Corrosion Resistance of ZnAlMg Alloys for Batch Hot Dip Galvanizing

2016 ◽  
Vol 246 ◽  
pp. 99-104
Author(s):  
Mariola Saternus ◽  
Agnieszka Fornalczyk ◽  
Henryk Kania ◽  
Jacek Mendala
Keyword(s):  
Corrosion Resistance ◽  
Salt Spray ◽  
Comparative Methods ◽  
Corrosion Process ◽  
Neutral Salt ◽  
Zinc Bath ◽  
Moist Atmosphere ◽  
Corrosion Tests ◽  
Electrochemical Parameters ◽  
Resistance Tests

In the paper the results of corrosion resistance tests on ZnAlMg alloys used as batch hot dip galvanizing baths are presented. The tests were carried out on ZnAl alloys with 7 wt.% Al with the addition of 3 wt.% and 6 wt.% Mg. Corrosion resistance of tested alloys was compared with corrosion resistance of the traditional zinc bath alloy. Corrosion resistance of the alloys was defined by comparative methods in two standard corrosion tests in neutral salt spray and in moist atmosphere containing SO2. Electrochemical parameters of the corrosion process were determined on the basis of potentiodynamic tests. It was determined that the alloy of ZnAl7 has better corrosion resistance than the corrosion resistance of the alloy of a traditional zinc bath and that the addition of Mg to the alloy increases the corrosion resistance.

The Influence of the Chemical Composition of a Zinc Bath upon Corrosion Resistance of Coatings Obtained on Sebisty Steel

2016 ◽  
Vol 246 ◽  
pp. 85-90 ◽  
Author(s):  
Henryk Kania ◽  
Leszek Komorowski
Keyword(s):  
Corrosion Resistance ◽  
Chemical Composition ◽  
Coating Thickness ◽  
Corrosion Test ◽  
Salt Spray ◽  
Comparative Methods ◽  
Neutral Salt ◽  
Structural Components ◽  
Zinc Bath ◽  
Structure Of Coatings

In the paper the results of tests defining the influence of the chemical composition of a zinc bath on the corrosion resistance of coatings obtained on Sebisty steel are presented. The coatings for the tests were produced on Sebisty steel with the content of silicon of 0.18 wt. % in Zn-AlNi, Zn-AlNiPb and Zn-AlNiBiSn baths. Corrosion resistance of coatings obtained in alloy baths was compared with the corrosion resistance of a coating obtained in a bath of pure Zn. The structure of coatings has been developed, the chemical composition of structural components of the coating and the coating thickness have be established. Corrosion resistance of the coatings was defined by comparative methods in a standard corrosion test in neutral salt spray. The tests were carried out in accordance with the EN ISO 9227 standard. It has been established that alloy additions to a zinc bath have impact upon corrosion resistance of obtained coatings. The addition of Pb results in a decrease in corrosion resistance of a coating obtained on Sebisty steel.

Corrosion Resistance of Zn-31AlMg Coatings Obtained by Batch Hot Dip Method

2013 ◽  
Vol 212 ◽  
pp. 167-172 ◽  
Author(s):  
Henryk Kania ◽  
Marzena Bierońska
Keyword(s):  
Corrosion Resistance ◽  
Sulphur Dioxide ◽  
Salt Spray ◽  
Zinc Coating ◽  
Neutral Salt ◽  
Corrosion Tests ◽  
Good Corrosion Resistance ◽  
Zinc Coatings ◽  
Resistance Tests ◽  
Better Than

In the paper the authors present the results of corrosion resistance tests on coatings obtained in zinc-aluminium baths with the addition of Mg by use of the batch hot dip method. The content of Al in the bath was 31%, while the content of magnesium was 3 and 6%. In order to define corrosion resistance, two standard corrosion tests were performed in neutral salt spray and inmoist atmosphere containing sulphur dioxide. Corrosion resistance of tested pieces was compared with the corrosion resistance of a traditional zinc coating. It was established that Zn-31AlMg coatings have very good corrosion resistance in the tested environments, better than that of zinc coatings.

scholarly journals Impact of Bi and Sn on Microstructure and Corrosion Resistance of Zinc Coatings Obtained in Zn-AlNi Bath

Materials ◽  
2020 ◽  
Vol 13 (17) ◽  
pp. 3788
Author(s):  
Henryk Kania ◽  
Mariola Saternus ◽  
Jan Kudláček
Keyword(s):  
Corrosion Resistance ◽  
Salt Spray ◽  
Neutral Salt ◽  
Energy Dispersion Spectroscopy ◽  
Humid Atmosphere ◽  
Alloying Additions ◽  
Electrochemical Parameters ◽  
Zinc Coatings ◽  
Structural Research ◽  
The Impact

The paper presents results of studies on the impact of bismuth and tin additions to the Zn-AlNi bath on microstructure and corrosion resistance of hot dip galvanizig coatings. The structure at high magnifications on the top surface and cross-section of coatings received in the Zn-AlNiBiSn bath was revealed and the microanalysis EDS (energy dispersion spectroscopy) of chemical composition was determined. The corrosion resistance of the coatings was tested relatively in a neutral salt spray test (NSS), and tests in a humid atmosphere containing SO2. Electrochemical parameters of coatings corrosion were determined. It was found that Zn-AlNiBiSn coatings show lower corrosion resistance in comparison with the coatings received in the Zn-AlNi bath without Sn and Bi alloying additions. Structural research has shown the existence of precipitations of Sn-Bi alloy in the coating. It was found that Sn-Bi precipitations have more electropositive potential in relation to zinc, which promotes the formation of additional corrosion cells.

scholarly journals Structural Aspects of Decreasing the Corrosion Resistance of Zinc Coating Obtained in Baths with Al, Ni, and Pb Additives

Materials ◽  
2020 ◽  
Vol 13 (2) ◽  
pp. 385 ◽  
Author(s):  
Henryk Kania ◽  
Mariola Saternus ◽  
Jan Kudláček
Keyword(s):  
Corrosion Resistance ◽  
Salt Spray ◽  
Zinc Coating ◽  
Neutral Salt ◽  
Zinc Bath ◽  
Coating Structure ◽  
Humid Atmosphere ◽  
Pure Zinc ◽  
Si Content ◽  
Structural Aspects

The article presented the results of tests determining the synergistic effect of Al, Ni, and Pb additions on a zinc bath on the structure and corrosion resistance of coatings obtained on low silicon steel. Analyzed coatings were produced on S235JRG2 steel with Si content of 0.02 mass%. The corrosion resistance of the coatings was compared with the corrosion resistance of the coating obtained in the "pure" zinc bath. Structure at high magnifications (SEM) was determined, as well as coating thickness and chemical composition in microspheres. The corrosion resistance of the coatings was established comparatively in standard corrosion tests in neutral salt spray and a humid atmosphere containing SO2. It was found that the addition of Pb to the zinc bath reduced the corrosion resistance of the coatings. In the coating structure obtained in the Zn-AlNiPb bath, lead precipitation was observed in both the outer layer and the intermediate layer of the coating. Grain boundaries were the preferred site for lead precipitation. The presence of Pb precipitates favored conditions for the creation of additional corrosion cells, which led to a decrease in the corrosion resistance of the coatings.

scholarly journals Microstructure Characterization and Corrosion Resistance of Zinc Coating Obtained in a Zn-AlNiBi Galvanizing Bath

Coatings ◽  
2020 ◽  
Vol 10 (8) ◽  
pp. 758
Author(s):  
Henryk Kania ◽  
Mariola Saternus ◽  
Jan Kudláček ◽  
Jakub Svoboda
Keyword(s):  
Corrosion Resistance ◽  
Salt Spray ◽  
Zinc Coating ◽  
Corrosion Current ◽  
Neutral Salt ◽  
Zinc Bath ◽  
Electrochemical Test ◽  
Humid Atmosphere ◽  
Pure Zinc ◽  
The Impact

The article examines the impact of the addition of Al, Ni, and Bi to a zinc bath on the microstructure and corrosion resistance of hot dip galvanizing coatings. The microstructure on the surface and the cross-section of the coatings obtained in the Zn-AlNiBi bath were examined. The corrosion resistance of the coatings was assessed by the standard neutral salt spray test (EN ISO 9227), the sulfur dioxide test in a humid atmosphere (EN ISO 6988), and the electrochemical test. The corrosion resistance of Zn-AlNiBi coatings was compared with the corrosion resistance of coatings attained in the bath of “pure” zinc. The corrosion tests showed higher corrosion wear of the coating obtained in the Zn-AlNiBi bath and a higher value of the corrosion current density for this coating. It was found that the cause of the reduction of the corrosion resistance of the coating, in contrast to the coating obtained in the “pure” zinc bath, may be the presence of bismuth precipitates in the coating, which may form additional corrosion cells.

scholarly journals Accelerated Corrosion Tests in Quality Labels for Powder Coatings on Galvanized Steel—Comparison of Requirements and Experimental Evaluation

Materials ◽  
2021 ◽  
Vol 14 (21) ◽  
pp. 6547
Author(s):  
Izabela Kunce ◽  
Agnieszka Królikowska ◽  
Leszek Komorowski
Keyword(s):  
Corrosion Resistance ◽  
Corrosion Protection ◽  
Experimental Evaluation ◽  
Salt Spray ◽  
Galvanized Steel ◽  
Neutral Salt ◽  
Powder Coatings ◽  
Accelerated Corrosion ◽  
Corrosion Tests ◽  
Accelerated Corrosion Tests

Powder coatings are widely applied for corrosion protection of steel, aluminum, and hot dip galvanized steel in a variety of corrosive environments. Powder coatings are subjected to a number of strict laboratory tests to determine their mechanical properties, corrosion resistance, and color stability. Among European quality certificates for powder coatings applied to galvanized steel, the most commonly recognized are GSB-ST and Qualisteelcoat certificates, which also refer to the EN 13438 standard. Certificates of quality for powder coatings are constantly updated according to the latest research results and experience of specialists operating in the field of corrosion protection. This paper presents an experimental evaluation of how the required length of selected accelerated corrosion tests can affect the final assessment of powder coatings. On the example of two powder painting systems: polyester as well as based on epoxy and polyester resins, the paper presents the influence of the time of accelerated corrosion tests: ISO 6270, ISO 9227 (Neutral Salt Spray and Acetic Acid Salt Spray), and ISO 3231 on the protective properties of the coatings. The results of damage assessment according to ISO 4628 have been correlated with the requirements of particular quality specifications. Additionally, based on FTIR (Fourier Transform Infrared Spectroscopy) and EIS (Electrochemical Impedance Spectroscopy) analyses, the influence of the applied corrosion tests on the degradation degree of the coatings studied has been presented. The paper aims to present a tests for those powder coating systems applied to facilities for which the main requirement is corrosion resistance rather than aesthetics.

scholarly journals Design and Multidimensional Screening of Flash-PEO Coatings for Mg in Comparison to Commercial Chromium(VI) Conversion Coating

Metals ◽  
2021 ◽  
Vol 11 (2) ◽  
pp. 337
Author(s):  
Ewa Wierzbicka ◽  
Marta Mohedano ◽  
Endzhe Matykina ◽  
Raul Arrabal
Keyword(s):  
Corrosion Resistance ◽  
Corrosion Protection ◽  
Electrochemical Impedance ◽  
Salt Spray ◽  
Conversion Coating ◽  
Neutral Salt ◽  
Chromium Vi ◽  
Alkaline Electrolytes ◽  
Az31b Alloy ◽  
Plasma Electrolytic

REACH (Registration, Evaluation, Authorisation and Restriction of Chemicals) regulations demand for an expedient discovery of a Cr(VI)-free alternative corrosion protection for light alloys even though the green alternatives might never be as cheap as current harmful technologies. In the present work, flash- plasma electrolytic oxidation coatings (FPEO) with the process duration < 90 s are developed on AZ31B alloy in varied mixtures of silicate-, phosphate-, aluminate-, and fluoride-based alkaline electrolytes implementing current density and voltage limits. The overall evaluation of the coatings’ anticorrosion performance (electrochemical impedance spectroscopy (EIS), neutral salt spray test (NSST), paintability) shows that from nine optimized FPEO recipes, two (based on phosphate, fluoride, and aluminate or silicate mixtures) are found to be an adequate substitute for commercially used Cr(VI)-based conversion coating (CCC). The FPEO coatings with the best corrosion resistance consume a very low amount of energy (~1 kW h m−2 µm−1). It is also found that the lower the energy consumption of the FPEO process, the better the corrosion resistance of the resultant coating. The superb corrosion protection and a solid environmentally friendly outlook of PEO-based corrosion protection technology may facilitate the economic justification for industrial end-users of the current-consuming process as a replacement of the electroless CCC process.

Corrosion resistance of composite coating used for fastener protection

2019 ◽  
Vol 66 (5) ◽  
pp. 595-602
Author(s):  
Zhifeng Lin ◽  
Likun Xu ◽  
Xiangbo Li ◽  
Li Wang ◽  
Weimin Guo ◽  
...  
Keyword(s):  
Corrosion Resistance ◽  
Carbon Steel ◽  
Composite Coating ◽  
Marine Environment ◽  
Electrochemical Impedance ◽  
Salt Spray ◽  
Diffusion Method ◽  
Economic Losses ◽  
Neutral Salt ◽  
Content Type

Purpose The purpose of this paper is to examine the performance of a fastener composite coating system, sherardized (SD) coating/zinc-aluminum (ZA) coating whether it has good performance in marine environment. Design/methodology/approach In this paper, SD coating was fabricated on fastener surface by solid-diffusion method. ZA coating was fabricated by thermal sintering method. Corrosion behaviours of the composite coating were investigated with potentiodynamic polarization curves, open circuit potential and electrochemical impedance spectroscopy methods. Findings Neutral salt spray (NSS) and deep sea exposure tests revealed that the composite coating had excellent corrosion resistance. Polarization curve tests showed that corrosion current density of the sample with composite coating was significantly decreased, indicating an effective corrosion protection of the composite coating. OCP measurement of the sample in NaCl solution demonstrated that the composite coating had the best cathodic protection effect. The good corrosion resistance of the composite coating was obtained by the synergy of SD and ZA coating. Practical implications SD/ZA coating can be used in marine environment to prolong the life of carbon steel fastener. Social implications SD/ZA composite coating can reduce the risk and accident caused by failed fastener, avoid huge economic losses. Originality/value A new kind of composite coating was explored to protect the carbon steel fastener in marine environment. And the composite coating has the long-term anti-corrosion performance both in simulated and marine environment test.

Effect of Sol-Gel Film on the Corrosion Resistance of Low Carbon Steel Plate

2020 ◽  
Vol 984 ◽  
pp. 43-50
Author(s):  
Hua Yuan Zhang ◽  
Can Wang ◽  
Bing Xue ◽  
Jing Luo
Keyword(s):  
Corrosion Resistance ◽  
Carbon Steel ◽  
Steel Plate ◽  
Salt Spray ◽  
Sol Gel ◽  
Low Carbon Steel ◽  
Corrosion Current ◽  
Neutral Salt ◽  
Low Carbon ◽  
Gel Film

To improve the corrosion resistance on Q235 low carbon steel, in this paper, tetraethyl orthosilicate (TEOS), N-dodecyl trimethoxysilane and γ-(2,3-epoxypropoxy) propytrimethoxysilane (KH560) were used to make organic-inorganic hybrid sol-gel film. Cross cut test adhesion method, neutral salt spray test, electrochemical test and film protective efficiency were taken to value the corrosion resistance property. The corrosion topography was studied by optical microscope. In addition, potentiodynamic polarization, electrochemical impedance spectroscopy (EIS) curves and equivalent electric circuit fitting were used to analyze the corrosion mechanism. The cross cut adhesion of sol-gel film can reach 1 class and the protection class can attain 5 class after 72 hours neutral salt spray test. According to the potentiodynamic polarization curve analysis, the corrosion potential of sol-gel film coating sample after 0.5 hours immersion was -0.46 V (vs. SCE) on the 0.1 Hz, and its corrosion current density was 4.74×10-7 A·cm-2. The corrosion potential of bare Q235 low carbon steel plate after 0.5 hours immersion was -0.78 V (vs. SCE) on the 0.1 Hz, and its corrosion current density was 4.75×10-6 A·cm-2. The impedance value on 0.1 Hz (|Z|0.1Hz) (1.27×106 Ω·cm2) of sol-gel film coating sample was more than three orders of magnitude higher than the value of the low carbon steel plate. Even dipping in 3.5 wt. % NaCl for 72 hours, the |Z|0.1Hz value of sol-gel coating sample was still one order of magnitude higher than the low carbon steel plate with 0.5 hours immersion. Sol-gel film with excellent adhesion can significantly improve the corrosion resistance of low carbon steel plate. Sol-gel film can increase the protection efficiency of low carbon steel plate by 90%.

Sign in / Sign up

Export Citation Format

Share Document