Cutting Performances of Coated PVD in High Speed End Milling of Aged Inconel 718

2013 ◽  
Vol 773-774 ◽  
pp. 653-660
Author(s):  
Mohd Shahir Kasim ◽  
Che Hassan Che Haron ◽  
Jaharah Abd Ghani ◽  
Juri Saedon ◽  
Mohd Amri Sulaiman
Keyword(s):  
Tool Life ◽  
Inconel 718 ◽  
High Speed ◽  
Cutting Tool ◽  
Elevated Temperatures ◽  
End Milling ◽  
Cutting Speed ◽  
Depth Of Cut ◽  
Radial Depth ◽  
Notch Wear

Inconel 718 is a material exhibiting characteristic that are able to maintain strength and integrity at elevated temperatures, but it is well known as a material with poor machinability. This paper presents a study of the performance in high speed machining of TiAlN/AlCrN nanomultilayer PVD coated Inconel 718 with minimum lubrication. Investigations have been made into the effects of cutting speed, feed rate and depth of cut (DOC) on the tool life. A toolmakers microscope and a scanning electron microscope (SEM) were used to examine the tool wear and chemical attrition, respectively, on the cutting tool during machining. In the machining of aged Inconel 718, the cutting tool experienced attrition, abrasion and notch wear throughout the experiment. Notch wear was found to be the dominant failure mode during milling; this wear appeared severe when localized flank wear reached the critical zone. The influence of radial depth despite the cutting speed, well known as having the most significant effect on tool life, is also discussed.

Effect of cutting parameters on tool life during end milling of AISI 4340 under MQL condition

2022 ◽  
Vol ahead-of-print (ahead-of-print) ◽  
Author(s):  
Ahsana Aqilah Ahmad ◽  
Jaharah A. Ghani ◽  
Che Hassan Che Haron
Keyword(s):  
Tool Wear ◽  
Tool Life ◽  
Wear Mechanism ◽  
High Speed ◽  
End Milling ◽  
Cutting Speed ◽  
Cutting Parameters ◽  
Depth Of Cut ◽  
Content Type ◽  
Radial Depth

Purpose The purpose of this paper is to study the cutting performance of high-speed regime end milling of AISI 4340 by investigating the tool life and wear mechanism of steel using the minimum quantity lubrication (MQL) technique to deliver the cutting fluid. Design/methodology/approach The experiments were designed using Taguchi L9 orthogonal array with the parameters chosen: cutting speed (between 300 and 400 m/min), feed rate (between 0.15 and 0.3 mm/tooth), axial depth of cut (between 0.5 and 0.7 mm) and radial depth of cut (between 0.3 and 0.7 mm). Toolmaker microscope, optical microscope and Hitachi SU3500 Variable Pressure Scanning Electron Microscope used to measure tool wear progression and wear mechanism. Findings Cutting speed 65.36%, radial depth of cut 24.06% and feed rate 6.28% are the cutting parameters that contribute the most to the rate of tool life. The study of the tool wear mechanism revealed that the oxide layer was observed during lower and high cutting speeds. The former provides a cushion of the protective layer while later reduce the surface hardness of the coated tool Originality/value A high-speed regime is usually carried out in dry conditions which can shorten the tool life and accelerate the tool wear. Thus, this research is important as it investigates how the use of MQL and cutting parameters can prolong the usage of tool life and at the same time to achieve a sustainable manufacturing process.

A Comprehensive Study on Surface Roughness in Machining of AISI D2 Hardened Steel

2012 ◽  
Vol 576 ◽  
pp. 60-63 ◽  
Author(s):  
N.A.H. Jasni ◽  
Mohd Amri Lajis
Keyword(s):  
Surface Roughness ◽  
High Speed ◽  
End Milling ◽  
Cutting Speed ◽  
Hardened Steel ◽  
Depth Of Cut ◽  
Feed Speed ◽  
Radial Depth ◽  
Aisi D2 ◽  
Coated Carbide

Hard milling of hardened steel has wide application in mould and die industries. However, milling induced surface finish has received little attention. An experimental investigation is conducted to comprehensively characterize the surface roughness of AISI D2 hardened steel (58-62 HRC) in end milling operation using TiAlN/AlCrN multilayer coated carbide. Surface roughness (Ra) was examined at different cutting speed (v) and radial depth of cut (dr) while the measurement was taken in feed speed, Vf and cutting speed, Vc directions. The experimental results show that the milled surface is anisotropic in nature. Surface roughness values in feed speed direction do not appear to correspond to any definite pattern in relation to cutting speed, while it increases with radial depth-of-cut within the range 0.13-0.24 µm. In cutting speed direction, surface roughness value decreases in the high speed range, while it increases in the high radial depth of cut. Radial depth of cut is the most influencing parameter in surface roughness followed by cutting speed.

Cutting Forces and Surface Roughness in High-Speed End Milling of Ti6Al4V

2013 ◽  
Vol 589-590 ◽  
pp. 76-81
Author(s):  
Fu Zeng Wang ◽  
Jun Zhao ◽  
An Hai Li ◽  
Jia Bang Zhao
Keyword(s):  
Surface Roughness ◽  
Surface Quality ◽  
Cutting Forces ◽  
High Speed ◽  
End Milling ◽  
Cutting Speed ◽  
Depth Of Cut ◽  
Wide Range ◽  
Radial Depth ◽  
Coated Carbide

In this paper, high speed milling experiments on Ti6Al4V were conducted with coated carbide inserts under a wide range of cutting conditions. The effects of cutting speed, feed rate and radial depth of cut on the cutting forces, chip morphologies as well as surface roughness were investigated. The results indicated that the cutting speed 200m/min could be considered as a critical value at which both relatively low cutting forces and good surface quality can be obtained at the same time. When the cutting speed exceeds 200m/min, the cutting forces increase rapidly and the surface quality degrades. There exist obvious correlations between cutting forces and surface roughness.

Tool life prediction by RSM for cryogenic milling of inconel 718

2019 ◽  
Vol ahead-of-print (ahead-of-print) ◽  
Author(s):  
Nurul Hayati Binti Abdul Halim ◽  
Che Hassan Che Haron ◽  
Jaharah A. Ghani ◽  
Muammar Faiq Azhar
Keyword(s):  
Tool Life ◽  
Inconel 718 ◽  
High Speed ◽  
Metal Cutting ◽  
Milling Process ◽  
Average Error ◽  
Depth Of Cut ◽  
Content Type ◽  
Radial Depth ◽  
Ball Nose Milling

Purpose The purpose of this study is to present the tool life optimization of carbide-coated ball nose milling inserts when high-speed milling of Inconel 718 under cryogenic CO2 condition. The main aims are to analyze the influence level of each cutting parameter on the tool life and to identify the optimum parameters that can lengthen the tool life to the maximum. Design/methodology/approach The experimental layout was designed using Box–Behnken RSM where all parameters were arranged without combining their highest and lowest values of each factor at the same time. A total of 29 milling experiments were conducted. Then, a statistical analysis using ANOVA was conducted to identify the relationship between the controlled factors on tool life. After that, a predictive model was developed to predict the variation of tool life within the predetermined parameters. Findings Results from the experimental found that the longest tool life of 22.77 min was achieved at Vc: 120 m/min, fz: 0.2 mm/tooth, ap: 0.5 mm and ae: 0.2 mm. ANOVA suggests the tool life of 23.4 min can be reached at Vc: 120.06 m/min, fz: 0.15 mm/tooth, ap: 0.66 mm and ae: 0.53 mm. All four controlled factors have influenced the tool life with the feed rate and radial depth of cut (DOC) as the major contributors. The developed mathematical model accurately represented the tool life at an average error of 8.2 per cent when compared to the actual and predicted tool life. Originality/value These experimental and statistical studies were conducted using Box–Behnken RSM method under cryogenic CO2 condition. It is a proven well-known method. However, the cooling method used in this study is a new technique and its effects on metal cutting, especially in the milling process of Inconel 718, has not yet been explored.

Prediction of Surface Roughness in High Speed Machining of Inconel 718

2011 ◽  
Vol 264-265 ◽  
pp. 1193-1198
Author(s):  
Mokhtar Suhaily ◽  
A.K.M. Nurul Amin ◽  
Anayet Ullah Patwari
Keyword(s):  
Surface Roughness ◽  
Surface Finish ◽  
Inconel 718 ◽  
High Speed ◽  
End Milling ◽  
Cutting Speed ◽  
Cutting Parameters ◽  
Machining Process ◽  
Depth Of Cut ◽  
High Speed Machining

Surface finish and dimensional accuracy is one of the most important requirements in machining process. Inconel 718 has been widely used in the aerospace industries. High speed machining (HSM) is capable of producing parts that require little or no grinding/lapping operations within the required machining tolerances. In this study small diameter tools are used to achieve high rpm to facilitate the application of low values of feed and depths of cut to investigate better surface finish in high speed machining of Inconel 718. This paper describes mathematically the effect of cutting parameters on Surface roughness in high speed end milling of Inconel 718. The mathematical model for the surface roughness has been developed in terms of cutting speed, feed rate, and axial depth of cut using design of experiments and the response surface methodology (RSM). Central composite design was employed in developing the surface roughness models in relation to primary cutting parameters. Machining were performed using CNC Vertical Machining Center (VMC) with a HES510 high speed machining attachment in which using a 4mm solid carbide fluted flat end mill tool. Wyko NT1100 optical profiler was used to measure the definite machined surface for obtaining the surface roughness data. The predicted results are in good agreement with the experimental one and hence the model can be efficiently used to predict the surface roughness value with in the specified cutting conditions limit.

Air Jet Assisted Machining of Inconel 718 with Whisker Reinforced Ceramic Tool

2013 ◽  
Vol 554-557 ◽  
pp. 2079-2084 ◽  
Author(s):  
Toshiyuki Obikawa ◽  
Kazuhiro Funai
Keyword(s):  
Tool Life ◽  
Inconel 718 ◽  
High Speed ◽  
Cutting Speed ◽  
Chemical Properties ◽  
High Speed Machining ◽  
Ceramic Tool ◽  
Air Jet ◽  
Hot Machining ◽  
Notch Wear

Nickel alloy is widely applied to aero-engines, marine structures, chemical plants, etc. This alloy has superior mechanical and chemical properties, but is one of difficult-to-machine materials because of its superior properties. For this reason, various machining methods, such as cryogenic machining, hot machining, machining using high pressure coolant and rotary machining have been studied for increasing the cutting speed and cutting efficiency of this alloy. Recently, a new lubrication method called air jet assisted (AJA) machining was developed to extend tool life by 20-30% in finish-turning of Inconel 718 and Ti-6Al-4V. In this machining method air jet as well as coolant was applied to the cutting area. In this study, AJA machining was applied to high speed machining of Inconel 718 with a SiC whisker reinforced ceramic tool. The air jet was applied from an air nozzle at the tool flank face. Because the ceramic tool is likely to suffer from severe notch wear, the influence of AJA machining on flank and notch wear of the ceramic tool was investigated experimentally. As a result, it was found that as compared to conventional wet machining, AJA machining increased flank wear but reduced notch wear, which is usually critical to the tool life of the reinforced ceramic tool. The tool wear characteristics peculiar to AJA machining were effective for extending tool life in high speed machining of this alloy.

Optimal Cutting Parameters for Desired Surface Roughness in End Milling Inconel 718

2010 ◽  
Vol 126-128 ◽  
pp. 911-916 ◽  
Author(s):  
Yuan Wei Wang ◽  
Song Zhang ◽  
Jian Feng Li ◽  
Tong Chao Ding
Keyword(s):  
Surface Roughness ◽  
Inconel 718 ◽  
End Milling ◽  
Cutting Speed ◽  
Cutting Parameters ◽  
Depth Of Cut ◽  
Radial Depth ◽  
Exponential Regression Model ◽  
Optimal Cutting Parameters ◽  
Coated Carbide

In this paper, Taguchi method was applied to design the cutting experiments when end milling Inconel 718 with the TiAlN-TiN coated carbide inserts. The signal-to-noise (S/N) ratio are employed to study the effects of cutting parameters (cutting speed, feed per tooth, radial depth of cut, and axial depth of cut) on surface roughness, and the optimal combination of the cutting parameters for the desired surface roughness is obtained. An exponential regression model for the surface roughness is formulated based on the experimental results. Finally, the verification tests show that surface roughness generated by the optimal cutting parameters is really the minimum value, and there is a good agreement between the predictive results and experimental measurements.

Experimental Studies on Cutting Temperature of Nickel-Based Supper Alloy Inconel 718

2013 ◽  
Vol 584 ◽  
pp. 20-23
Author(s):  
Mao Hua Xiao ◽  
Ning He ◽  
Liang Li ◽  
Xiu Qing Fu
Keyword(s):  
Inconel 718 ◽  
High Speed ◽  
Experimental Studies ◽  
Cutting Temperature ◽  
Cutting Speed ◽  
Cutting Parameters ◽  
Depth Of Cut ◽  
High Speed Milling ◽  
Radial Depth ◽  
The Impact

The method to measure the cutting speed when high speed milling nickel alloy Inconel 718 based on semi-artificial thermocouple. The cutting parameters, tool wear and so on the cutting temperature were analyzed. The tests showed that the temperature was gradually increased with the increase of cutting speed. The cutting speed must be more than 600m/min, when the ceramic tools would perform better cutting performance in the high-speed milling nickel-based superalloy. In order to achieve more efficient machining, milling speed can be increased to more than 1000m/min. The impact amount of Radial depth of cut and feed per tooth were relatively small.

Machinability Improvement by Workpiece Preheating during End Milling AISI H13 Hardened Steel

2011 ◽  
Vol 264-265 ◽  
pp. 888-893
Author(s):  
Mokhtar Suhaily ◽  
A.K.M. Nurul Amin ◽  
Anayet Ullah Patwari
Keyword(s):  
Surface Roughness ◽  
Surface Finish ◽  
Inconel 718 ◽  
High Speed ◽  
End Milling ◽  
Cutting Speed ◽  
Cutting Parameters ◽  
Machining Process ◽  
Depth Of Cut ◽  
High Speed Machining

Surface finish and dimensional accuracy is one of the most important requirements in machining process. Inconel 718 has been widely used in the aerospace industries. High speed machining (HSM) is capable of producing parts that require little or no grinding/lapping operations within the required machining tolerances. In this study small diameter tools are used to achieve high rpm to facilitate the application of low values of feed and depths of cut to investigate better surface finish in high speed machining of Inconel 718. This paper describes mathematically the effect of cutting parameters on Surface roughness in high speed end milling of Inconel 718. The mathematical model for the surface roughness has been developed in terms of cutting speed, feed rate, and axial depth of cut using design of experiments and the response surface methodology (RSM). Central composite design was employed in developing the surface roughness models in relation to primary cutting parameters. Machining were performed using CNC Vertical Machining Center (VMC) with a HES510 high speed machining attachment in which using a 4mm solid carbide fluted flat end mill tool. Wyko NT1100 optical profiler was used to measure the definite machined surface for obtaining the surface roughness data. The predicted results are in good agreement with the experimental one and hence the model can be efficiently used to predict the surface roughness value with in the specified cutting conditions limit.

Experimental Investigation on Tool Wear when End-Milling Inconel 718 with Coated Carbide Inserts

2011 ◽  
Vol 188 ◽  
pp. 410-415 ◽  
Author(s):  
Yuan Wei Wang ◽  
Jian Feng Li ◽  
Z.M. Li ◽  
Tong Chao Ding ◽  
Song Zhang
Keyword(s):  
Tool Wear ◽  
Inconel 718 ◽  
Flank Wear ◽  
End Milling ◽  
Cutting Speed ◽  
Cutting Parameters ◽  
Depth Of Cut ◽  
Radial Depth ◽  
Coated Carbide ◽  
Carbide Inserts

In this paper, some experiments were conducted to investigate tool wear when end-milling Inconel 718 with the TiAlN-TiN PVD coated carbide inserts. The worn tools were examined thoroughly under scanning electron microscope (SEM) with Energy Dispersive X-ray Spectroscopy and 3D digital microscope to expatiate tool wear morphologies and relevant mechanisms. The flank wear was uniformity in finishing milling process, and the average flank wear were selected as the criterion to study the effects of cutting parameters (cutting speed, feed per tooth, radial depth of cut, and axial depth of cut) on tool wear. Finally, the optimal combination of the cutting parameters for the desired tool life is obtained.

Sign in / Sign up

Export Citation Format

Share Document