Early-Stage Precipitation Phenomena and Composition-Dependent Hardening in Al-Mg-Si-(Cu) Alloys

2014 ◽  
Vol 794-796 ◽  
pp. 933-938 ◽  
Author(s):  
Vahid Fallah ◽  
Andreas Korinek ◽  
Babak Raeisinia ◽  
Mark Gallerneault ◽  
Shahrzad Esmaeili
Keyword(s):  
Electron Microscopy ◽  
Transmission Electron Microscopy ◽  
Early Stage ◽  
Scanning Calorimetry ◽  
Critical Knowledge ◽  
Transmission Electron ◽  
Final Microstructure ◽  
Precipitation Phenomena ◽  
Kinetics Of ◽  
Fcc Structure

Al-Mg-Si-(Cu), i.e. AA6xxx, alloys are widely used light alloys which can be effectively strengthened through precipitation hardening. The final microstructure, and thus properties, of these alloys after common artificial aging treatments are largely determined by the composition-dependent nano-scale clustering and precipitation that occur during the earliest stage of aging. Therefore, multi-length scale analysis of the earliest-stage of precipitation can provide critical knowledge in understanding the basis for the microstructural evolution during aging and attaining the desired microstructures and properties. Here, we investigate the effect of alloy composition on the evolution of early-stage clusters and precipitates during aging at 180°C using high resolution transmission electron microscopy. The results map a sequential evolution of clusters with an FCC structure but different morphology/orientation characteristics. GP-zones with structures other than FCC, also form in the early stages of aging. The composition-dependent kinetics of β” phase precipitation and hardening behavior are discussed in light of the results from differential scanning calorimetry experiments, microhardness measurements, and conventional transmission electron microscopy.

Crystallization of Al-Gd-La-Ni Metallic Glasses

1999 ◽  
Vol 580 ◽  
Author(s):  
T.K. Croat ◽  
A.K. Gangopadhyay ◽  
K.F. Kelton
Keyword(s):  
Electron Microscopy ◽  
Transmission Electron Microscopy ◽  
Metallic Glasses ◽  
Low Temperatures ◽  
Alloy Composition ◽  
Composition Range ◽  
Scanning Calorimetry ◽  
Crystallization Sequence ◽  
Transmission Electron ◽  
Kinetics Of

AbstractThe crystallization kinetics of Al-Gd-La-Ni metallic glasses to nanostructured phases are analyzed using differential scanning calorimetry and transmission electron microscopy. In a narrow alloy composition range near Al88Gd6La2Ni4, TEM reveals an amorphous phase separation that occurs upon annealing at low temperatures prior to crystallization. Al-enriched regions, typically 40 nm in diameter, bounded by rare-earth rich regions, are visible. Upon crystallization, α-Al forms preferentially at the interface between these phase separated regions. The relevance of this crystallization sequence to previous work in Al-RE-TM glasses and to the evolution of nanoscale microstructures common in the crystallization of other metallic glasses are discussed.

Atomic-scale structural and compositional analyses of Ruddlesden-Popper planar faults in AO-excess SrTiO3 (A = Sr2+, Ca2+, Ba2+) ceramics

2009 ◽  
Vol 24 (8) ◽  
pp. 2596-2604 ◽  
Author(s):  
Sašo Šturm ◽  
Makoto Shiojiri ◽  
Miran Čeh
Keyword(s):  
Electron Microscopy ◽  
Transmission Electron Microscopy ◽  
Dark Field ◽  
Atomic Scale ◽  
Transmission Electron ◽  
Initial Stage ◽  
Final Microstructure ◽  
Scanning Transmission ◽  
The Matrix ◽  
Annular Dark Field

The microstructure in AO-excess SrTiO3 (A = Sr2+, Ca2+, Ba2+) ceramics is strongly affected by the formation of Ruddlesden-Popper fault–rich (RP fault) lamellae, which are coherently intergrown with the matrix of the perovskite grains. We studied the structure and chemistry of RP faults by applying quantitative high-resolution transmission electron microscopy and high-angle annular dark-field scanning transmission electron microscopy analyses. We showed that the Sr2+ and Ca2+ dopant ions form RP faults during the initial stage of sintering. The final microstructure showed preferentially grown RP fault lamellae embedded in the central part of the anisotropic perovskite grains. In contrast, the dopant Ba2+ ions preferably substituted for Sr2+ in the SrTiO3 matrix by forming a BaxSr1−xTiO3 solid solution. The surplus of Sr2+ ions was compensated structurally in the later stages of sintering by the formation of SrO-rich RP faults. The resulting microstructure showed RP fault lamellae located at the surface of equiaxed BaxSr1-xTiO3 perovskite grains.

Growth kinetics of CoSi2 and Ge islands observed with in situ transmission electron microscopy

Micron ◽  
1999 ◽  
Vol 30 (1) ◽  
pp. 21-32 ◽  
Author(s):  
F.M. Ross ◽  
P.A. Bennett ◽  
R.M. Tromp ◽  
J. Tersoff ◽  
M. Reuter
Keyword(s):  
Electron Microscopy ◽  
Transmission Electron Microscopy ◽  
Growth Kinetics ◽  
Transmission Electron ◽  
Kinetics Of

Microstructures and Growth Characteristics of Self-Assembled InAs/GaAs Quantum Dots Investigated by Transmission Electron Microscopy

2007 ◽  
Vol 26-28 ◽  
pp. 1207-1210
Author(s):  
Hyung Seok Kim ◽  
Ju Hyung Suh ◽  
Chan Gyung Park ◽  
Sang Jun Lee ◽  
Sam Kyu Noh ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Transmission Electron Microscopy ◽  
Quantum Dots ◽  
Chemical Potential ◽  
Early Stage ◽  
Compressive Strain ◽  
Potential Gradient ◽  
Growth Direction ◽  
Transmission Electron ◽  
Self Assembled

The microstructure and strain characteristics of self-assembled InAs/GaAs quantum dots (QDs) were studied by using transmission electron microscopy. Compressive strain was induced to uncapped QDs from GaAs substrate and the misfit strain largely increased after the deposition of GaAs cap layer. Tensile strain outside QD was extended along the vertical growth direction; up to 15 nm above the wetting layer. Vertically nonaligned and aligned stacked QDs were grown by adjusting the thickness of GaAs spacer layers. The QDs with a lens-shaped morphology were formed in the early stage of growth, and their apex was flattened by the out-diffusion of In atoms upon GaAs capping. However, aligned QDs maintained their lens-shaped structure with round apex after capping. It is believed that their apex did not flatten because the chemical potential gradient of In was relatively low due to the adjacent InAs QD layers.

In-Situ Transmission Electron Microscopy and Computer Simulation Study of the Kinetics of Oxygen Loss in Yba2Cu3OZ

1989 ◽  
Vol 169 ◽  
Author(s):  
C. P. Burmester ◽  
L. T. Wille ◽  
R. Gronsky ◽  
B. T. Ahn ◽  
V. Y. Lee ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Transmission Electron Microscopy ◽  
High Resolution ◽  
Computer Simulation Study ◽  
Oxygen Loss ◽  
Domain Structures ◽  
Transmission Electron ◽  
Kinetics Of ◽  
Image Simulations

AbstractHigh resolution transmission electron microscopy during in‐situ quenching of YBa2Cu3Oz is used to study the kinetics of microdomain formation during oxygen loss in this system. Image simulations based on atomic models of oxygen‐vacancy order in the basal plane of this material generated by Monte Carlo calculations are used to interpret high resolution micrographs of the structures obtained by quenching. The observed domain structures agree well with those obtained from the simualtions.

Reactions in Metal-Metalloid Multilayers

1993 ◽  
Vol 311 ◽  
Author(s):  
Robert Sinclair ◽  
Toyohiko J. Konno
Keyword(s):  
Electron Microscopy ◽  
Transmission Electron Microscopy ◽  
Differential Scanning Calorimetry ◽  
Reactive Systems ◽  
Nucleation And Growth ◽  
In Situ Observation ◽  
Scanning Calorimetry ◽  
Compound Formation ◽  
Transmission Electron

ABSTRACTWe have studied the reactions at metal-metalloid interfaces using high resolution transmission electron microscopy, including in situ observation, and differential scanning calorimetry. There is contrasting behavior depending on the affinity for interaction or segregation. For reactive systems, compound formation ultimately results, but this can be preceded by solidstate amorphization. For non-reactive systems, crystallization of the metalloid is often achieved with nucleation and growth mediated by the metal phase.

Preparation and Property of Al87Ce3Ni8.5Mn1.5 Nanophase Amorphous Composites

2011 ◽  
Vol 412 ◽  
pp. 263-266
Author(s):  
Hong Wei Zhang ◽  
Li Li Zhang ◽  
Feng Rui Zhai ◽  
Jia Jin Tian ◽  
Can Bang Zhang
Keyword(s):  
Electron Microscopy ◽  
Transmission Electron Microscopy ◽  
Single Phase ◽  
Volume Fraction ◽  
Material Structure ◽  
X Ray Diffraction ◽  
Scanning Calorimetry ◽  
X Ray ◽  
Transmission Electron ◽  
Different Temperatures

The higher mechanical strength of Al87Ce3Ni8.5Mn1.5 nanophase amorphous composites has been obtained with two methods. The first nanophase amorphous composites are directly produced by the single roller spin quenching technology. The method taken for the second nanophase amorphous composites is at first to obtain amorphous single-phase alloy, followed by annealed at different temperatures .The formative condition, the microstructure, the particle size, the volume fraction of α-Al phase and microhardness of nanophase amorphous composites etc have been investigated and compared by X-ray diffraction (XRD) and transmission electron microscopy (TEM) and differential scanning calorimetry (DSC). The microstructure of composites produced by the second method is higher than the former, the fabricated material structure of the system is more uniform and the process is easier to control.

Sign in / Sign up

Export Citation Format

Share Document