Permittivities of Ultra-Low Dielectric Silica Beads and Aerogels

2015 ◽  
Vol 830-831 ◽  
pp. 444-447
Author(s):  
S. Nagapriya ◽  
B. Masin ◽  
H. Sreemoolanadhan ◽  
M.R. Ajith ◽  
Mariamma Mathew ◽  
...  
Keyword(s):  
High Speed ◽  
Ambient Pressure ◽  
Porous Silica ◽  
Silica Aerogels ◽  
Ambient Pressure Drying ◽  
Inorganic Materials ◽  
Silica Gels ◽  
Low Dielectric ◽  
Silica Beads ◽  
Lcr Meter

Materials with relative permittivity or dielectric constant near to that of air (εr~1) are known as ‘ultra-low k’ materials. They find a number of applications in inter-connects of micro-electronic circuits, antennae, high-speed communication substrates etc. Among the inorganic materials, porous silica is the widely studied candidate. Porous silica can be of many types depending upon the extent of porosity and size and connectivity of pores. This paper presents the details of measurement of permittivities and the results of silica beads and silica aerogels. Silica beads, prepared by microwave heating of silica gels, are spherical beads of average 1mm size. Hydrophobic silica aerogels, prepared by ambient pressure drying of silica gels, are irregular chunks of 5-10 mm size. Both are potential bulk fill insulation materials and hence the permittivity can be measured as an aggregate filling a definite volume. The permittivities of these have been measured upto 1 MHz by 3-terminal method using a precision LCR meter and a powder-paste cell as per ASTM-D150-11. The εr values of silica aerogels and silica beads in 20 Hz-1 MHz range could be measured and are less than 1.6 at 1 MHz.

Solvents Effects on Physicochemical Properties of Nano-Porous Silica Aerogels Prepared by Ambient Pressure Drying Method

2006 ◽  
Vol 510-511 ◽  
pp. 910-913 ◽  
Author(s):  
Seung Hun Lee ◽  
Eun A Lee ◽  
Hae Jin Hwang ◽  
Ji Woong Moon ◽  
In Sub Han ◽  
...  
Keyword(s):  
Ph Value ◽  
Ambient Pressure ◽  
Average Pore Size ◽  
Porous Silica ◽  
Sodium Silicate Solution ◽  
Silicate Solution ◽  
Silica Aerogels ◽  
Ambient Pressure Drying ◽  
Drying Method ◽  
Average Pore

Hydrophobic silica aerogels were synthesized by an ambient pressure drying method from silicic acid with a different pH value, which was prepared from sodium silicate solution (water glass). In this study we chose various hydrocarbon class solvents such as pentane, hexane, heptane, and toluene, and performed surface modification in TMCS (trimethylchlorosilane)/solvent solutions in order to improve reproducibility in aerogel production. Densities of the aerogels were about 0.1 ~ 0.3 g/cm3 , and apparent porosities were 88 ~ 96 %, depending on the processing conditions. Specific surface area was approximately 730 ~ 950 m2/g, and average pore size around 10 nm.

scholarly journals Silica Aerogel Monoliths Derived from Silica Hydrosol with Various Surfactants

Molecules ◽  
2018 ◽  
Vol 23 (12) ◽  
pp. 3192 ◽  
Author(s):  
Dong Chen ◽  
Xiaodong Wang ◽  
Wenhui Ding ◽  
Wenbing Zou ◽  
Qiong Zhu ◽  
...  
Keyword(s):  
Thermal Conductivity ◽  
Thermal Stability ◽  
Silica Aerogel ◽  
Low Cost ◽  
Ambient Pressure ◽  
Silica Aerogels ◽  
Ambient Pressure Drying ◽  
Low Thermal Conductivity ◽  
Silica Hydrosol ◽  
High Production Cost

Owing to their ultra-low thermal conductivity, silica aerogels are promising thermal insulators; however, their extensive application is limited by their high production cost. Thus, scientists have started to explore low-cost and easy preparation processes of silica aerogels. In this work, a low-cost method was proposed to prepare silica aerogels with industrial silica hydrosol and a subsequent ambient pressure drying (APD) process. Various surfactants (cationic, amphoteric, or anionic) were added to avoid solvent exchange and surface modification during the APD process. The effects of various surfactants on the microstructure, thermal conductivity, and thermal stability of the silica aerogels were studied. The results showed that the silica aerogels prepared with a cationic or anionic surfactant have better thermal stability than that prepared with an amphoteric surfactant. After being heated at 600 °C, the silica aerogel prepared with a cationic surfactant showed the highest specific surface area of 131 m2∙g−1 and the lowest thermal conductivity of 0.038 W∙m−1∙K−1. The obtained low-cost silica aerogel with low thermal conductivity could be widely applied as a thermal insulator for building and industrial energy-saving applications.

scholarly journals Eco-friendly approach for preparation of water-based superhydrophobic silica aerogels via ambient pressure drying

2021 ◽  
Vol 8 (1) ◽  
pp. 015021
Author(s):  
Xiaoling Yuan ◽  
Lihui Xu ◽  
Hong Pan ◽  
Yong Shen ◽  
Liming Wang ◽  
...  
Keyword(s):  
Ambient Pressure ◽  
Silica Aerogels ◽  
Ambient Pressure Drying ◽  
Water Based ◽  
Superhydrophobic Silica

Preparation of low-density porous silica thin films by ambient pressure drying

2004 ◽  
Author(s):  
Lanfang Yao ◽  
Jun Shen ◽  
Guangming Wu ◽  
Xingyuan Ni ◽  
Jue Wang ◽  
...  
Keyword(s):  
Thin Films ◽  
Ambient Pressure ◽  
Porous Silica ◽  
Ambient Pressure Drying ◽  
Low Density ◽  
Silica Thin Films

Cellulose nanofibril reinforced silica aerogels: optimization of the preparation process evaluated by a response surface methodology

RSC Advances ◽  
2016 ◽  
Vol 6 (102) ◽  
pp. 100326-100333 ◽  
Author(s):  
Jingjing Fu ◽  
Chunxia He ◽  
Jingda Huang ◽  
Zhilin Chen ◽  
Siqun Wang
Keyword(s):  
Mechanical Properties ◽  
Response Surface Methodology ◽  
Response Surface ◽  
Ambient Pressure ◽  
Silica Aerogels ◽  
Ambient Pressure Drying ◽  
Preparation Process ◽  
Cellulose Nanofibril ◽  
Drying Method ◽  
Composite Aerogels

CNF–silica composite aerogels with reinforced mechanical properties were prepared under an ambient pressure drying method and optimized by a response surface methodology.

Sign in / Sign up

Export Citation Format

Share Document