scholarly journals Characterization by Electron Diffraction of Two Thermodynamical Phases of Precipitation in Nb-Microalloyed Steels

2005 ◽  
Vol 480-481 ◽  
pp. 489-494 ◽  
Author(s):  
Manuel Gómez ◽  
S.F. Medina ◽  
Pilar Valles ◽  
Alberto Quispe
Keyword(s):  
Mechanical Properties ◽  
Electron Microscope ◽  
Electron Diffraction ◽  
Electron Diffraction Study ◽  
High Strength ◽  
Lattice Parameters ◽  
Microalloyed Steels ◽  
Mean Values ◽  
Transmission Electron ◽  
Analytical System

Excellent mechanical properties (high strength and toughness) of microalloyed steels are mainly caused by induced precipitation during thermomechanical treatment (TMT) and grain refinement. It has been recently found that TMT of Nb-microalloyed steels can give rise to two different kinds of precipitates, manifested by the double plateau in the statically recrystallised fraction (Xa) against time curves. This work presents an electron diffraction study performed in a transmission electron microscope, equipped with an EDS analytical system. Lattice parameters of a great deal of particles, smaller than 200 nm and with face cubic centred structure, have been measured. Frequency distribution of the values of lattice parameters shows that these are grouped in two sets whose mean values are close. Comparison of these values with those found in the literature for carbides, nitrides and carbonitrides usually present in microalloyed steels demonstrates that they are Nb carbonitrides with slight stoichiometric differences (NbCxNy).

In situ electron diffraction study of synthetic (Ca1-xSrx)2MgSi2O7 åkermanites

2000 ◽  
Vol 215 (9) ◽  
Author(s):  
H. Rager ◽  
M. Schosnig ◽  
A.K. Schaper ◽  
A. Kutoglu ◽  
W. Treutmann
Keyword(s):  
Phase Transitions ◽  
Electron Microscope ◽  
Electron Diffraction ◽  
Diffraction Study ◽  
Solid Solutions ◽  
Transmission Electron Microscope ◽  
Electron Diffraction Study ◽  
Modulated Structure ◽  
Transmission Electron

This paper deals with transmission electron microscope experiments of Ca,Sr-åkermanite solid solutions at temperatures between 100 K and 375 K. The aim of the investigations was to study the compositional and temperature dependence of phase transitions from the normal to the incommensurately modulated structure of(Ca

Microstructure and Mechanical Properties of Twinning M/A Islands in a X100 High Strength Pipeline Steel

2017 ◽  
Vol 896 ◽  
pp. 182-189 ◽  
Author(s):  
Ji Ming Zhang ◽  
Qiang Chi ◽  
Ling Kang Ji ◽  
Hui Feng ◽  
Yan Hua Li ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Electron Microscope ◽  
Volume Fraction ◽  
Pipeline Steel ◽  
High Strength ◽  
Pipeline Steels ◽  
Transmission Electron ◽  
Fine Microstructure ◽  
X100 Pipeline Steel ◽  
Deformation Hardening

Fine microstructure of twinning Martensite/austenite (M/A) islands in a X100 high strength pipeline steel were analyzed by the scanning electron microscope (SEM) and high-resolution transmission electron microscope (HRTEM), and a uniaxial compressive experiment of micro-pillar for a twinning M/A island was conducted in present paper. The experimental results showed that M/A islands in X100 pipeline steels were consisted of retained austenite and nanoscale twins with sizes of less than ten nanometers. There were a few small blocks of nanoscale twins in an M/A island. Volume fraction of twinning M/A islands had an important effect on mechanical properties of X100 pipeline steels, with the increase of twinning M/A islands fraction, yield strength of X100 pipeline steel increased, and impact toughness of X100 pipeline steel decreased. The micro-pillar compression showed that the nanoscale twinning M/A island exhibited the higher deformation hardening during the compressive test, and its uniaxial compressive strength could up to 1.35GPa ultrahigh stress level.

A transmission electron microscope and electron diffraction study of carbon nanodisks

Carbon ◽  
2008 ◽  
Vol 46 (12) ◽  
pp. 1535-1543 ◽  
Author(s):  
Torgunn Garberg ◽  
Stine Nalum Naess ◽  
Geir Helgesen ◽  
Kenneth D. Knudsen ◽  
Gunnar Kopstad ◽  
...  
Keyword(s):  
Electron Microscope ◽  
Electron Diffraction ◽  
Diffraction Study ◽  
Transmission Electron Microscope ◽  
Electron Diffraction Study ◽  
Transmission Electron

Characterization of submicrometer fluid Inclusions in minerals by Analytical/Transmission Electron Microscopy and electron diffraction

1990 ◽  
Vol 48 (4) ◽  
pp. 424-424
Author(s):  
George Guthrie ◽  
David Veblen
Keyword(s):  
Electron Microscopy ◽  
Transmission Electron Microscopy ◽  
Electron Microscope ◽  
Electron Diffraction ◽  
Light Microscopy ◽  
Fluid Inclusions ◽  
Energy Dispersive Spectrometer ◽  
Analytical Transmission Electron Microscopy ◽  
Transmission Electron

The nature of a geologic fluid can often be inferred from fluid-filled cavities (generally <100 μm in size) that are trapped during the growth of a mineral. A variety of techniques enables the fluids and daughter crystals (any solid precipitated from the trapped fluid) to be identified from cavities greater than a few micrometers. Many minerals, however, contain fluid inclusions smaller than a micrometer. Though inclusions this small are difficult or impossible to study by conventional techniques, they are ideally suited for study by analytical/ transmission electron microscopy (A/TEM) and electron diffraction. We have used this technique to study fluid inclusions and daughter crystals in diamond and feldspar.Inclusion-rich samples of diamond and feldspar were ion-thinned to electron transparency and examined with a Philips 420T electron microscope (120 keV) equipped with an EDAX beryllium-windowed energy dispersive spectrometer. Thin edges of the sample were perforated in areas that appeared in light microscopy to be populated densely with inclusions. In a few cases, the perforations were bound polygonal sides to which crystals (structurally and compositionally different from the host mineral) were attached (Figure 1).

An Electron Diffraction Study on Litnerized Potato Starch

1990 ◽  
Vol 48 (1) ◽  
pp. 580-581
Author(s):  
Jean-Claude Jésior ◽  
Roger Vuong ◽  
Henri Chanzy
Keyword(s):  
Electron Microscope ◽  
Electron Diffraction ◽  
Signal To Noise Ratio ◽  
Potato Starch ◽  
Image Intensifier ◽  
Electron Diffraction Study ◽  
Starch Granules ◽  
X Ray ◽  
Individual Grains ◽  
Diamond Knife

Starch is arranged in a crystalline manner within its storage granules and should thus give sharp X-ray diagrams. Unfortunately most of the common starch granules have sizes between 1 and 100μm, making them too small for an X-ray study on individual grains. There is only one instance where an oriented X-ray diagram could be obtained on one sector of an individual giant starch granule. Despite their small size, starch granules are still too thick to be studied by electron diffraction with a transmission electron microscope. The only reported study on starch ultrastructure using electron diffraction on frozen hydrated material was made on small fragments. The present study has been realized on thin sectioned granules previously litnerized to improve the signal to noise ratio.Potato starch was hydrolyzed for 10 days in 2.2N HCl at 35°C, dialyzed against water until neutrality and embedded in Nanoplast. Sectioning was achieved with a commercially available low-angle “35°” diamond knife (Diatome) after a very carefull trimming and a pre-sectioning with a classical “45°” diamond knife. Sections obtained at a final sectioning angle of 42.2° (compared with the usual 55-60°) and at a nominal thickness of 900Å were collected on a Formvar-carbon coated grid. The exact location of the starch granules in their sections was recorded by optical microscopy on a Zeiss Universal polarizing microscope (Fig. 1a). After rehydration at a relative humidity of 95% for 24 hours they were mounted on a Philips cryoholder and quench frozen in liquid nitrogen before being inserted under frozen conditions in a Philips EM 400T electron microscope equipped with a Gatan anticontaminator and a Lhesa image intensifier.

Metallic Nanoneedles Arrays for TEM Sample Preparation “Lift-Out”

2012 ◽  
Author(s):  
Romaneh Jalilian ◽  
David Mudd ◽  
Neil Torrez ◽  
Jose Rivera ◽  
Mehdi M. Yazdanpanah ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Electron Microscope ◽  
Sample Preparation ◽  
Focused Ion Beam ◽  
Ion Beam ◽  
Beam System ◽  
Transmission Electron ◽  
Nanoneedle Array ◽  
Superior Mechanical Properties ◽  
And Performance

Abstract The sample preparation for transmission electron microscope can be done using a method known as "lift-out". This paper demonstrates a method of using a silver-gallium nanoneedle array for a quicker sharpening process of tungsten probes with better sample viewing, covering the fabrication steps and performance of needle-tipped probes for lift-out process. First, an array of high aspect ratio silver-gallium nanoneedles was fabricated and coated to improve their conductivity and strength. Then, the nanoneedles were welded to a regular tungsten probe in the focused ion beam system at the desired angle, and used as a sharp probe for lift-out. The paper demonstrates the superior mechanical properties of crystalline silver-gallium metallic nanoneedles. Finally, a weldless lift-out process is described whereby a nano-fork gripper was fabricated by attaching two nanoneedles to a tungsten probe.

Physical Simulation of Weldability of Weldox 1300 Steel

2013 ◽  
Vol 762 ◽  
pp. 551-555 ◽  
Author(s):  
Marek Stanislaw Węglowski ◽  
Marian Zeman ◽  
Miroslaw Lomozik
Keyword(s):  
Mechanical Properties ◽  
Impact Toughness ◽  
Physical Simulation ◽  
High Strength ◽  
Parent Material ◽  
Cooling Time ◽  
Electron Microscopies ◽  
Transmission Electron ◽  
Transformation Diagrams ◽  
The Impact

In the present study, the investigation of weldability of new ultra-high strength - Weldox 1300 steel has been presented. The thermal simulated samples were used to investigate the effect of welding cooling time t8/5 on the microstructure and mechanical properties of the heat affected zone (HAZ). In the frame of these investigation the microstructure was studied by the light (LM) and transmission electron microscopies (TEM). It has been shown that the microstructure of the Weldox 1300 steel is composed of tempered martensite, and inside the laths the minor precipitations mainly V(CN) and molybdenum carbide Mo2C were observed. Mechanical properties of parent material were analysed by the tensile, impact and hardness tests. In details the influence of cooling time in the range of 2,5 - 300 s. on hardness, impact toughness and microstructure of simulated HAZ was studied by using welding thermal simulation test. The results show that the impact toughness and hardness decrease with the increase of t8/5 under the condition of a single thermal cycle in simulated HAZ. The continuous cooling transformation diagrams (CCT-W for welding conditions) of Weldox 1300 steel for welding purposes was also elaborated. The steel Weldox 1300 for cooling time in the range of 2,5 - 4 s showed martensite microstructure, for time from 4 s to 60 s mixture of martensite and bainite, and for longer cooling time mixture of ferrite, bainite and martensite. The results indicated that the weldability of Weldox 1300 steel is limited and to avoid the cold cracking the preheating procedure or medium net linear heat input should be used.

Sign in / Sign up

Export Citation Format

Share Document