The Analysis of SPD Paradox by Computer Modeling Technique

2009 ◽  
Vol 633-634 ◽  
pp. 231-248
Author(s):  
Igor V. Alexandrov ◽  
Roza G. Chembarisova
Keyword(s):  
Plastic Deformation ◽  
Thermal Treatment ◽  
Deformation Behavior ◽  
High Strength ◽  
High Ductility ◽  
Angular Pressing ◽  
Deformation Twins ◽  
Ultrafine Grained ◽  
Favorable Conditions ◽  
Dislocation Density Increase

The paper has viewed the manifestation of the paradox of severe plastic deformation (SPD), caused by the occurrence of preexisting deformation twins in ultrafine-grained Cu, which has been obtained by the combination of the SPD method, accomplished by an equal-channel angular pressing with the conventional methods of deformation-thermal treatment. The high strength of the obtained samples has proved to be conditioned by the occurrence of the high density of the coherent twin boundaries, serving as effective obstacles on the way of slipping dislocations. Moreover, the occurrence of the twins creates favorable conditions for the dislocation density increase both in the grains with the twins and in the grains without them. As a result the sample hardens, contributing additionally into its strength. Simultaneously it manifests high ductility. By doing so the deformation behavior of the sample is mainly conditioned by the grain boundaries of grains free from the twins. The results were obtained on the basis of the dislocation-based model which develops models of Y. Estrin and L. Tóth, M. Zehetbauer, and L. Remy.

Development of Complex Methods, Combining Thermal Treatment with Severe Plastic Deformation, for Processing of High-Strength Nanostructured Cu-1%Cr-0.7%Al Alloy

2006 ◽  
Vol 503-504 ◽  
pp. 515-520 ◽  
Author(s):  
Igor V. Alexandrov ◽  
V.V. Latysh ◽  
Sun Ig Hong ◽  
S.N. Faizova ◽  
V.M. Polovnikov
Keyword(s):  
Plastic Deformation ◽  
Thermal Treatment ◽  
Severe Plastic Deformation ◽  
High Pressure Torsion ◽  
High Strength ◽  
Al Alloy ◽  
Thermal Treatments ◽  
Angular Pressing ◽  
Ultrafine Grained ◽  
Complex Methods

The current work presents new results of investigation of properties and structure of nanocrystalline and submicrocrystalline Cu-1%Cr-0.7%Al alloy. Two severe plastic deformation (SPD) techniques were applied to refine the structure: high pressure torsion and equal-channel angular pressing (ECAP). The first technique was applied to conduct preliminary studies of the alloy different thermal treatments as before SPD as well as after it. A new technological thermomechanical technique for processing of bulk billets of Cu-1%Cr-0.7%Al alloy possessing an ultrafine grained structure was developed on the basis of the obtained results. This technique comprises a combination of ECAP and other deformational processes with the thermal treatment. High values of the tensile strength and yield stress - 700 MPa and 16% accordingly – have been obtained as a result of such treatment, whereas these values after conventional treatment consisted 450 MPa and 20% respectively.

THE PROPERTIES OF BULK ULTRAFINE-GRAINED METALS PROCESSED THROUGH THE APPLICATION OF SEVERE PLASTIC DEFORMATION

2012 ◽  
Vol 05 ◽  
pp. 299-306
Author(s):  
TERENCE G. LANGDON
Keyword(s):  
Plastic Deformation ◽  
Severe Plastic Deformation ◽  
Elevated Temperatures ◽  
High Pressure Torsion ◽  
Superplastic Forming ◽  
High Strength ◽  
Basic Principles ◽  
Angular Pressing ◽  
Ultrafine Grained ◽  
Processing Techniques

Processing through the application of severe plastic deformation (SPD) provides a very attractive tool for the production of bulk ultrafine-grained materials. These materials typically have grain sizes in the submicrometer or nanometer ranges and they exhibit high strength at ambient temperature and, if the ultrafine grains are reasonably stable at elevated temperatures, they have a potential for use in superplastic forming operations. Several procedures are now available for applying SPD to metal samples but the most promising are Equal-Channel Angular Pressing (ECAP) and High-Pressure Torsion (HPT). This paper examines the basic principles of ECAP and HPT and describes some of the properties that may be achieved using these processing techniques.

Influence of Severe Plastic Deformation on Mechanical Properties of an AA5024 Alloy

2016 ◽  
Vol 879 ◽  
pp. 1317-1322 ◽  
Author(s):  
Anna Mogucheva ◽  
Diana Yuzbekova ◽  
Tatiana Lebedkina ◽  
Mikhail Lebyodkin ◽  
Rustam Kaibyshev
Keyword(s):  
Mechanical Properties ◽  
Plastic Deformation ◽  
Severe Plastic Deformation ◽  
High Strength ◽  
Coarse Grained ◽  
Type B ◽  
Angular Pressing ◽  
Ultrafine Grained ◽  
Elongation To Failure ◽  
Dislocation Strengthening

The paper reports on the effect of severe plastic deformation on mechanical properties of an Al-4.57Mg-0.35Mn-0.2Sc-0.09Zr (in wt. pct.) alloy processed by equal channel angular pressing followed by cold rolling (CR). The sheets of the 5024 alloy with coarse grained (CG) structure exhibited a yield stress (YS) near 410 MPa and an ultimate tensile strength (UTS) of 480 MPa, while the YS and UTS of this material with ultrafine-grained (UFG) structure increased to 530 and 560 MPa, respectively. On the other hand, the elongation to failure decreased by a factor of 2 and 4 after CR and CR following ECAP, respectively. It was shown that dislocation strengthening attributed to extensive CR plays a major role in achieving high strength of this alloy. Besides these macroscopic characteristics, jerky flow caused by the Portevin-Le Chatelier (PLC) instability of plastic deformation was examined. The formation of UFG structure results in a transition from mixed type A+B to pure type B PLC serrations. No such effect on the serrations type was observed after CR.

The Flow Behavior of Ultrafine-Grained Materials

2014 ◽  
Vol 1013 ◽  
pp. 7-14
Author(s):  
Terence G. Langdon
Keyword(s):  
Plastic Deformation ◽  
High Pressure Torsion ◽  
Flow Behavior ◽  
Flow Characteristics ◽  
High Strength ◽  
Flow Properties ◽  
Angular Pressing ◽  
Ultrafine Grained ◽  
Small Grains ◽  
Ultrafine Grained Materials

Processing through the application of severe plastic deformation (SPD) leads to very significant grain refinement with grains that are typically in the submicrometer or even the nanometer range. These ultrafine-grained (UFG) materials provide an opportunity for achieving exceptional flow properties including high strength at ambient temperature and, if the very small grains are reasonably stable, superplastic elongations at high testing temperatures. These flow characteristics are examined for materials processed using the two SPD procedures of equal-channel angular pressing (ECAP) and high-pressure torsion (HPT).

Influence of Annealing on the Structure and Mechanical Properties of Ultrafine-Grained Alloy Ti-6Al-7Nb, Processed by Severe Plastic Deformation

2010 ◽  
Vol 667-669 ◽  
pp. 943-948 ◽  
Author(s):  
Veronika Polyakova ◽  
Irina P. Semenova ◽  
Ruslan Valiev
Keyword(s):  
Mechanical Properties ◽  
Plastic Deformation ◽  
Severe Plastic Deformation ◽  
Equal Channel Angular Pressing ◽  
Human Body ◽  
High Strength ◽  
Point Of View ◽  
Angular Pressing ◽  
Ultrafine Grained ◽  
Strength And Ductility

This work is devoted to enhancement of strength and ductility of the Ti-6Al-7Nb ELI alloy, which is less harmful from medical point of view for human body in comparison to Ti-6Al-4V. It has been demonstrated that formation of an ultrafine-grained structure in the alloy with the help of equal-channel angular pressing in combination with heat and deformation treatments allows reaching high strength (UTS = 1400 MPa) and sufficient ductility (elongation 10 %).

Investigations on Microstructure Evolution and Deformation Behavior of Aged and Ultrafine Grained Al-Zn-Mg Alloy Subjected to Severe Plastic Deformation

2010 ◽  
Vol 667-669 ◽  
pp. 253-258
Author(s):  
Wei Ping Hu ◽  
Si Yuan Zhang ◽  
Xiao Yu He ◽  
Zhen Yang Liu ◽  
Rolf Berghammer ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Mechanical Properties ◽  
Plastic Deformation ◽  
Grain Size ◽  
Severe Plastic Deformation ◽  
Microstructure Evolution ◽  
Deformation Behavior ◽  
Deformation Mechanisms ◽  
Mg Alloy ◽  
Ultrafine Grained

An aged Al-5Zn-1.6Mg alloy with fine η' precipitates was grain refined to ~100 nm grain size by severe plastic deformation (SPD). Microstructure evolution during SPD and mechanical behaviour after SPD of the alloy were characterized by electron microscopy and tensile, compression as well as nanoindentation tests. The influence of η' precipitates on microstructure and mechanical properties of ultrafine grained Al-Zn-Mg alloy is discussed with respect to their effect on dislocation configurations and deformation mechanisms during processing of the alloy.

MULTI-SCALE FINITE ELEMENT SIMULATION OF SEVERE PLASTIC DEFORMATION

2009 ◽  
Vol 23 (06n07) ◽  
pp. 1621-1626
Author(s):  
HYOUNG SEOP KIM
Keyword(s):  
Plastic Deformation ◽  
Finite Element ◽  
Severe Plastic Deformation ◽  
Constitutive Model ◽  
Dislocation Cell ◽  
Ultrafine Grain ◽  
Angular Pressing ◽  
Element Simulation ◽  
Ultrafine Grain Size ◽  
Ultrafine Grained

The technique of severe plastic deformation (SPD) enables one to produce metals and alloys with an ultrafine grain size of about 100 nm and less. As the mechanical properties of such ultrafine grained materials are governed by the plastic deformation during the SPD process, the understanding of the stress and strain development in a workpiece is very important for optimizing the SPD process design and for microstructural control. The objectives of this work is to present a constitutive model based on the dislocation density and dislocation cell evolution for large plastic strains as applied to equal channel angular pressing (ECAP). This paper briefly introduces the constitutive model and presents the results obtained with this model for ECAP by the finite element method.

Paradox of Strength and Ductility in Metals Processed Bysevere Plastic Deformation

2002 ◽  
Vol 17 (1) ◽  
pp. 5-8 ◽  
Author(s):  
R. Z. Valiev ◽  
I. V. Alexandrov ◽  
Y. T. Zhu ◽  
T. C. Lowe
Keyword(s):  
Mechanical Properties ◽  
Plastic Deformation ◽  
Grain Size ◽  
Yield Strength ◽  
Mechanical Behavior ◽  
High Strength ◽  
High Ductility ◽  
Elongation To Failure ◽  
Failure Ductility ◽  
Strength And Ductility

It is well known that plastic deformation induced by conventional forming methodssuch as rolling, drawing or extrusion can significantly increase the strength of metalsHowever, this increase is usually accompanied by a loss of ductility. For example, Fig.1 shows that with increasing plastic deformation, the yield strength of Cu and Almonotonically increases while their elongation to failure (ductility) decreases. Thesame trend is also true for other metals and alloys. Here we report an extraordinarycombination of high strength and high ductility produced in metals subject to severeplastic deformation (SPD). We believe that this unusual mechanical behavior is causedby the unique nanostructures generated by SPD processing. The combination ofultrafine grain size and high-density dislocations appears to enable deformation by newmechanisms. This work demonstrates the possibility of tailoring the microstructures ofmetals and alloys by SPD to obtain both high strength and high ductility. Materialswith such desirable mechanical properties are very attractive for advanced structuralapplications.

scholarly journals Hierarchical nanostructured aluminum alloy with ultrahigh strength and large plasticity

2019 ◽  
Vol 10 (1) ◽  
Author(s):  
Ge Wu ◽  
Chang Liu ◽  
Ligang Sun ◽  
Qing Wang ◽  
Baoan Sun ◽  
...  
Keyword(s):  
Plastic Deformation ◽  
Structural Design ◽  
Flow Behavior ◽  
High Strength ◽  
Al Alloy ◽  
High Ductility ◽  
Metallic Materials ◽  
Trade Off ◽  
Ultrahigh Strength ◽  
Continuous Generation

Abstract High strength and high ductility are often mutually exclusive properties for structural metallic materials. This is particularly important for aluminum (Al)-based alloys which are widely commercially employed. Here, we introduce a hierarchical nanostructured Al alloy with a structure of Al nanograins surrounded by nano-sized metallic glass (MG) shells. It achieves an ultrahigh yield strength of 1.2 GPa in tension (1.7 GPa in compression) along with 15% plasticity in tension (over 70% in compression). The nano-sized MG phase facilitates such ultrahigh strength by impeding dislocation gliding from one nanograin to another, while continuous generation-movement-annihilation of dislocations in the Al nanograins and the flow behavior of the nano-sized MG phase result in increased plasticity. This plastic deformation mechanism is also an efficient way to decrease grain size to sub-10 nm size for low melting temperature metals like Al, making this structural design one solution to the strength-plasticity trade-off.

Sign in / Sign up

Export Citation Format

Share Document