature Ranges ◽  
Design Stress

Tensile tests were performed at constant strain rates from 10−2 to 10−5 min−1 on 5454-O and 1100-O aluminum alloys, A515 Grade 70 steel and B166 nickel alloy at room temperature and at elevated-temperature ranges where the design stress basis normally changes from tensile to creep-rupture controlled. The results in general showed that the strength of the alloys decreased at lower strain rates, and the sensitivity to strain rate was greater at elevated temperatures except where metallurgical phenomena such as dynamic strain aging negate the effects of strain rate. At the highest temperature the decrease in strength properties ranged from 11 to 50 percent over the strain rate range for different alloys.

High Strain Rate Deformation Behavior of Mg–Al–Zn Alloys at Elevated Temperatures

2007 ◽  
Vol 340-341 ◽  
pp. 107-112 ◽  
Author(s):  
Hiroyuki Watanabe ◽  
Koichi Ishikawa ◽  
Toshiji Mukai
Keyword(s):  
High Temperature ◽  
High Strain Rate ◽  
Strain Rate ◽  
Deformation Behavior ◽  
Elevated Temperatures ◽  
High Strain ◽  
Strain Rate Range ◽  
High Temperature Deformation ◽  
Temperature Deformation ◽  
Rate Range

High temperature deformation behavior of AZ31 and AZ91 magnesium alloys was examined by compression tests over a wide strain rate range from 10–3 to 103 s–1 with emphasis on the behavior at high strain rates. The dominant deformation mechanism in the low strain rate range below 10–1 s–1 was suggested to be climb-controlled dislocation creep. On the other hand, experimental results indicated that the deformation at a high strain rate of ~103 s–1 proceeds by conventional plastic flow of dislocation glide and twinning even at elevated temperatures. The solid-solution strengthening was operative for high temperature deformation at ~103 s–1.

DYNAMIC TENSILE AND COMPRESSIVE STRESS-STRAIN CHARACTERISTICS OF MAGNESIUM ALLOYS AT ELEVATED TEMPERATURES

2008 ◽  
Vol 22 (09n11) ◽  
pp. 1135-1140 ◽  
Author(s):  
TEPPEI ARAMOTO ◽  
HIROSHI TACHIYA ◽  
AKIYOSHI HORI ◽  
AKIHIRO HOJO ◽  
YUSUKE MIYAZAKI
Keyword(s):  
Strain Rate ◽  
Magnesium Alloys ◽  
Dynamic Stress ◽  
Elevated Temperatures ◽  
Compressive Load ◽  
Tensile Load ◽  
Strain Rate Range ◽  
Stress Strain ◽  
Rate Range ◽  
Temperature Ranges

The dynamic stress-strain characteristics of magnesium alloys have not been clarified sufficiently. Thus, the study investigated both the compressive and tensile dynamic stress-strain characteristics of representative magnesium alloys: AZ61A-F, ZK60A-T5 and AZ31B-F at wide strain rate and temperature ranges. About the strain rate dependency, the dynamic stresses are higher than the static ones under both compressive and tensile loads at elevated temperatures; however the dynamic stress-strain relations change slightly in the dynamic strain rate range. Thus, the magnesium alloys has little strain rate dependence. However, the elongation of the dynamic stress-strain relations under tensile load tends to be larger than that of static one. About the temperature dependency, the yield and flow stresses of the investigated magnesium alloys under compressive load decrease abruptly at temperatures higher than about 600 K in the wide strain rate range. Meanwhile, the ones under tensile load decrease with the temperature more gently. Totally, the magnesium alloys exhibit low temperature dependence. Furthermore, as well known, the yield stresses caused under the tensile load exhibit about twice as high as those under compressive load. This study verified that such a characteristic can be observed over a wide strain rate and temperature ranges.

scholarly journals Dynamic Mechanical Behavior and Microstructure Evolution of an Extruded 6013-T4 Alloy at Elevated Temperatures

Metals ◽  
2019 ◽  
Vol 9 (6) ◽  
pp. 629 ◽  
Author(s):  
Tuo Ye ◽  
Yuanzhi Wu ◽  
Wei Liu ◽  
Bin Deng ◽  
Anmin Liu ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Strain Rate ◽  
Stress Level ◽  
Microstructure Evolution ◽  
Elevated Temperatures ◽  
Strain Rate Range ◽  
Rate Range ◽  
Dynamic Mechanical Behavior ◽  
Strain And Strain Rate ◽  
Increasing Temperature

The mechanical properties of an extruded 6013-T4 alloy were tested at a temperature range from 25 to 400 °C and strain rate range from 1 × 103 to 5 × 103 s−1. The results demonstrate that the stress level is sensitive to strain rate and temperature. The stress level increases slightly with increasing strain rate and decreases remarkably with increasing temperature. The dislocation and precipitate undergo great changes. When deformed at 25 °C, the density of the dislocation increases with strain and strain rate; which leads to a higher stress level. A great number of needle-like precipitates were observed at samples deformed at 200 °C. It is clear that the density of dislocation increases with strain and strain rate. When impacted at 400 °C, the coarser precipitates were found in the specimen; the density of the dislocation increases with strain and strain rate.

Sign in / Sign up

Export Citation Format

Share Document