Novel Design Approach to Create Deep Water Metallic Buoyancy Modules

2021 ◽  
Author(s):  
Vincent Loentgen ◽  
Nouhaila Maach ◽  
Yann Brouard ◽  
Julien Verdeil ◽  
Florian Germanetto ◽  
...  
Keyword(s):  
Boundary Conditions ◽  
Deep Water ◽  
Optimization Algorithm ◽  
Structural Integrity ◽  
Volume Fraction ◽  
Material Selection ◽  
Design Approach ◽  
Reconstruction Process ◽  
Buckling Stability ◽  
Novel Design

Abstract Buoyancy modules are widely used ancillary equipment aiming to shape riser systems to resist harsh offshore environments. Due to their thermoset polymeric nature, they are sensitive to the manufacturing parameters as well as subject to water absorption along their service life. To overcome the challenges of polymer-based buoyancy module, this paper explores the design of metallic buoyancy modules that can be 3-D metal printed. An initial material selection is performed to identify suitable material candidates for the optimization algorithm. Steel and aluminum materials are considered and evaluated on a representative case combining density, mechanical stress and buckling criterion. Then a topology optimization algorithm called ‘Adaptative Bone Mineralization’ is applied on the best candidate material, adapting their modulus of elasticity at each iteration according to the current stress distribution, load case definition and boundary conditions. The optimized design incorporates additional requirements related to additive manufacturing processes. Results of the optimization algorithm are presented in a progressive order of complexity starting from the optimization of an angular section of 11.25 degrees opening with symmetrical boundary conditions up to a quarter of half-shell buoyancy module fully optimized in 3D. The optimization process log, capturing the volume fraction and the maximum stress at each iteration, is presented and compared with the selected set of criteria. Impact of the manual reconstruction process of the buoyancy module is assessed and the buckling stability is evaluated as a post-treatment. Two-dimensional and three-dimensional topologically optimized buoyancy modules are presented and comply with the strict mass requirement, stress criterion and buckling stability achieving deep water depth. This novel design approach to create deep water metallic buoyancy modules achieves the tailoring of the buoyancy module's internal structure to maximize the buoyancy performance while ensuring its structural integrity.

A novel design approach to capture brake emissions in four wheelers

2020 ◽  
Author(s):  
Prakash Subramaniam ◽  
S. Sundaram ◽  
K. Gunasekaran ◽  
G. Vikas Reddy ◽  
Kaja Bantha Navas Raja Mohamed ◽  
...  
Keyword(s):  
Design Approach ◽  
Novel Design

Research on the application of 3D reconstruction technology in traditional handicraft design

2021 ◽  
pp. 002072092110052
Author(s):  
GuoLong Zhang
Keyword(s):  
Poisson Equation ◽  
Optimization Algorithm ◽  
Three Dimensional ◽  
Reconstruction Algorithm ◽  
Social Production ◽  
Design Constraint ◽  
Reconstruction Process ◽  
Key Steps ◽  
Shielding Design ◽  
Reconstruction Model

The use of computer technology for three-dimensional (3 D) reconstruction is one of the important development directions of social production. The purpose is to find a new method that can be used in traditional handicraft design, and to explore the application of 3 D reconstruction technology in it. Based on the description and analysis of 3 D reconstruction technology, the 3 D reconstruction algorithm based on Poisson equation is analyzed, and the key steps and problems of the method are clarified. Then, by introducing the shielding design constraint, a 3 D reconstruction algorithm based on shielded Poisson equation is proposed. Finally, the performance of two algorithms is compared by reconstructing the 3 D image of rabbit. The results show that: when the depth value of the algorithm is 11, the surface of the rabbit image obtained by the proposed optimization algorithm is smoother, and the details are more delicate and fluent; under different depth values, with the increase of the depth value, the number of vertices and faces of the two algorithms increase, and the optimal depth values of 3 D reconstruction are more than 8. However, the proposed optimization algorithm has more vertices, and performs better in the reconstruction process; the larger the depth value is, the more time and memory are consumed in 3 D reconstruction, so it is necessary to select the appropriate depth value; the shielding parameters of the algorithm have a great impact on the fineness of the reconstruction model. The larger the parameter is, the higher the fineness is. In a word, the proposed 3 D reconstruction algorithm based on shielded Poisson equation has better practicability and superiority.

scholarly journals A methodology for hygrothermal modelling of imperfect masonry interfaces

2021 ◽  
pp. 174425912198938
Author(s):  
Michael Gutland ◽  
Scott Bucking ◽  
Mario Santana Quintero
Keyword(s):  
Boundary Conditions ◽  
Material Properties ◽  
Structural Integrity ◽  
Bulk Material ◽  
Weather Conditions ◽  
Masonry Wall ◽  
Two Dimensional ◽  
Liquid Transport ◽  
Imperfect Contact ◽  
Moisture Contents

Hygrothermal models are important tools for assessing the risk of moisture-related decay mechanisms which can compromise structural integrity, loss of architectural features and material. There are several sources of uncertainty when modelling masonry, related to material properties, boundary conditions, quality of construction and two-dimensional interactions between mortar and unit. This paper examines the uncertainty at the mortar-unit interface with imperfections such as hairline cracks or imperfect contact conditions. These imperfections will alter the rate of liquid transport into and out of the wall and impede the liquid transport between mortar and masonry unit. This means that the effective liquid transport of the wall system will be different then if only properties of the bulk material were modelled. A detailed methodology for modelling this interface as a fracture is presented including definition of material properties for the fracture. The modelling methodology considers the combined effect of both the interface resistance across the mortar-unit interface and increase liquid transport in parallel to the interface, and is generalisable to various combinations of materials, geometries and fracture apertures. Two-dimensional DELPHIN models of a clay brick/cement-mortar masonry wall were created to simulate this interaction. The models were exposed to different boundary conditions to simulate wetting, drying and natural cyclic weather conditions. The results of these simulations were compared to a baseline model where the fracture model was not included. The presence of fractures increased the rate of absorption in the wetting phase and an increased rate of desorption in the drying phase. Under cyclic conditions, the result was higher peak moisture contents after rain events compared to baseline and lower moisture contents after long periods of drying. This demonstrated that detailed modelling of imperfections at the mortar-unit interface can have a definitive influence on results and conclusions from hygrothermal simulations.

scholarly journals Simulation of MASPn Experiments in MISTRA Test Facility with COCOSYS Code

2008 ◽  
Vol 2008 ◽  
pp. 1-7 ◽  
Author(s):  
Mantas Povilaitis ◽  
Egidijus Urbonavičius
Keyword(s):  
Boundary Conditions ◽  
Nuclear Power ◽  
Power Plants ◽  
Volume Fraction ◽  
Characteristic Length ◽  
Initial Conditions ◽  
Test Facility ◽  
Work Package ◽  
Acceptable Agreement

An issue of the stratified atmospheres in the containments of nuclear power plants is still unresolved; different experiments are performed in the test facilities like TOSQAN and MISTRA. MASPn experiments belong to the spray benchmark, initiated in the containment atmosphere mixing work package of the SARNET network. The benchmark consisted of MASP0, MASP1 and MASP2 experiments. Only the measured depressurisation rates during MASPn were available for the comparison with calculations. When the analysis was performed, the boundary conditions were not clearly defined therefore most of the attention was concentrated on MASP0 simulation in order to develop the nodalisation scheme and define the initial and boundary conditions. After achieving acceptable agreement with measured depressurisation rate, simulations of MASP1 and MASP2 experiments were performed to check the influence of sprays. The paper presents developed nodalisation scheme of MISTRA for the COCOSYS code and the results of analyses. In the performed analyses, several parameters were considered: initial conditions, loss coefficient of the junctions, initial gradients of temperature and steam volume fraction, and characteristic length of structures. Parametric analysis shows that in the simulation the heat losses through the external walls behind the lower condenser installed in the MISTRA facility determine the long-term depressurisation rate.

scholarly journals Tablet fragmentation without a disintegrant: A novel design approach for accelerating disintegration and drug release from 3D printed cellulosic tablets

2018 ◽  
Vol 118 ◽  
pp. 191-199 ◽  
Author(s):  
Basel Arafat ◽  
Magdalena Wojsz ◽  
Abdullah Isreb ◽  
Robert T. Forbes ◽  
Mohammad Isreb ◽  
...  
Keyword(s):  
Drug Release ◽  
Design Approach ◽  
3D Printed ◽  
Novel Design

Free vibration analysis of three-layer thin cylindrical shell with variable thickness two-dimensional FGM middle layer under arbitrary boundary conditions

2021 ◽  
pp. 109963622110204
Author(s):  
Xue-Yang Miao ◽  
Chao-Feng Li ◽  
Yu-Lin Jiang ◽  
Zi-Xuan Zhang
Keyword(s):  
Cylindrical Shell ◽  
Boundary Conditions ◽  
Volume Fraction ◽  
Ritz Method ◽  
Admissible Function ◽  
Free Vibration Analysis ◽  
Middle Layer ◽  
Two Dimensional ◽  
Arbitrary Boundary ◽  
Arbitrary Boundary Conditions

In this paper, a unified method is developed to analyze free vibrations of the three-layer functionally graded cylindrical shell with non-uniform thickness. The middle layer is composed of two-dimensional functionally gradient materials (2D-FGMs), whose thickness is set as a function of smooth continuity. Four sets of artificial springs are assigned at the ends of the shells to satisfy the arbitrary boundary conditions. The Sanders’ shell theory is used to obtain the strain and curvature-displacement relations. Furthermore, the Chebyshev polynomials are selected as the admissible function to improve computational efficiency, and the equation of motion is derived by the Rayleigh–Ritz method. The effects of spring stiffness, volume fraction indexes, configuration on of shell, and the change in thickness of the middle layer on the modal characteristics of the new structural shell are also analyzed.

Static Analysis of Moderately Thick Functionally Graded Plates With Various Boundary Conditions

2010 ◽  
Author(s):  
Nastaran Shahmansouri ◽  
Mohammad Mohammadi Aghdam ◽  
Kasra Bigdeli
Keyword(s):  
Boundary Conditions ◽  
Volume Fraction ◽  
Closed Form Solution ◽  
Shear Deformation Theory ◽  
Functionally Graded ◽  
Rectangular Plates ◽  
Functionally Graded Plates ◽  
Various Boundary Conditions ◽  
Fg Plates ◽  
Ode Systems

The present study investigates static analyses of moderately thick FG plates. Using the First Order Shear Deformation Theory (FSDT), functionally graded plates subjected to transversely distributed loading with various boundary conditions are studied. Effective mechanical properties which vary from one surface of the plate to the other assumed to be defined by a power law form of distribution. Different ceramic-metal sets of materials are studied. Solution of the governing equations, including five equilibrium and eight constitutive equations, is obtained by the Extended Kantorovich Method (EKM). The system of thirteen Partial Differential Equations (PDEs) in terms of displacements, rotations, force and moment resultants are considered as multiplications of separable function of independent variables x and y. Then by successful utilization of the EKM these equations are converted to a double set of ODE systems in terms of x and y. The obtained ODE systems are then solved iteratively until final convergence is achieved. Closed form solution is presented for these ODE sets. It is shown that the method is very stable and provides fast convergence and highly accurate predictions for both thin and moderately thick plates. Comparison of the normal stresses at various points of rectangular plates and deflection of mid-point of the plate are presented and compared with available data in the literature. The effects of the volume fraction exponent n on the behavior of the normalized deflection, moment resultants and stresses of FG plates are also studied. To validate data for analysis fully clamped FG plates, another analysis was carried out using finite element code ANSYS. Close agreement is observed between predictions of the EKM and ANSYS.

Thermo-Solutal Convection of a Nanofluid Utilizing Fourier’s-Type Compass Conditions

2020 ◽  
Vol 9 (4) ◽  
pp. 362-374
Author(s):  
J. C. Umavathi ◽  
Ali J. Chamkha
Keyword(s):  
Brownian Motion ◽  
Prandtl Number ◽  
Boundary Conditions ◽  
Volume Fraction ◽  
Temperature Fields ◽  
Physical Parameters ◽  
Surface Boundary ◽  
Perturbation Scheme ◽  
Runge Kutta ◽  
The Impact

Nanotechnology has infiltrated into duct design in parallel with many other fields of mechanical, medical and energy engineering. Motivated by the excellent potential of nanofluids, a subset of materials engineered at the nanoscale, in the present work, a new mathematical model is developed for natural convection in a vertical duct containing nanofluid. Numerical scrutiny for the double-diffusive free and forced convection within a duct encumbered with nanofluid is performed. Buongiorno’s model is deployed to define the nanofluid. Robin boundary conditions are used to define the surface boundary conditions. Thermal and concentration equations envisage the viscous, Brownian motion, thermosphores of the nanofluid, Soret and Dufour effects. Using the Boussi-nesq approximation the solutal buoyancy effect as a result of gradients in concentration are incorporated. The conservation equations which are nonlinear are numerically estimated using fourth order Runge-Kutta methodology and analytically ratifying regular perturbation scheme. The mass, heat, nanoparticle concentration and species concentration fields on eight dimensionless physical parameters such as thermal and mass Grashof numbers, Brownian motion parameter, thermal parameter, Prandtl number, Eckert number, Schmidt parameter, and Soret parameter are calculated. The impact of these parameters are outlined pictorially. The velocity and temperature fields are boosted with the thermal Grashof number. The Soret and the Schemidt parameters reduces the nanoparticle volume fraction but it heightens the momentum, temperature and concentration. At the cold wall thermal and concentration Grashof numbers reduces the Nusselt values but they increase the Nusselt values at the hot wall. The reversal consequence was attained at the hot plate. The perturbation and Runge-Kutta solutions are equal in the nonappearance of Prandtl number. The (E. Zanchini, Int. J. Heat Mass Transfer 41, 3949 (1998)). results are restored for the regular fluid. The heat transfer rate is high for nanofluid when matched with regular fluid.

Sign in / Sign up

Export Citation Format

Share Document