Microstructure and Mechanical Properties of FSWed Aluminum Extrusion with Bobbin Tools

2012 ◽  
Vol 706-709 ◽  
pp. 990-995 ◽  
Author(s):  
K. Okamoto ◽  
A. Sato ◽  
Seung Hwan C. Park ◽  
Satoshi Hirano
Keyword(s):  
Mechanical Properties ◽  
Feed Rate ◽  
Rotation Speed ◽  
Tool Design ◽  
Aluminum Extrusion ◽  
Tool Rotation Speed ◽  
Process Robustness ◽  
Tool Rotation ◽  
Process Productivity

Bobbin FSW technique is assessed in terms of process productivity and robustness considering the metallurgical and mechanical qualities of the joint. Several different designed bobbin tools were applied to aluminium A6xxx alloy extrusions, at feed rate of 400-1000mm/min with tool rotation speed of 600-1000rpm. In case of A6068-T6, a joint efficiency of 68% was achieved at 600mm/min, which is almost equivalent to the productivity and quality of the conventional FSWed joints, hence the potential of bobbin FSW technique was suggested. The bobbin tool design was further optimized considering the practical process robustness to the part fit issue, and defect free welds have been achieved for the joints with a set gap up to 1mm. However, the oxide remnant, so called “lazy S” was observed in a joint made with an inadequate designed tool, which significantly deteriorates the mechanical properties.

scholarly journals Effect of Tool Rotation Speed on Mechanical Properties and Microstructure as the Results of Friction Stir Welding Method on Aluminium 5083-7075

2016 ◽  
Vol 27 (1) ◽  
pp. 9-17
Author(s):  
Maryati Maryati ◽  
Bambang Soegijono ◽  
M Yudi Masduky ◽  
Tarmizi Tarmizi
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Friction Stir Welding ◽  
Rotation Speed ◽  
Incomplete Fusion ◽  
Connection Form ◽  
Friction Stir ◽  
Tool Rotation Speed ◽  
Speed Rotation ◽  
Tool Rotation

Friction Stir Welding (FSW) is a new method of welding process which is affordable and provide good quality. Aluminium 5083-7075 has been connected successfully by using friction stir welding (FSW) method into butt joint connection form. Tool rotation speed is one of the important parameters in FSW. The changes of rotation speed will affect the characteristics of mechanical properties and microstructure. The parameters of welding being used are welding speed of 29 mm/minutes by varying the speed rotation of 525 rpm, 680 rpm, 910 rpm, and 1555 rpm. In order to find out the mechanical strength of welds, tensile strength and hardness testing is done while finding out the microstructure will be done by using optical microscope and Scanning Electron Microscope (SEM). The result of the research showed that the highest tensile strength obtained at 910 rpm speed rotation about 244.85 MPa and the greatest hardness values was found on aluminium 5083 around the wheel zone area about 96 HV with rotary speed of 525 rpm. Then, the result of testing the macro and microstructure on all samples indicated defect which is seen as incomplete fusion and penetration causing the formation of onion rings. In other words, it is which showed that the result of stirring and tacking in the welding area is less than perfect.

Effect of welding parameters on mechanical properties and microstructure of friction stir welded brass joints

2018 ◽  
Vol 106 (6) ◽  
pp. 606 ◽  
Author(s):  
İnan Geçmen ◽  
Zarif Çatalgöl ◽  
Mustafa Kemal Bilici
Keyword(s):  
Mechanical Properties ◽  
Friction Stir Welding ◽  
Rotation Speed ◽  
Stir Zone ◽  
Weld Strength ◽  
Welding Parameters ◽  
Feed Speed ◽  
Friction Stir ◽  
Tool Rotation Speed ◽  
Tool Rotation

Friction stir welding is a method developed for the welding of high-alloy aluminum materials which are difficult to combine with conventional welding methods. Friction stir welding of MS 63 (brass) plates used different tools (tapered cylindrical, tapered threaded cylindrical), tool rotational speeds (1040, 1500, 2080 rpm) and traverse speeds (30,45,75,113 mm.min−1). Tensile, bending, radiography and microstructure tests were carried out to determine the mechanical properties of brass plates joined by friction stir welding technique. Microstructure characterization studies were based on optical microscope and SEM analysis techniques. In addition, after joining operations, radiographs were taken to see the internal structure failure. Brass sheets were successfully joined to the forehead in the macrostructure study. In the evaluation of the microstructure, it was determined that there were four regions of base metal, thermomechanically affected zone (TMEB), heat-affected zone (HAZ) and stir zone. In both welding tools, the weld strength increased with increasing tool rotation speed. The particles in the stir zone are reduced by increasing of the tool rotation speed. Given the strength and % elongation values, the highest weld strength was achieved with tapered pin tool with a tool rotation speed of 1040 rpm and a tool feed speed of 113 min−1.

Microstructure and Mechanical Properties of Friction Stir Welded Annealed Pure Copper Joints

2013 ◽  
Vol 787 ◽  
pp. 346-351
Author(s):  
Salar Salahi ◽  
Vahid Rezazadeh ◽  
Atabak Iranizad ◽  
Ali Hosseinzadeh ◽  
Amir Safari
Keyword(s):  
Mechanical Properties ◽  
Friction Stir Welding ◽  
Welding Speed ◽  
Heat Input ◽  
Applied Load ◽  
Rotation Speed ◽  
Pure Copper ◽  
Friction Stir ◽  
Tool Rotation Speed ◽  
Tool Rotation

As a novel technique for joining materials, friction stir welding (FSW) has significant advantages over the conventional welding methods and is widely applied for joining different materials including aluminum, magnesium and copper alloys. In this research, the mechanical and microstructural characteristics of friction stir welded annealed pure copper joints were investigated. The influence of the tool rotation speed, welding speed and applied load was studied. The friction stir welding (FSW) was conducted at welding speed ranged from 30 to 70 mm/ min, rotation speed ranged from 400 to 1200rpm and applied load ranged from 1000 to 1500 kg. After welding process, tensile and Vickers hardness tests were performed. It has been found that increasing the tool rotational speed and/or reducing the welding speed increases heat input and causes grain coarsening in stir zone. High applied load refines the microstructure of NZ and increases the hardness and tensile strength of NZ. An optimum heat input condition was found to reach the best mechanical properties of the joints. The tensile characteristics of the friction stir welded tensile samples depend significantly on the tool rotation speed ,welding speed and applied load.

Effect of Tool Rotation Speed and Feed Rate on Friction Stir Welding of 1100 Aluminum Alloy to Carbon Steel

2012 ◽  
Vol 445 ◽  
pp. 741-746 ◽  
Author(s):  
M. Habibnia ◽  
M. Shakeri ◽  
S. Nourouzi ◽  
Namdar Karimi
Keyword(s):  
Friction Stir Welding ◽  
Carbon Steel ◽  
Feed Rate ◽  
Rotation Speed ◽  
Butt Joint ◽  
Al Alloy ◽  
Dissimilar Metals ◽  
Friction Stir ◽  
Tool Rotation Speed ◽  
Tool Rotation

To achieve a defect-free butt joint of dissimilar metals by friction stir welding procedure, there are some major parameters, such as tool material and geometry, tool rotational speed, feed rate and tilt angel. This research is focused on dissimilar metals welding, namely 1100 Al alloy and 1045 carbon steel. In this paper, the effect of tool rotation speed and feed rate are experimentally investigated on surface appearance, microstructure and micro hardness of the friction stir welded plates. Optimum values of tool rotation speed and feed rate have been achieved experimentally by the quality of the butt joint.

Study the Role of Friction Stir Welding Tilt Angle on Microstructure and Hardness

2015 ◽  
Vol 799-800 ◽  
pp. 434-438 ◽  
Author(s):  
H.A.D. Hamid ◽  
A.A. Roslee
Keyword(s):  
Mechanical Properties ◽  
Friction Stir Welding ◽  
Tilt Angle ◽  
Welding Speed ◽  
Rotation Speed ◽  
Welding Parameters ◽  
Friction Stir ◽  
Tool Rotation Speed ◽  
Tool Pin ◽  
Tool Rotation

This paper presents an investigation of research objectives on the effect of tilt angle on microstructure and mechanical properties of dissimilar aluminum alloy sheets between AA5083 and AA6061, 5mm plates by using Friction Stir Welding (FSW) process in butt joint. The base materials of AA5083 and AA6061 were located on the retreating side (RS) and advancing side (AS), respectively. The welding process and the welding parameters such as tool pin profile, tool rotation speed, welding speed and tilt angle influenced the mechanical properties of the Friction Stir Welding joints significantly. For this experiment, the Friction Stir Welding materials joined under five different tilt angles (from 0oto 4o) with 86mm/min of welding speed and 910 rpm of tool rotation speed which were set similarly. Microscopic examination on the weld samples showed significant variation in the microstructure especially in the region of heat-affected zone (HAZ), weld nugget or dynamically recrystallized zone (DXZ) and in the base metal.

Influence of tool rotation speed and feed rate on the forming limit of friction stir welded AA6061-T6 sheets

2012 ◽  
Vol 227 (3) ◽  
pp. 520-541 ◽  
Author(s):  
Perumalla Janaki Ramulu ◽  
Satish V Kailas ◽  
R Ganesh Narayanan
Keyword(s):  
Strain Hardening ◽  
Feed Rate ◽  
Rotation Speed ◽  
Dome Height ◽  
Forming Limit ◽  
Welding Parameters ◽  
Strain Hardening Exponent ◽  
Friction Stir ◽  
Tool Rotation Speed ◽  
Tool Rotation

In this study, the influence of tool rotation speed and feed rate on the forming limit of friction stir welded Al 6061-T651 sheets has been investigated. The forming limit curve was evaluated by limit dome height test performed on all the friction stir welded sheets. The welding trials were conducted at a tool rotation speed of 1300 and 1400 r/min and feed rate of 90 and 100 mm/min. A third trial of welding was performed at a rotational speed of 1500 r/min and feed rate 120 mm/min. It is found that with increase in the tool rotation speed, from 1300 to 1400 r/min, for a constant feed rate, the forming limit of friction stir welded blank has improved and with increase in feed rate, from 90 to 100 mm/min, for a constant tool rotation speed, it has decreased. The forming limit of friction stir welded sheets is better than unwelded sheets. The thickness gradient after forming is severe in the cases of friction stir welded blanks made at higher feed rate and lower rotation speed. The strain hardening exponent of weld ( n) increases with increase in tool rotation speed and it decreases with increase in feed rate. It has been demonstrated that the change in the forming limit of friction stir welded sheets with respect to welding parameters is due to the thickness distribution severity and strain hardening exponent of the weld region during forming. There is not much variation in the dome height among the friction stir welded sheets tested. When compared with unwelded sheets, dome height of friction stir welded sheets is higher in near-plane-strain condition, but it is lesser in stretching strain paths.

Sign in / Sign up

Export Citation Format

Share Document