Continuous Dynamic Recrystallization of AISI 430 Ferritic Stainless Steel by Hot Torsion Deformation

2005 ◽  
Vol 475-479 ◽  
pp. 145-148 ◽  
Author(s):  
Jae-Young An ◽  
Suk Min Han ◽  
Young Jae Kwon ◽  
Yeon Chul Yoo
Keyword(s):  
Stainless Steel ◽  
Flow Stress ◽  
Dynamic Recrystallization ◽  
Ferritic Stainless Steel ◽  
High Temperature Deformation ◽  
Temperature Deformation ◽  
High Angle ◽  
Continuous Dynamic Recrystallization ◽  
Continuous Dynamic ◽  
Aisi 430

The high temperature deformation behavior of AISI 430 ferritic stainless steel has been studied over a temperature range of 800 to 1000°C and strain rate of 0.05-5.0/sec. The evolution of flow stress and microstructures showed the characteristics of continuous dynamic recrystallization (CDRX). The flow stress curves gradually decreased with increasing strain over the peak stress until 500% of strain without any steady state shown in typical austenitic stainless steel. Sub-grains of low angle firstly formed along the original high angle grain boundary were propagated into the inside of original grain and transformed to high angle. The CDRX grain sizes of AISI 430 deformed at 1000 °C and 0.5/sec was about 30-35㎛.

scholarly journals A Combined Method to Model Dynamic Recrystallization Based on Cellular Automaton and a Phenomenological (CAP) Approach

Metals ◽  
2018 ◽  
Vol 8 (11) ◽  
pp. 923 ◽  
Author(s):  
Morteza Azarbarmas ◽  
Seyed Mirjavadi ◽  
Ali Ghasemi ◽  
Abdel Hamouda
Keyword(s):  
Dynamic Recrystallization ◽  
Cellular Automaton ◽  
Present Model ◽  
Phenomenological Approach ◽  
High Temperature Deformation ◽  
Temperature Deformation ◽  
Flow Curves ◽  
Continuous Dynamic Recrystallization ◽  
Proposed Model ◽  
Continuous Dynamic

Titanium alloys with high stacking-fault energy show continuous dynamic recrystallization (CDRX) instead of discontinuous dynamic recrystallization (DDRX) during high-temperature deformation. During the CDRX mechanism, new recrystallized grains are generated by the progressive increasing of the low-angle boundary misorientations. In the present work, the CDRX phenomenon was modeled by using a cellular automaton (CA)-based method. The size of seeds was determined based on a phenomenological approach, and then the number and distribution of recrystallized grains as well as the topological changes were applied by utilizing the CA approach. In order to verify the capacity of the proposed model for predicting the microstructural characteristics, the experimental data of the hot-compressed TiNiFe alloy were used. Results showed that the presented model can accurately estimate the fraction of the recrystallized area. Moreover, the macroscopic flow curves of the alloy were well predicted by the present model.

Hot Compression Deformation Behavior of Mg-Gd-Y-Zn-Zr Alloy

2014 ◽  
Vol 680 ◽  
pp. 15-22 ◽  
Author(s):  
Guang Lu ◽  
Zhi Ping Xie ◽  
Zhi Min Zhang ◽  
Yong Biao Yang ◽  
Bao Cheng Li
Keyword(s):  
Flow Stress ◽  
Magnesium Alloy ◽  
Dynamic Recrystallization ◽  
Strain Rate ◽  
Great Influence ◽  
Peak Stress ◽  
Maximum Error ◽  
Continuous Dynamic Recrystallization ◽  
Stress Behaviors ◽  
Continuous Dynamic

The deformation behaviors of as-cast Mg-11Gd-2Y-Zn-Zr magnesium alloy were investigated by compression test with Gleeble-1500 thermal simulator at temperature of 623-753K and strain rate of 0.01-0.5 s-1. The flow stress behaviors of the magnesium alloy were carried out at a strain of 0.7. The strain rate and deformation temperature had great influence on the flow stress behaviors. The flow stress increases with increasing strain rate and decreasing temperature. The flow stress has more than one peak stress at a strain rate of 0.5s-1showing continuous dynamic recrystallization (DRX) mechanism, while other flow stresses exhibited only one peak stress indicating discontinuous dynamic recrystallization (DDRX) mechanism. It was also found that the flow stress behavior could be described by the hyperbolic sine constitutive equation, in which the determined average activation energy is 273.426 kJ·mol-1. The maximum error value between calculated value and experimental value is 5.5%. The deformation map was also established, and the best parameter for hot working was found to be 0.1s-1/753k approximately.

The Role of Deformation Banding in Grain Refinement under ECAP

2014 ◽  
Vol 783-786 ◽  
pp. 2641-2646 ◽  
Author(s):  
Rustam Kaibyshev ◽  
Sergey Malopheyev ◽  
Vladislav Kulitskiy ◽  
Marat Gazizov
Keyword(s):  
Dynamic Recrystallization ◽  
Grain Refinement ◽  
Lamellar Structure ◽  
True Strain ◽  
High Angle ◽  
Continuous Dynamic Recrystallization ◽  
Angular Pressing ◽  
Deformation Banding ◽  
Continuous Dynamic

The mechanism of grain refinement in an Al-5.4Mg-0.4Mn-0.2Sc-0.09Zr alloy subjected to equal-channel angular pressing (ECAP) at 300°C through route BC is considered. It was shown that the formation of geometrically necessary boundaries (GNB) aligned with a {111} plane at ε≤1 initiates the occurrence of continuous dynamic recrystallization (CDRX). Upon further strain the GNBs transform to low-to-moderate angle planar boundaries that produces lamellar structure. In the strain interval 2-4, 3D arrays of planar boundaries evolve due to inducing the formation of 2nd order and higher orders families of GNBs in new {111} planes. GNBs gradually convert to high-angle boundaries (HAB) with strain. A uniform recrystallized structure is produced at a true strain of ∼8. The role of slip concentration and shearing patterns in the formation of GNBs is discussed.

scholarly journals Deformation Behavior and Dynamic Recrystallization of Mg-1Li-1Al Alloy

Metals ◽  
2021 ◽  
Vol 11 (11) ◽  
pp. 1696
Author(s):  
Xiaoyan Feng ◽  
Xue Pang ◽  
Xu He ◽  
Ruihong Li ◽  
Zili Jin ◽  
...  
Keyword(s):  
Flow Stress ◽  
Dynamic Recrystallization ◽  
Strain Rate ◽  
Volume Fraction ◽  
High Temperature Deformation ◽  
Temperature Deformation ◽  
Avrami Equation ◽  
Uniaxial Compression Test ◽  
Hot Workability ◽  
The Relationship

In this paper, the hot workability of Mg-1Li-1Al (LA11) alloy is assessed through a uniaxial compression test in a temperature range from 200 to 400 °C and a strain rate, έ, of 1–0.01 s−1. The present study reveals that flow stress increases when the strain rate increases and deformation temperature decreases. Based on the hyperbolic sine equation, the flow stress constitutive equation of this alloy under high-temperature deformation is established. The average activation energy was 116.5 kJ/mol. Avrami equation was employed to investigate the dynamic recrystallization (DRX). The DRX mechanism affected by the deformation conditions and Zener–Hollomon parameters is revealed. Finally, the relationship between DRX volume fraction and deformation parameter is verified based on microstructure evolution, which is consistent with the theoretical prediction.

scholarly journals Strain Compensation Constitutive Model and Parameter Optimization for Nb-Contained 316LN

Metals ◽  
2019 ◽  
Vol 9 (2) ◽  
pp. 212 ◽  
Author(s):  
Jingdan Li ◽  
Jiansheng Liu
Keyword(s):  
Flow Stress ◽  
Constitutive Model ◽  
Dynamic Recrystallization ◽  
Strain Rate ◽  
Compression Tests ◽  
Continuous Dynamic Recrystallization ◽  
Transmission Electron ◽  
Strain Compensation ◽  
Temperature Ranges ◽  
Continuous Dynamic

Hot deformation behavior of Nb-contained 316LN was investigated using a series of compression tests performed on a Gleeble-1500D simulator at temperature of 950–1200 °C and strain rate of 0.01~1 s−1. Based on the strain compensation method, a modified Arrhenius constitutive model considering the comprehensive effects of temperature, strain rate, and strain on flow stress was established, and the accuracy of the proposed model was evaluated by introducing correlation coefficient (R) and average relative error (AARE). The values of R and AARE were calculated as 0.995 and 4.48%, respectively, proving that the modified model has a high accuracy in predicting the flow stress of Nb-contained 316LN. The microstructure evolution and the dynamic recrystallization (DRX) mechanism of the experimental material were explicated by optical microscopy (OM), electron back scattered diffraction (EBSD), and transmission electron microscopy (TEM). It was found that continuous dynamic recrystallization (CDRX) characterized by subgrain evolution and discontinuous dynamic recrystallization (DDRX) featured by grain boundary nuclei are two main dynamic recrystallization (DRX) mechanisms of Nb-contained 316LN. Furthermore, based on the results of microstructure analyses, optimum parameters were obtained as temperature ranges of 1100~1200 °C and strain rate ranges of 0.01~1 s−1.

Regularities of Grain Refinement in an Austenitic Stainless Steel during Multiple Warm Working

2013 ◽  
Vol 753 ◽  
pp. 411-416 ◽  
Author(s):  
Andrey Belyakov ◽  
Marina Tikhonova ◽  
Zhanna Yanushkevich ◽  
Rustam Kaibyshev
Keyword(s):  
Stainless Steel ◽  
Austenitic Stainless Steel ◽  
Dynamic Recrystallization ◽  
Strain Rate ◽  
Structural Changes ◽  
Continuous Dynamic Recrystallization ◽  
Warm Working ◽  
Fine Grain ◽  
Power Law Function ◽  
Continuous Dynamic

The structural changes that are related to the new fine grain development in a chromium-nickel austenitic stainless steel subjected to warm working by means of multiple forging and multiple rolling were studied. The multiple warm working to a total strain of 2 at temperatures of 500-900C resulted in the development of submicrocrystalline structures with mean grain sizes of 300-850 nm, depending on processing conditions. The new fine grains resulted mainly from a kind of continuous reactions, which can be referred to as continuous dynamic recrystallization. Namely, the new grains resulted from a progressive evolution of strain-induced grain boundaries, the number and misorientation of which gradually increased during deformation. In contrast to hot working accompanied by discontinuous dynamic recrystallization, when the dynamic grain size can be expressed by a power law function of temperature compensated strain rate as D ~ Z-0.4, much weaker temperature/strain rate dependence of D ~ Z-0.1was obtained for the warm working.

Investigation on Dynamic Recrystallization Behavior in Hot Deformed Superalloy Inconel 718

2007 ◽  
Vol 546-549 ◽  
pp. 1297-1300 ◽  
Author(s):  
Y. Wang ◽  
Wen Zhu Shao ◽  
Liang Zhen ◽  
L. Lin ◽  
Y.X. Cui
Keyword(s):  
Dynamic Recrystallization ◽  
Inconel 718 ◽  
High Angle ◽  
Twin Boundaries ◽  
Continuous Dynamic Recrystallization ◽  
Subgrain Rotation ◽  
Dynamic Recrystallization Behavior ◽  
Ebsd Technique ◽  
Continuous Dynamic ◽  
The Individual

The nucleation and development of dynamic recrystallization (DRX) in hot deformed superalloy Inconel 718 during uniaxial compression were investigated by optical microscopy and electron back-scattered diffraction (EBSD) technique. The results showed that the discontinuous dynamic recrystallization was the predominant DRX mechanism in this alloy. The variations of partial crystallographic orientations led to the individual nucleation inside the deformed grains, which implied the occurrence of local continuous dynamic recrystallization. The progressive subgrain rotation can be confirmed neither near the prior high angle grain boundaries nor within the original grains. It was found that, as the strain increased, the initial twin boundaries were gradually transformed to ordinary mobile high angle boundaries. Meanwhile, the new twin boundaries were formed inside the recrystallized grain necklaces. It was suggested that the characteristics of the twin boundaries evolution with increasing strain were associated with the transformation of initial twin boundaries as well as the generation of new ones, which resulted in the development of DRX.

Sign in / Sign up

Export Citation Format

Share Document