Electrically Conductive and Wear Resistant Si3N4-Based Composites with TiC0.5N0.5 Particles for Electrical Discharge Machining

2005 ◽  
Vol 492-493 ◽  
pp. 27-32 ◽  
Author(s):  
Dongtao Jiang ◽  
Jef Vleugels ◽  
Omer Van der Biest ◽  
Wei Dong Liu ◽  
Raf Verheyen ◽  
...  
Keyword(s):  
Hot Pressing ◽  
Electrical Discharge ◽  
Material Removal ◽  
Bending Strength ◽  
Electrical Discharge Machining ◽  
Removal Rate ◽  
Strong Anisotropy ◽  
Electrically Conductive ◽  
Wear Resistant ◽  
Lower Material

Electrically conductive and wear resistant Si3N4-based composites were developed in order to facilitate electrical discharge machining (EDM). The microstructural and mechanical properties of Si3N4-based composites with different amounts of TiC0.5N0.5, fabricated by hot pressing at 1650°C for 1 hour, are investigated and evaluated. The hardness of the micron-sized TiC0.5N0.5 powder based composites increased with increasing TiC0.5N0.5 content from 20 up to 40 vol. %, whereas the bending strength decreased. The fracture toughness reached a maximum at 30 vol. % TiC0.5N0.5 and exhibits a strong anisotropy with respect to the hot-pressing direction. The EDM behaviour of the composites is strongly influenced by the TiC0.5N0.5 content. The composites with a higher TiC0.5N0.5 content have a lower material removal rate but a better surface quality.

Processing EC-PCD by Constant-Force Grinding Assisted with EDM

2010 ◽  
Vol 126-128 ◽  
pp. 645-650
Author(s):  
Gaku Sugino ◽  
Manabu Iwai ◽  
Tadakazu Sano ◽  
Shinichi Ninomiya ◽  
Kiyoshi Suzuki
Keyword(s):  
Electrical Discharge ◽  
Material Removal ◽  
High Efficiency ◽  
Electrical Discharge Machining ◽  
Removal Rate ◽  
Surface Condition ◽  
Grinding Force ◽  
Constant Force ◽  
Wheel Wear ◽  
Electrically Conductive

A new PCD (electrically conductive PCD: EC-PCD) consisting of electrically conductive diamond particles has recently been developed. The authors have proposed a complex grinding assisted with electrical discharge machining (EDM) where discharge machining and grinding are used in combination during material removal to realize high efficiency, low and stable grinding force and low wheel wear for the EC-PCD. In this study, the effect of constant-force grinding in a complex grinding assisted with electrical discharge machining of EC-PCD was investigated. As a result, it was found that higher material removal rate, higher grinding ratio and better surface condition were obtained on EC-PCD compared with standard PCD (S-PCD) in the constant-force grinding.

Optimization of μEDM process assisted with rotating magnetic pulling force and ultrasonic vibration

2021 ◽  
pp. 095440892098440
Author(s):  
Gurpreet Singh ◽  
DR Prajapati ◽  
PS Satsangi
Keyword(s):  
Ultrasonic Vibration ◽  
Material Removal Rate ◽  
Electrical Discharge ◽  
Material Removal ◽  
Electrical Discharge Machining ◽  
Removal Rate ◽  
Machining Process ◽  
Micro Electrical Discharge Machining ◽  
Pulling Force ◽  
Tool Rotation

The micro-electrical discharge machining process is hindered by low material removal rate and low surface quality, which bound its capability. The assistance of ultrasonic vibration and magnetic pulling force in micro-electrical discharge machining helps to overcome this limitation and increase the stability of the machining process. In the present research, an attempt has been made on Taguchi based GRA optimization for µEDM assisted with ultrasonic vibration and magnetic pulling force while µEDM of SKD-5 die steel with the tubular copper electrode. The process parameters such as ultrasonic vibration, magnetic pulling force, tool rotation, energy and feed rate have been chosen as process variables. Material removal rate and taper of the feature have been selected as response measures. From the experimental study, it has been found that response output measures have been significantly improved by 18% as compared to non assisted µEDM. The best optimal combination of input parameters for improved performance measures were recorded as machining with ultrasonic vibration (U1), 0.25 kgf of magnetic pulling force (M1), 600 rpm of tool rotation (R2), 3.38 mJ of energy (E3) and 1.5 mm/min of Tool feed rate (F3). The confirmation trail was also carried out for the validation of the results attained by Grey Relational Analysis and confirmed that there is a substantial improvement with both assistance applied simultaneously.

Investigation of the Spark Cycle Effect on Material Removal Rate in Wire Electrical Discharge Machining

Manufacturing ◽  
2003 ◽  
Author(s):  
Scott F. Miller ◽  
Albert J. Shih
Keyword(s):  
Process Parameters ◽  
Material Removal Rate ◽  
Electrical Discharge ◽  
Material Removal ◽  
Electrical Discharge Machining ◽  
Removal Rate ◽  
Short Circuit ◽  
Wire Electrical Discharge Machining ◽  
Time Duration ◽  
Edm Process

The development of new, advanced engineering materials and the needs for precise and flexible prototype and low-volume production have made wire electrical discharge machining (EDM) an important manufacturing process to meet such demand. This research investigates the effect of spark on-time duration and spark on-time ratio, two important EDM process parameters, on the material removal rate (MRR) and surface integrity of four types of advanced material: porous metal foams, metal bond diamond grinding wheels, sintered Nd-Fe-B magnets, and carbon-carbon bipolar plates. An experimental procedure was developed. During the wire EDM, five types of constraints on the MRR due to short circuit, wire breakage, machine slide speed limit, and spark on-time upper and lower limits have been identified. An envelope of feasible EDM process parameters is created and compared across different work-materials. Applications of such process envelope to select process parameters for maximum MRR and for machining of micro features are presented.

scholarly journals The Effect of Discharge Current and Pulse-On Time on Biocompatible Zr-based BMG Sinking-EDM

2020 ◽  
Vol 10 (1) ◽  
pp. 401-407
Author(s):  
Yanuar Rohmat Aji Pradana ◽  
Aldi Ferara ◽  
Aminnudin Aminnudin ◽  
Wahono Wahono ◽  
Jason Shian-Ching Jang
Keyword(s):  
Surface Roughness ◽  
Metallic Glasses ◽  
Electrical Discharge ◽  
Material Removal ◽  
Electrical Discharge Machining ◽  
Removal Rate ◽  
Surface Hardness ◽  
Recast Layer ◽  
Surface Evaporation ◽  
Pulse On Time

AbstractThe machinability information of Zr-based bulk metallic glasses (BMGs) are recently limited but essential to provide technological recommendation for the fabrication of the medical devices due to the material’s metastable nature. This study aims to investigate the material removal rate (MRR) and surface roughness under different current and pulse-on time of newly developed Ni- and Cu-free Zr-based BMG using sinking-electrical discharge machining (EDM). By using weightloss calculation, surface roughness test and scanning electron microscopy (SEM) observation on the workpiece after machining, both MRR and surface roughness were obtained to be increased up to 0.594 mm3/min and 5.50 μm, respectively, when the higher current was applied. On the other hand, the longer pulse-on time shifted the Ra into the higher value but lower the MRR value to only 0.183 mm3/min at 150 μs. Contrary, the surface hardness value was enhanced by both higher current and pulse-on time applied during machining indicating different level of structural change after high-temperature spark exposure on the BMG surface. These phenomena are strongly related to the surface evaporation which characterize the formation of crater and recast layer in various thicknesses and morphologies as well as the crystallization under the different discharge energy and exposure time.

Experimental Study of Machining of Shape Memory Alloys Using Dry Micro Electrical Discharge Machining Process

2018 ◽  
Author(s):  
Sagil James ◽  
Sharadkumar Kakadiya
Keyword(s):  
Shape Memory Alloys ◽  
Shape Memory ◽  
Electrical Discharge ◽  
Material Removal ◽  
Electrical Discharge Machining ◽  
Removal Rate ◽  
Dielectric Medium ◽  
Machining Process ◽  
Machining Processes ◽  
Micro Electrical Discharge Machining

Shape Memory Alloys are smart materials that tend to remember and return to its original shape when subjected to deformation. These materials find numerous applications in robotics, automotive and biomedical industries. Micromachining of SMAs is often a considerable challenge using conventional machining processes. Micro-Electrical Discharge Machining is a combination of thermal and electrical processes, which can machine any electrically conductive material at micron scale independent of its hardness. It employs dielectric medium such as hydrocarbon oils, deionized water, and kerosene. Using liquid dielectrics has adverse effects on the machined surface causing cracking, white layer deposition, and irregular surface finish. These limitations can be minimized by using a dry dielectric medium such as air or nitrogen gas. This research involves the experimental study of micromachining of Shape Memory Alloys using dry Micro-Electrical Discharge Machining process. The study considers the effect of critical process parameters including discharge voltage and discharge current on the material removal rate and the tool wear rate. A comparison study is performed between the Micro-Electrical Discharge Machining process with using the liquid as well as air as the dielectric medium. In this study, microcavities are successfully machined on shape memory alloys using dry Micro-Electrical Discharge Machining process. The study found that the dry Micro-Electrical Discharge Machining produces a comparatively better surface finish, has lower tool wear and lesser material removal rate compared to the process using the liquid as the dielectric medium. The results of this research could extend the industrial applications of Micro Electrical Discharge Machining processes.

Machining Feasibility of a New Developed Medium in Electrical Discharge Machining

2015 ◽  
Vol 656-657 ◽  
pp. 335-340 ◽  
Author(s):  
Fang Pin Chuang ◽  
Yan Cherng Lin ◽  
Hsin Min Lee ◽  
Han Ming Chow ◽  
A. Cheng Wang
Keyword(s):  
Electrical Discharge ◽  
Material Removal ◽  
Electrical Discharge Machining ◽  
Removal Rate ◽  
Environmentally Friendly ◽  
Industrial Applications ◽  
Deionized Water ◽  
Machining Parameters ◽  
Machining Performance ◽  
Machining Characteristics

The environment issue and green machining technique have been induced intensive attention in recent years. It is urgently need to develop a new kind dielectric to meet the requirements for industrial applications. The aim of this study is to develop a novel dielectric using gas media immersed in deionized water for electrical discharge machining (EDM). The developed machining medium for EDM can fulfill the environmentally friendly issue and satisfy the demand of high machining performance. The experiments were conducted by this developed medium to investigate the effects of machining parameters on machining characteristics in terms of material removal rate (MRR) and surface roughness. The developed EDM medium revealed the potential to obtain a stabilizing progress with excellent machining performance and environmentally friendly feature.

CHARACTERIZATION OF ZrB2-SiC COMPOSITES WITH AN ANALYTICAL STUDY ON MATERIAL REMOVAL RATE AND TOOL WEAR RATE DURING ELECTRICAL DISCHARGE MACHINING

2016 ◽  
Vol 40 (3) ◽  
pp. 331-349 ◽  
Author(s):  
S. Sivasankar ◽  
R. Jeyapaul
Keyword(s):  
Wear Rate ◽  
Tool Wear ◽  
Relative Density ◽  
Material Removal Rate ◽  
Electrical Discharge ◽  
Material Removal ◽  
Electrical Discharge Machining ◽  
Removal Rate ◽  
Tool Wear Rate ◽  
Tool Materials

This research work concentrates on Electrical Discharge Machining (EDM) performance evaluation of ZrB2- SiC ceramic matrix composites with different tool materials at various machining parameters. Monolithic ZrB2 possesses lower relative density (98.72%) than composites. ZrB2 with 20 Vol.% of SiC possesses 99.74% of the relative density with improved hardness values. Bend strength and Young’s modulus increase with SiC addition until it reaches 20 Vol% and then decreasing. EDM performance on tool materials of tungsten, niobium, tantalum, graphite and titanium at various levels of pulse on time and pulse off time are analyzed. Graphite produces the best Material removal rate (MRR) for all the workpieces. Tool wear rate decreases with melting point and thermal conductivity of the tool material.

scholarly journals Investigation an assisting electrode powder mixed electrical discharge machining of nonconductive ceramic

2021 ◽  
Author(s):  
Dragan Rodic ◽  
Marin Gostimirovic ◽  
Milenko Sekulic ◽  
Borislav Savkovic ◽  
Branko Strbac
Keyword(s):  
Surface Roughness ◽  
Tool Wear ◽  
Material Removal Rate ◽  
Electrical Discharge ◽  
Material Removal ◽  
Metal Removal ◽  
Electrical Discharge Machining ◽  
Removal Rate ◽  
Positive Effects ◽  
Assisting Electrode

Abstract It is well known that electrical discharge machining can be used in the processing of nonconductive materials. In order to improve the efficiency of machining modern engineering materials, existing electrical discharge machines are constantly being researched and improved or developed. The current machining of non-conductive materials is limited due to the relatively low material removal rate and high surface roughness. A possible technological improvement of electrical discharge machining can be achieved by innovations of existing processes. In this paper, a new approach for machining zirconium oxide is presented. It combines electrical discharge machining with assisting electrode and powder-mixed dielectric. The assisting electrode is used to enable electrical discharge machining of nonconductive material, while the powder-mixed dielectric is used to increase the material removal rate, reduce surface roughness, and decrease relative tool wear. The response surface method was used to generate classical mathematical models, analyzing the output performances of surface roughness, material removal rate and relative tool wear. Verification of the obtained models was performed based on a set of new experimental data. By combining these latest techniques, positive effects on machining performances are obtained. It was found that the surface roughness was reduced by 18%, the metal removal rate was increased by about 12% and the relative tool wear was reduced by up to 6% compared to electrical discharge machining with supported electrode without powder.

Fabrication and experimental investigation of magnetic field assisted powder mixed electrical discharge machining on machining of aluminum 6061 alloy

2019 ◽  
Vol 233 (12) ◽  
pp. 2283-2291 ◽  
Author(s):  
Arun Kumar Rouniyar ◽  
Pragya Shandilya
Keyword(s):  
Magnetic Field ◽  
Wear Rate ◽  
Tool Wear ◽  
Material Removal Rate ◽  
Electrical Discharge ◽  
Material Removal ◽  
Electrical Discharge Machining ◽  
Removal Rate ◽  
Tool Wear Rate ◽  
Pulse On Time

Magnetic field assisted powder mixed electrical discharge machining is a hybrid machining process with suitable modification in electrical discharge machining combining the use of magnetic field and fine powder in the dielectric fluid. Aluminum 6061 alloy has found highly significance for the advanced industries like automotive, aerospace, electrical, marine, food processing and chemical due to good corrosion resistance, high strength-to-weight ratio, ease of weldability. In this present work, magnetic field assisted powder mixed electrical discharge machining setup was fabricated and experiments were performed using one factor at a time approach for aluminum 6061 alloy. The individual effect of machining parameters namely, peak current, pulse on time, pulse off time, powder concentration and magnetic field on material removal rate and tool wear rate was investigated. The effect of peak current was found to be dominant on material removal rate and tool wear rate followed by pulse on time, powder concentration and magnetic field. Increase in material removal rate and tool wear rate was observed with increase in peak current, pulse on time and a decrease in pulse off time, whereas, for material removal rate increases and tool wear rate decreases up to the certain value and follow the reverse trend with an increase in powder concentration. Material removal rate was increased and tool wear rate was decreased with increase in magnetic field.

Sign in / Sign up

Export Citation Format

Share Document