scholarly journals Analysis of Boron Removal for Reverse Osmosis, Ion Exchange, and Capacitive Deionization

2021 ◽  
Vol 43 (10) ◽  
pp. 654-663
Author(s):  
Yu Chang Kim ◽  
Sungil Lim ◽  
Bangwoo Han ◽  
Sang Bok Kim ◽  
Inyong Park ◽  
...  
Keyword(s):  
Energy Consumption ◽  
Ion Exchange ◽  
Reverse Osmosis ◽  
Ion Selectivity ◽  
Specific Energy Consumption ◽  
Operating Conditions ◽  
Feed Water ◽  
Carbon Electrode ◽  
Capacitive Deionization ◽  
Boron Removal

Objectives : This article provides a comparative analysis of boron removal for brackish water reverse osmosis (BWRO), boron selective ion exchange (IX), or capacitive deionization (CDI) processes. Permeate of 1st-Pass RO process has to be post-treated for additional boron removal. Hence, we experimentally analyzed the performance of boron removal and specific energy consumption (SEC) of three aforementioned processes and investigated whether the processes are suitable for 2nd pass process of RO desalination.Methods : Raw feed water was prepared using NaCl and B(OH)3. Semi-pilot scale RO and IX systems (over 1 m3/hr capacity) and bench scale CDI system (over 2.5 L/min) were tested for performance comparison. Boron concentration was measured using Azomethine-H method for feed and product water. Energy consumption was monitored by using power quality analyzer.Results and Discussion : Each process has its own operating conditions. The RO process required high pH of feed water for high boron removal rate, the IX process was operated below breakthrough point considering adsorption capacity of boron selective resin, and the CDI process didn’t remove boron because chloride ion has higher ion selectivity for carbon electrode than boron. In terms of SEC, the pressure-driven RO process showed the highest SEC among three processes. The CDI process based on electrical adsorption of carbon electrode showed a considerable energy consumption as well. On the other hand, the IX process was operated at low energy consumption because its removal is just based on adsorption-desorption mechanism.Conclusions : The RO and CDI processes have received a lot of attention as leading and emerging technology while the IX process was regarded as a stubborn process because of regeneration of resin and its several segmentalized steps. However, we found that the IX process has a better performance for boron removal and energy consumption.

scholarly journals Supercritical Carbon Dioxide Cycles for Concentrated Solar Power Plants: A Possible Alternative for Solar Desalination

Processes ◽  
2021 ◽  
Vol 10 (1) ◽  
pp. 72
Author(s):  
Rafael González-Almenara ◽  
Pablo Rodríguez de Arriba ◽  
Francesco Crespi ◽  
David Sánchez ◽  
Antonio Muñoz ◽  
...  
Keyword(s):  
Carbon Dioxide ◽  
Energy Consumption ◽  
Supercritical Carbon Dioxide ◽  
Reverse Osmosis ◽  
Solar Power ◽  
Specific Energy Consumption ◽  
Feed Water ◽  
Concentrated Solar Power ◽  
Solar Desalination ◽  
Supercritical Carbon

This manuscript investigates the supercritical carbon dioxide (sCO2) power cycle employed in the power block of concentrated solar power (CSP) plants—solar tower—as an alternative for solar desalination, developed with either distillation or reverse osmosis. This concept is investigated as a possible up-scaling of the SOLMIDEFF project, originally based on a hot-air micro gas turbine combined with a solar dish collector. For the upscaled concept, five different sCO2 cycles are considered, chosen amongst the best-performing configurations proposed in the literature for CSP applications, and modelled with Thermoflex software. The influence of ambient conditions is studied, considering two minimum cycle temperatures (35 °C and 50 °C), corresponding to Santa Cruz de Tenerife and Abu Dhabi, respectively. The results show that the low temperatures at the inlet of the heat rejection unit compromise the viability of distillation technologies. On the other hand, the high thermal efficiency achieved by these cycles, especially with the recompression and partial cooling layouts, reduces the specific energy consumption when combined with reverse osmosis (RO), below that of photovoltaic (PV)+RO. Feed-water preheating is explored as a solution to further reduce energy consumption, concluding that its actual interest is not clear and strongly depends on the location considered and the corresponding water quality standards.

scholarly journals Batch Reverse Osmosis Desalination Modeling under a Time-Dependent Pressure Profile

Membranes ◽  
2021 ◽  
Vol 11 (3) ◽  
pp. 173
Author(s):  
Abdeljalil Chougradi ◽  
François Zaviska ◽  
Ahmed Abed ◽  
Jérôme Harmand ◽  
Jamal-Eddine Jellal ◽  
...  
Keyword(s):  
Energy Consumption ◽  
Reverse Osmosis ◽  
Specific Energy ◽  
Energy Demand ◽  
Specific Energy Consumption ◽  
Pressure Profile ◽  
Recovery Ratio ◽  
Feed Concentration ◽  
Energetic Performance ◽  
Feed Volume

As world demand for clean water increases, reverse osmosis (RO) desalination has emerged as an attractive solution. Continuous RO is the most used desalination technology today. However, a new generation of configurations, working in unsteady-state feed concentration and pressure, have gained more attention recently, including the batch RO process. Our work presents a mathematical modeling for batch RO that offers the possibility of monitoring all variables of the process, including specific energy consumption, as a function of time and the recovery ratio. Validation is achieved by comparison with data from the experimental set-up and an existing model in the literature. Energetic comparison with continuous RO processes confirms that batch RO can be more energy efficient than can continuous RO, especially at a higher recovery ratio. It used, at recovery, 31% less energy for seawater and 19% less energy for brackish water. Modeling also proves that the batch RO process does not have to function under constant flux to deliver good energetic performance. In fact, under a linear pressure profile, batch RO can still deliver better energetic performance than can a continuous configuration. The parameters analysis shows that salinity, pump and energy recovery devices efficiencies are directly linked to the energy demand. While increasing feed volume has a limited effect after a certain volume due to dilution, it also shows, interestingly, a recovery ratio interval in which feed volume does not affect specific energy consumption.

scholarly journals Energetic and exergetic analysis of a convective drier: A case study of potato drying process

2020 ◽  
Vol 5 (1) ◽  
pp. 563-572
Author(s):  
Iman Golpour ◽  
Mohammad Kaveh ◽  
Reza Amiri Chayjan ◽  
Raquel P. F. Guiné
Keyword(s):  
Energy Consumption ◽  
Research Work ◽  
Specific Energy Consumption ◽  
Exergy Efficiency ◽  
Operating Conditions ◽  
Energy Utilization ◽  
Convective Drying ◽  
Drying Time ◽  
Energy And Exergy ◽  
Exergy Losses

AbstractThis research work focused on the evaluation of energy and exergy in the convective drying of potato slices. Experiments were conducted at four air temperatures (40, 50, 60 and 70°C) and three air velocities (0.5, 1.0 and 1.5 m/s) in a convective dryer, with circulating heated air. Freshly harvested potatoes with initial moisture content (MC) of 79.9% wet basis were used in this research. The influence of temperature and air velocity was investigated in terms of energy and exergy (energy utilization [EU], energy utilization ratio [EUR], exergy losses and exergy efficiency). The calculations for energy and exergy were based on the first and second laws of thermodynamics. Results indicated that EU, EUR and exergy losses decreased along drying time, while exergy efficiency increased. The specific energy consumption (SEC) varied from 1.94 × 105 to 3.14 × 105 kJ/kg. The exergy loss varied in the range of 0.006 to 0.036 kJ/s and the maximum exergy efficiency obtained was 85.85% at 70°C and 0.5 m/s, while minimum exergy efficiency was 57.07% at 40°C and 1.5 m/s. Moreover, the values of exergetic improvement potential (IP) rate changed between 0.0016 and 0.0046 kJ/s and the highest value occurred for drying at 70°C and 1.5 m/s, whereas the lowest value was for 70°C and 0.5 m/s. As a result, this knowledge will allow the optimization of convective dryers, when operating for the drying of this food product or others, as well as choosing the most appropriate operating conditions that cause the reduction of energy consumption, irreversibilities and losses in the industrial convective drying processes.

Conduction Roaster for Accelerated Roasting of Peanut

2021 ◽  
Vol 58 (02) ◽  
pp. 112-123
Author(s):  
Rakesh Kumar Raigar ◽  
Hari Niwas Mishra
Keyword(s):  
Energy Consumption ◽  
Specific Energy ◽  
Rotational Speed ◽  
Specific Energy Consumption ◽  
Quality Parameters ◽  
Operating Conditions ◽  
Moisture Loss ◽  
Optimum Operating ◽  
Small Scale ◽  
Roasting Temperature

Roasting is one of the thermo-mechanical operation in cereals and oilseeds processing. Low-capacity machine for mechanisation of roasting is necessary for small-scale processing. A conduction-type motorised rotary roaster (8 kg per batch) was designed and developed for roasting of peanuts. Performance of the roaster was evaluated in terms of moisture loss, scorched kernels, and specific energy consumption for accelerated roasting of peanut. The effects of different roasting conditions were studied to determine the optimum operating conditions of the roaster. Quality indices of peanuts as moisture loss (kg.kg-1), scorched kernel (%), and specific energy consumption (kWh.kg-1) were dependent on the operating conditions. The optimum value of moisture loss (0.041± 0.003 kg.kg-1), scorched kernel (0.93± 0.0.004 % ), and specific energy consumption (0.185 ± 0.005 kWh.kg-1) were obtained at roasting temperature of 170°C, roasting time of 15 min, and rotational speed of 20 rpm for roasting peanut. The roasting characteristics of peanut decreased linearly with increase in the temperature and time; and decrease in the rotational speed. The inferior quality parameters were observed at higher temperatures, speed and medium time of roasting. The study indicated optimum roasting temperature of peanut to be 170°C, and further increase in the process temperature had undesirable effects on roasted peanut quality due to high loss of moisture.

Membrane Distillation Desalination System With Gap Circulation and Cooling Using a Built-in Heat Exchanger

2020 ◽  
Vol 143 (1) ◽  
Author(s):  
Atia E. Khalifa
Keyword(s):  
Energy Consumption ◽  
Heat Exchanger ◽  
Specific Energy Consumption ◽  
Membrane Distillation ◽  
Operating Conditions ◽  
Water Desalination ◽  
Module Design ◽  
Membrane Surfaces ◽  
Best Value ◽  
Feed Temperature

Abstract A comprehensive experimental investigation is conducted to evaluate the performance of a new flux-enhanced compact water gap membrane distillation (WGMD) module design with gap circulation and cooling for water desalination. The new design uses a separate circulation loop to circulate the gap water, and a built-in heat exchanger coil implanted inside the coolant stream channel for cooling the circulated gap water. The WGMD modules with circulation and with circulation and cooling are compared with conventional WGMD without circulation. Variations of distillate flux, temperatures, and energy consumption are presented at different design operating conditions. Circulation and cooling of the gap water greatly enhance the output flux due to gap water motion and increase the temperature difference between membrane surfaces. However, the enhancement in flux was achieved at the expense of energy consumption. Circulation and cooling of gap water are more effective with bigger gap widths. Feed flowrate showed significant effects with gap water circulation and cooling. The electrical specific energy consumption (SEC) showed the best value of 7.9 and 8.8 kWh/m3 at a feed temperature of 70 °C for both conventional WGMD and WGMD with circulation modules, while the best value of SEC for the WGMD module with gap circulation and cooling was 9.4 kWh/m3 at a feed temperature of 80 °C.

Reverse Osmosis Technology for Wastewater Reuse

1991 ◽  
Vol 24 (9) ◽  
pp. 215-227 ◽  
Author(s):  
B. J. Mariñas
Keyword(s):  
Water Quality ◽  
Reverse Osmosis ◽  
Membrane Fouling ◽  
Quality Parameters ◽  
Operating Conditions ◽  
Water Quality Parameters ◽  
Feed Water ◽  
Hydraulic Pressure ◽  
Predominant Component ◽  
Percent Removal

Reverse osmosis technology has a great potential in the field of wastewater reclamation. A reverse osmosis plant includes the following processes: (1) feed water microfiltration and chemical conditioning, (2) membrane treatment, (3) permeate aeration, neutralization and disinfection, and (4) concentrate (liquid residue) treatment and disposal. The performance of reverse osmosis membranes depends on operating conditions and water quality parameters. Permeate productivity and contaminant removals increase with applied hydraulic pressure. Water quality parameters such as concentration, composition and pH also affect contaminant removal efficiencies. For example, the treatment of a simulated wastewater containing 10 mg/L of nitrate with a commercial polyamide-type reverse osmosis membrane resulted in membrane permeates containing approximately 0.05 mg/L of nitrate (or 99.5 percent removal) when sodium chloride was the major dissolved solid present in the feed water, and 1 mg/L (or 90 percent removal) when sodium sulfate was the predominant component. The removals of weak electrolyte contaminants are affected by feed water pH. For example, the removal of boron by a cellulose acetate-type membrane was reported to be greater than 99 percent at a pH of approximately 11, and less than 30 percent at a pH of 7. The practice of pre-treatment processes such as microfiltration and chemical conditioning can minimize performance deterioration resulting from membrane fouling by inorganic precipitates, organic macromolecules and microorganisms (biofouling).

Energy efficiency in membrane bioreactors

2013 ◽  
Vol 67 (12) ◽  
pp. 2685-2691 ◽  
Author(s):  
B. Barillon ◽  
S. Martin Ruel ◽  
C. Langlais ◽  
V. Lazarova
Keyword(s):  
Energy Consumption ◽  
Specific Energy Consumption ◽  
Hollow Fibre ◽  
Membrane Bioreactors ◽  
Operating Conditions ◽  
Key Factor ◽  
The Usa ◽  
Design Loads ◽  
Operation Parameters ◽  
Energy Audits

Energy consumption remains the key factor for the optimisation of the performance of membrane bioreactors (MBRs). This paper presents the results of the detailed energy audits of six full-scale MBRs operated by Suez Environnement in France, Spain and the USA based on on-site energy measurement and analysis of plant operation parameters and treatment performance. Specific energy consumption is compared for two different MBR configurations (flat sheet and hollow fibre membranes) and for plants with different design, loads and operation parameters. The aim of this project was to understand how the energy is consumed in MBR facilities and under which operating conditions, in order to finally provide guidelines and recommended practices for optimisation of MBR operation and design to reduce energy consumption and environmental impacts.

Sign in / Sign up

Export Citation Format

Share Document