Texture of Al-Cu Alloys Deformed by ECAP

2005 ◽  
Vol 495-497 ◽  
pp. 851-856 ◽  
Author(s):  
Jan Kuśnierz ◽  
Marie Helene Mathon ◽  
Thierry Baudin ◽  
Zdzislaw Jasieński ◽  
Richard Penelle
Keyword(s):  
Grain Size ◽  
Aluminium Alloys ◽  
Superplastic Forming ◽  
Orientation Distribution ◽  
Coarse Grained ◽  
Fine Grained ◽  
Angular Pressing ◽  
Cu Alloys ◽  
Super Plastic ◽  
Short Time

Materials of ultra-fine grained microstructure (sub-micrometer grain size) exhibit large strength, hardness and ductility and also the increased toughness in comparison with conventional coarse-grained ones. In these materials also the super-plastic flow at lower temperatures is observed. This behaviour may be interesting when aluminium alloys like AlCuZr, used in superplastic forming, are considered. In the paper, the methods of preparing such materials by equal-channel angular pressing (ECAP) is proposed and the texture analysis, based on neutron diffraction pole figure measurements and calculated orientation distribution function of two alloys AlCu4SiMn and AlCu5AgMgZr is discussed. The influence of short time recrystallization is discussed in relation with TEM and SEM observations.

Cavitation Behavior of Ultra-Fine Grained Ti-6Al-4V Alloy Produced by Equal-Channel Angular Pressing

2007 ◽  
Vol 551-552 ◽  
pp. 621-626
Author(s):  
Young Gun Ko ◽  
Yong Nam Kwon ◽  
Jung Hwan Lee ◽  
Dong Hyuk Shin ◽  
Chong Soo Lee
Keyword(s):  
Grain Size ◽  
Strain Rate ◽  
Equal Channel Angular Pressing ◽  
Cavity Growth ◽  
Rate Sensitivity ◽  
Theoretical Models ◽  
Coarse Grained ◽  
Fine Grained ◽  
Angular Pressing ◽  
Cavitation Behavior

Cavitation behavior during superplastic flow of ultra-fine grained (UFG) Ti-6Al-4V alloy was established with the variation of grain size and misorientation. After imposing an effective strainup to 8 via equal-channel angular pressing (ECAP) at 873 K, alpha-phase grains were markedly refined from 11 μm to ≈ 0.3 μm, and misorientation angle was increased. Uniaxial-tension tests were conducted for initial coarse grained (CG) and two UFG alloys (ε = 4 and 8) at temperature of 973 K and strain rate of 10-4 s-1. Quantitative measurements of cavitation evidenced that both the average size and the area fraction of cavities significantly decreased with decreasing grain size and/or increasing misorientation. It was also found that, when compared to CG alloy, cavitation as well as diffused necking was less prevalent in UFG alloys, which was presumably due to the higher value of strain-rate sensitivity. Based on the several theoretical models describing the cavity growth behavior, the cavity growth mechanism in UFG alloys was suggested.

scholarly journals The Effect of Initial Grain Size on Formability of AZ31B Magnesium Alloy during I-ECAP

2014 ◽  
Vol 611-612 ◽  
pp. 573-580 ◽  
Author(s):  
Michal Gzyl ◽  
Andrzej Rosochowski ◽  
Lech Olejnik ◽  
Aleksey Reshetov
Keyword(s):  
Grain Size ◽  
Magnesium Alloy ◽  
Strong Influence ◽  
Coarse Grained ◽  
Rolled Plate ◽  
Processing Temperature ◽  
Az31b Magnesium Alloy ◽  
Fine Grained ◽  
Angular Pressing ◽  
Logarithmic Equation

The goal of this work was to investigate formability of AZ31B magnesium alloy during incremental equal channel angular pressing (I-ECAP). Square billets were processed using different routes of I-ECAP at temperatures varying from 125 °C to 250 °C. The billets were obtained from commercially available coarse-grained, hot-extruded rod and fine-grained, hot-rolled plate. A strong influence of the initial microstructure on processing temperature was reported. Fine-grained samples were successfully processed at 200 °C, while coarse-grained ones must have been heated up to 250 °C to avoid fracture. A gradual temperature decrease with subsequent passes allowed successful pressing at 150 °C. Processing using various routes of I-ECAP showed that a billet rotation before the last pass had strong influence on mechanical properties. The results of experiments were plotted on the diagram of allowable processing temperature for AZ31B. It was found that the relation between the minimum temperature in I-ECAP and the initial grain size could be described by a logarithmic equation.

Effect of Microstructure on Impact Energy of an Al-Mg-Sc Alloy

2016 ◽  
Vol 877 ◽  
pp. 421-426
Author(s):  
Daria Zhemchuzhnikova ◽  
Rustam Kaibyshev
Keyword(s):  
Grain Size ◽  
Impact Toughness ◽  
Impact Energy ◽  
Coarse Grained ◽  
Fine Grained ◽  
Angular Pressing ◽  
Average Grain Size ◽  
Coarse Grained State ◽  
Hot Rolled ◽  
The Impact

Analysis of the absorbed impact energy of an Al-Mg-Sc alloy after different thermo-mechanical processing routes was investigated between-196°C and 20°C. The material with a grain size of ∼ 22 μm in cast condition and with an average grain size of 0.7 μm produced by was produced by equal-channel angular pressing (ECAP) exhibits well-defined ductile-brittle transition in the temperature interval-60...-100°C, however, even at-196°C the value impact energy of fine-grained alloy is higher by a factor of 2 in comparison with coarse-grained state. The impact toughness of the hot rolled alloy linearly decreases with decreasing temperature. The influence of different microstructures on impact toughness and fracture behavior of alloy is discussed.

scholarly journals Submarine lava deltas of the 2018 eruption of Kīlauea volcano

2021 ◽  
Vol 83 (4) ◽  
Author(s):  
S. Adam Soule ◽  
Michael Zoeller ◽  
Carolyn Parcheta
Keyword(s):  
Grain Size ◽  
Pore Pressure ◽  
Mechanistic Model ◽  
Large Fraction ◽  
Volcanic Hazards ◽  
Lava Flows ◽  
Coarse Grained ◽  
Fine Grained ◽  
Fine Grain ◽  
Delta Formation

AbstractHawaiian and other ocean island lava flows that reach the coastline can deposit significant volumes of lava in submarine deltas. The catastrophic collapse of these deltas represents one of the most significant, but least predictable, volcanic hazards at ocean islands. The volume of lava deposited below sea level in delta-forming eruptions and the mechanisms of delta construction and destruction are rarely documented. Here, we report on bathymetric surveys and ROV observations following the Kīlauea 2018 eruption that, along with a comparison to the deltas formed at Pu‘u ‘Ō‘ō over the past decade, provide new insight into delta formation. Bathymetric differencing reveals that the 2018 deltas contain more than half of the total volume of lava erupted. In addition, we find that the 2018 deltas are comprised largely of coarse-grained volcanic breccias and intact lava flows, which contrast with those at Pu‘u ‘Ō‘ō that contain a large fraction of fine-grained hyaloclastite. We attribute this difference to less efficient fragmentation of the 2018 ‘a‘ā flows leading to fragmentation by collapse rather than hydrovolcanic explosion. We suggest a mechanistic model where the characteristic grain size influences the form and stability of the delta with fine grain size deltas (Pu‘u ‘Ō‘ō) experiencing larger landslides with greater run-out supported by increased pore pressure and with coarse grain size deltas (Kīlauea 2018) experiencing smaller landslides that quickly stop as the pore pressure rapidly dissipates. This difference, if validated for other lava deltas, would provide a means to assess potential delta stability in future eruptions.

Effect of Equal-Channel Angular Pressing (ECAP) on Creep in Aluminium Alloys

2007 ◽  
Vol 539-543 ◽  
pp. 2904-2909 ◽  
Author(s):  
Vàclav Sklenička ◽  
Jiří Dvořák ◽  
Marie Kvapilová ◽  
Milan Svoboda ◽  
Petr Král ◽  
...  
Keyword(s):  
Equal Channel Angular Pressing ◽  
Aluminium Alloys ◽  
Creep Resistance ◽  
Room Temperature ◽  
Creep Behaviour ◽  
Coarse Grained ◽  
Pure Aluminium ◽  
Creep Tests ◽  
Angular Pressing ◽  
Compression Creep

This paper examines the effect of equal-channel angular pressing (ECAP) on creep behaviour of pure aluminium, binary Al-0.2wt.%Sc alloy and ternary Al-3wt.%Mg-0.2wt.%Sc alloy. The ECAP was conducted at room temperature with a die that had a 90° angle between the channels and 8 repetitive ECAP passes followed route BC. Constant stress compression creep tests were performed at 473 K and stresses ranging between 16 to 80 MPa on ECAP materials and, for comparison purposes, on the initial coarse-grained materials. The results showed that the creep resistance of the ECAP processed Al-Sc and Al-Mg-Sc alloys was markedly deteriorated with respect to unpressed coarse-grained materials.

scholarly journals Investigation on the Microstructure of ECAP-Processed Iron-Aluminium Alloys

Materials ◽  
2021 ◽  
Vol 14 (1) ◽  
pp. 219
Author(s):  
Bernd-Arno Behrens ◽  
Kai Brunotte ◽  
Tom Petersen ◽  
Roman Relge
Keyword(s):  
Grain Refinement ◽  
Aluminium Alloys ◽  
Aluminium Content ◽  
Microstructure Development ◽  
Chamber Furnace ◽  
Fine Grained ◽  
Angular Pressing ◽  
Ecap Process ◽  
Average Grain Size ◽  
Forming Temperature

The present work deals with adjusting a fine-grained microstructure in iron-rich iron-aluminium alloys using the ECAP-process (Equal Channel Angular Pressing). Due to the limited formability of Fe-Al alloys with increased aluminium content, high forming temperatures and low forming speeds are required. Therefore, tool temperatures above 1100 °C are permanently needed to prevent cooling of the work pieces, which makes the design of the ECAP-process challenging. For the investigation, the Fe-Al work pieces were heated to the respective hot forming temperature in a chamber furnace and then formed in the ECAP tool at a constant punch speed of 5 mm/s. Besides the chemical composition (Fe9Al, Fe28Al and Fe38Al (at.%—Al)), the influences of a subsequent heat treatment and the holding time on the microstructure development were investigated. For this purpose, the average grain size of the microstructure was measured using the AGI (Average Grain Intercept) method and correlated with the aforementioned parameters. The results show that no significant grain refinement could be achieved with the parameters used, which is largely due to the high forming temperature significantly promoting grain growth. The holding times in the examined area do not have any influence on the grain refinement.

Tensile Ductility of Ultra-Fine Grained Copper at High Strain Rate

2010 ◽  
Vol 160-162 ◽  
pp. 260-266 ◽  
Author(s):  
Tao Suo ◽  
Kui Xie ◽  
Yu Long Li ◽  
Feng Zhao ◽  
Qiong Deng
Keyword(s):  
High Strain Rate ◽  
Strain Rate ◽  
High Strain ◽  
Testing Machine ◽  
Coarse Grained ◽  
Dislocation Dynamic ◽  
Pressing Method ◽  
Fine Grained ◽  
Angular Pressing ◽  
Split Hopkinson

In this paper, ultra-fine grained copper fabricated by equal channel angular pressing method and annealed coarse grained copper were tensioned under both quasi-static and dynamic loading conditions using an electronic universal testing machine and the split Hopkinson tension bar respectively. The rapture surface of specimen was also observed via a Scanning Electron Microscope (SEM). The experimental results show that the ductility of polycrystalline copper decreases remarkably due to the grain refinement. However, with the increase of applied strain rate, ductility of the UFG-Cu is enhanced. The fracture morphologies also give the evidence of enhanced ductility of UFG-Cu at high strain rate. It is believed the enhanced ductility of UFG materials at high strain rate can be attributed to the restrained dislocation dynamic recovery.

Deformation Size Effects Due to Specimen and Grain Size in Microbending

2010 ◽  
Vol 132 (1) ◽  
Author(s):  
Sunal Ahmet Parasiz ◽  
Reid VanBenthysen ◽  
Brad L. Kinsey
Keyword(s):  
Grain Size ◽  
Sheet Thickness ◽  
Specimen Size ◽  
Coarse Grained ◽  
Thick Sheet ◽  
Hardness Profile ◽  
Localized Deformation ◽  
Fine Grained ◽  
Deformation Distribution ◽  
Deformation Area

Sheet metal forming often consists of bending processes in which gradients of deformation exists through the thickness of the workpiece in a localized deformation area. In microscale bending, these deformation gradients become much steeper, as the changes in the deformation occur over short distances (in the order of micrometers). In addition, with miniaturization, the number of grains that are present through the thickness decreases significantly. In this research, the effect of grain size and specimen size on the deformation distribution through the thickness of microbent sheet specimens was investigated via microhardness evaluations. It was found that the deformation distribution, i.e., hardness profile, is not affected significantly by the grain size when the sheet thickness is large (for 1.625 mm specimens) or by miniaturization of the specimen size when the grain size is fine. However, the deformation distribution of the coarse grained specimens deviates from the fine grained ones and from the 1.625 mm thick sheet specimens when the specimen size is miniaturized.

Martensitic Transformations and Functional Stability in Ultra-Fine Grained NiTi Shape Memory Alloys

2008 ◽  
Vol 584-586 ◽  
pp. 852-857 ◽  
Author(s):  
Juri Burow ◽  
Egor Prokofiev ◽  
Christoph Somsen ◽  
Jan Frenzel ◽  
Ruslan Valiev ◽  
...  
Keyword(s):  
Grain Size ◽  
Shape Memory Alloys ◽  
Shape Memory ◽  
Thermomechanical Processing ◽  
High Pressure Torsion ◽  
Martensitic Transformations ◽  
Coarse Grained ◽  
Functional Stability ◽  
Fine Grained ◽  
Niti Shape Memory Alloys

Martensitic transformations in NiTi shape memory alloys (SMAs) strongly depend on the microstructure. In the present work, we investigate how martensitic transformations are affected by various types of ultra-fine grained (UFG) microstructures resulting from various processing routes. NiTi SMAs with UFG microstructures were obtained by equal channel angular pressing, high pressure torsion, wire drawing and subsequent annealing treatments. The resulting material states were characterized by transmission electron microscopy and differential scanning calorimetry (DSC). The three thermomechanical processing routes yield microstructures which significantly differ in terms of grain size and related DSC chart features. While the initial coarse grained material shows a well defined one-step martensitic transformation on cooling, two-step transformations were found for all UFG material states. The functional stability of the various UFG microstructures was evaluated by thermal cycling. It was found that UFG NiTi alloys show a significantly higher stability. In the present work, we also provide preliminary results on the effect of grain size on the undercooling required to transform the material into B19’ and on the related heat of transformation.

scholarly journals Evolution of Adiabatic Shear Band in Ultra-Fine-Grained Iron under Dynamic Shear Loading

2010 ◽  
Vol 667-669 ◽  
pp. 761-765 ◽  
Author(s):  
Fu Ping Yuan ◽  
Xiao Lei Wu
Keyword(s):  
Grain Size ◽  
Shear Band ◽  
Adiabatic Shear Band ◽  
Shear Loading ◽  
Electron Back Scatter Diffraction ◽  
Adiabatic Shear ◽  
Dynamic Shear ◽  
Micro Hardness ◽  
Fine Grained ◽  
Angular Pressing

Ultra-fine-grained (UFG)/Nanocrystalline (NC) materials usually show reduced strain hardening and limited ductility due to formation of adiabatic shear band (ASB) under dynamic loading. In the present study, evolution of ASB in UFG Fe under dynamic shear loading was investigated. The UFG Fe was processed by equal-channel angular pressing (ECAP) via route Bc. After 6 passes, the grain size of UFG Fe reaches ~ 600 nm, as confirmed by means of Electron Back Scatter Diffraction (EBSD). Examination of micro-hardness and grain size of UFG Fe as a function of post-ECAP annealing temperature shows a transition from recovery to recrystallization at 500 0C. The high-strain-rate response of UFG Fe was characterized by hat-shaped specimen set-ups in Hopkinson bar experiments. The characteristics of ASB as a function of shear displacement, such as thickness of shear band and micro-hardness inside the shear band, were examined by SEM and Vickers micro-indentation respectively.

Sign in / Sign up

Export Citation Format

Share Document