scholarly journals Extracting Maximum Power from Wind Turbine Using Tip Speed Ratio and PO Algorithms by Limiting the Wind Speed

2021 ◽  
Vol 11 (4) ◽  
pp. 1241-1251
Author(s):  
Suja K
Keyword(s):  
Wind Speed ◽  
Wind Turbine ◽  
Maximum Power ◽  
Speed Ratio ◽  
Tip Speed Ratio

Experimental Study of Vertical Axis Wind Turbine with Wind Speed Self-Adapting

2012 ◽  
Vol 215-216 ◽  
pp. 1323-1326
Author(s):  
Ming Wei Xu ◽  
Jian Jun Qu ◽  
Han Zhang
Keyword(s):  
Wind Speed ◽  
Wind Turbine ◽  
Wind Velocity ◽  
Vertical Axis ◽  
Maximum Power ◽  
The Self ◽  
Power Coefficient ◽  
Speed Ratio ◽  
Vertical Axis Wind Turbine ◽  
Opening And Closing

A small vertical axis wind turbine with wind speed self-adapting was designed. The diameter and height of the turbine were both 0.7m. It featured that the blades were composed of movable and fixed blades, and the opening and closing of the movable blades realized the wind speed self-adapting. Aerodynamic performance of this new kind turbine was tested in a simple wind tunnel. Then the self-starting and power coefficient of the turbine were studied. The turbine with load could reliably self-start and operate stably even when the wind velocity was only 3.6 m/s. When the wind velocity was 8 m/s and the load torque was 0.1Nm, the movable blades no longer opened and the wind turbine realized the conversion from drag mode to lift mode. With the increase of wind speed, the maximum power coefficient of the turbine also improves gradually. Under 8 m/s wind speed, the maximum power coefficient of the turbine reaches to 12.26%. The experimental results showed that the new turbine not only improved the self-starting ability of the lift-style turbine, but also had a higher power coefficient in low tip speed ratio.

The Rotor Speed Control of 5MW Wind Turbine under Rated Wind Speed Using Adaptive-PID Controller

2012 ◽  
Vol 229-231 ◽  
pp. 2323-2326
Author(s):  
Zong Qi Tan ◽  
Can Can Li ◽  
Hui Jun Ye ◽  
Yu Qiong Zhou ◽  
Hua Ling Zhu
Keyword(s):  
Wind Speed ◽  
Wind Turbine ◽  
Pid Controller ◽  
Turbine Rotor ◽  
Speed Ratio ◽  
Rotor Speed ◽  
Rotating Speed ◽  
Tip Speed Ratio ◽  
Variable Wind ◽  
Wind Turbine Rotor

This paper designed the controller of the wind turbine rotor rotating speed. This model of adaptive-PID through control the tip-speed ratio and count the values of PID for variable wind speed. From the result of simulation, the wind speed can run in a good dynamic characteristic, and keep the rotor running in the best tip-speed ratio at the same time.

Study on Performance and Flow Condition of a Cross-Flow Wind Turbine With a Symmetrical Casing

2011 ◽  
Vol 133 (5) ◽  
Author(s):  
Junichiro Fukutomi ◽  
Toru Shigemitsu ◽  
Hiroki Daito
Keyword(s):  
Wind Turbine ◽  
Rotational Speed ◽  
Flow Condition ◽  
Cross Flow ◽  
Low Noise ◽  
Maximum Power ◽  
Power Coefficient ◽  
Speed Ratio ◽  
Tip Speed Ratio ◽  
The Cross

A cross-flow wind turbine has a high torque coefficient at a low tip speed ratio. Therefore, it is a good candidate for use as a self-starting turbine. Furthermore, it has low noise and excellent stability; therefore, it has attracted attention from the viewpoint of applications as a small wind turbine for an urban district. However, its maximum power coefficient is extremely low (10%) as compared to that of other small wind turbines. Prevailing winds in two directions often blow in urban and coastal regions. Therefore, in order to improve the performance and the flow condition of the cross-flow rotor, a casing suitable for this sort of prevailing wind conditions is designed in this research and the effect of the casing is investigated by experimental and numerical analysis. In the experiment, a wind tunnel with a square discharge is used and main flow velocity is set as 20 m/s. A torque meter, a rotational speed pickup, and a motor are assembled with the same axis as the test wind turbine and the tip speed ratio is changeable by a rotational speed controller. The casing is set around the cross-flow rotor and flow distribution at the rotor inlet and the outlet is measured by a one-hole pitot tube. The maximum power coefficient is obtained as Cpmax = 0.19 with the casing, however Cpmax = 0.098 without the casing. It is clear that the inlet and the outlet flow condition is improved by the casing. In the present paper, in order to improve the performance of a cross-flow wind turbine, a symmetrical casing suitable for prevailing winds in two directions is proposed. Then, the performance and the internal flow condition of the cross-flow wind turbine with the casing are clarified. Furthermore, the influence of the symmetrical casing on performance is discussed and the relation between the flow condition and performance is considered.

scholarly journals Maximizing the Output Power of Wind-Driven Grid-Connected Cage Induction Generator through Pole Control

2018 ◽  
Vol 29 (2) ◽  
pp. 39-49
Author(s):  
M. A. Abdel-Halim M. A. Abdel-Halim
Keyword(s):  
Wind Speed ◽  
Wind Turbine ◽  
Output Power ◽  
Amplitude Modulation ◽  
Electrical Power ◽  
Mechanical Power ◽  
Induction Generator ◽  
Speed Ratio ◽  
Tip Speed Ratio ◽  
Slip Ring

In this research, a cage induction generator has been linked to the grid and driven with a wind-turbine to generate electrical power. The cage generator has been used in place of the costly slip-ring generator. The performance characteristics of the cage induction generator have been ameliorated through changing its number of poles to comply with the level of the wind speed to maximize the mechanical power extracted from the wind. Pole changing has been achieved employing pole-amplitude modulation technique resulting in three sets of pole numbers. The results proved the feasibility and effectiveness of the suggested method, as the proposed technique led to driving the generator, and consequently the wind-turbine at speeds close or equal to those satisfying the optimum tip-speed ratio which corresponds to the point of maximum mechanical power.

Aerodynamic Performance Analysis of a Large Scale Wind Turbine Blade under Variable Condition

2013 ◽  
Vol 291-294 ◽  
pp. 527-530
Author(s):  
Peng Zhan Zhou ◽  
Fang Sheng Tan
Keyword(s):  
Wind Speed ◽  
Wind Turbine ◽  
Wind Power ◽  
Turbine Blade ◽  
Large Scale ◽  
Aerodynamic Performance ◽  
Power Coefficient ◽  
Speed Ratio ◽  
Tip Speed Ratio ◽  
Variable Condition

Based on BLADED software, the aerodynamic performance of a large scale wind turbine blade was analyzed under variable condition. The results show that the rated power of the blade under variable condition is increased 10%, when the rated wind speed is changed from 10.5m/s to 11.0 m/s. The blade’s wind power coefficient is above 0.46, and its tip speed ratio is between 7.8 and 11.4. When its tip speed ratio is 9.5, the blade’s maximum wind power coefficient is 0.486. It is indicated that the blade has good aerodynamic performance and wide scope of wind speed adaptive capacity. The blade root’s equivalent fatigue load is 2.11 MN•m, and its extreme flapwise load is 4.61 MN•m. The loads under variable condition are both less than that of the designed condition, so the blade’s application under variable condition is safe.

scholarly journals Performance of a Small-sized Savonious Blade with Wind Concentrator

2018 ◽  
Vol 10 (3) ◽  
pp. 1227
Author(s):  
Dygku. Asmanissa Awg. Osman ◽  
Norzanah Rosmin ◽  
Aede Hatib Mustaamal ◽  
Siti Maherah Hussin ◽  
Md Pauzi Abdullah
Keyword(s):  
Wind Speed ◽  
Wind Turbine ◽  
Experimental Testing ◽  
Electrical Power ◽  
Vertical Axis ◽  
Angular Speed ◽  
Speed Ratio ◽  
Vertical Axis Wind Turbine ◽  
Air Compressor ◽  
Tip Speed Ratio

<span>This paper presents the performance of a fabricated small-sized Savonious wind turbine with two blades. The design of Savonius vertical axis wind turbine (VAWT) was based on Malaysia wind speed condition. Meanwhile, the design of wind concentrator was based on the dimensions and the constant airflow of an air compressor. From the experimental testing in a laboratory, it was found that the proposed Savonious turbine has best performance when tested using wind concentrator. To conclude, airflow from air compressor can be increased when the proposed wind concentrator is used and hence increasing the proposed VAWT performance in terms of its angular speed (ω), tip speed ratio (TSR) and the generated electrical power (PE).</span>

scholarly journals Modeling and Analysis of Maximum Power Tracking of a 600 kW Hydraulic Energy Storage Wind Turbine Test Rig

Processes ◽  
2019 ◽  
Vol 7 (10) ◽  
pp. 706 ◽  
Author(s):  
Wei ◽  
Zhan ◽  
Liu ◽  
Tao ◽  
Yue
Keyword(s):  
Energy Storage ◽  
Wind Speed ◽  
Wind Turbine ◽  
Wind Power ◽  
Storage System ◽  
Energy Storage System ◽  
Maximum Power ◽  
Speed Ratio ◽  
Test Rig ◽  
Maximum Power Tracking

An innovative wind turbine with a particular hydraulic transmission and energy storage system is proposed in this paper. The purpose of applying the hydraulic transmission is to remove the gearbox and power converter of traditional wind turbine and cooperate on wind resource storing with the energy storage system. To overcome the volatility and intermittence shortcomings of wind and improve the output power quality, hydraulic accumulators are used as the energy storage device for wind energy regulation. The original gearbox and generator in the nacelle of a Micon 600 wind turbine were removed and replaced with a hydraulic pump to make a test rig for the investigation into maximum power point tracking (MPPT) of this hydraulic wind turbine concept. The mathematical model of the entire test system is established according to the four function modules. The MPPT control strategy based on the tip speed ratio (TSR) is adopted and a control system containing three closed-loop controls is designed to achieve maximum wind power extracting and produce constant frequency power generation. Ultimately, the dynamic response of rotor speed control is revealed under step change of wind speed and the maximum power tracking performance of the 600 kW hydraulic energy storage wind turbine test bench is simulated and analysed by subjecting to turbulent speed condition. The simulation results demonstrate that the rotor of the wind turbine can run at the expected optimal speed depending on wind speed, and the wind power utilization coefficient of the unit is stabilized at about the maximum value.

scholarly journals Experimental Study of Wind Booster Addition for Savonius Vertical Wind Turbine of Two Blades Variations Using Low Wind Speed

2019 ◽  
Vol 125 ◽  
pp. 14003
Author(s):  
Eflita Yohana ◽  
MSK. Tony Suryo U ◽  
Binawan Luhung ◽  
Mohamad Julian Reza ◽  
M Badruz Zaman
Keyword(s):  
Wind Speed ◽  
Wind Energy ◽  
Wind Turbine ◽  
Vertical Axis ◽  
Vertical Wind ◽  
Speed Ratio ◽  
Vertical Axis Wind Turbine ◽  
Tip Speed Ratio ◽  
Average Value ◽  
Low Wind Speed

The Wind turbine is a tool used in Wind Energy Conversion System (WECS). The wind turbine produces electricity by converting wind energy into kinetic energy and spinning to produce electricity. Vertical Axis Wind Turbine (VAWT) is designed to produce electricity from winds at low speeds. Vertical wind turbines have 2 types, they are wind turbine Savonius and Darrieus. This research is to know the effect of addition wind booster to Savonius vertical wind turbine with the variation 2 blades and 3 blades. Calculation the power generated by wind turbine using energy analysis method using the concept of the first law of thermodynamics. The result obtained is the highest value of blade power in Savonius wind turbine without wind booster (16.5 ± 1.9) W at wind speed 7 m/s with a tip speed ratio of 1.00 ± 0.01. While wind turbine Savonius with wind booster has the highest power (26.3 ± 1.6) W when the wind speed of 7 m/s with a tip speed ratio of 1.26 ± 0.01. The average value of vertical wind turbine power increases Savonius after wind booster use of 56%.

A Numerical Study on the Effects of Unsteady Wind on Vertical Axis Wind Turbine Performance

2013 ◽  
Author(s):  
Louis Angelo Danao ◽  
Jonathan Edwards ◽  
Okeoghene Eboibi ◽  
Robert Howell
Keyword(s):  
Wind Speed ◽  
Wind Turbine ◽  
Numerical Study ◽  
Angle Of Attack ◽  
Vertical Axis ◽  
Power Coefficient ◽  
Peak Performance ◽  
Speed Ratio ◽  
Vertical Axis Wind Turbine ◽  
Tip Speed Ratio

Numerical simulations using RANS–based CFD have been utilised to carry out investigations on the effects of unsteady wind in the performance of a wind tunnel vertical axis wind turbine. Using a validated CFD model, unsteady wind simulations revealed a fundamental relationship between instantaneous VAWT CP and wind speed. CFD data shows a CP variation in unsteady wind that cuts across the steady CP curve as wind speed fluctuates. A reference case with mean wind speed of 7m/s, wind speed amplitude of ±12%, fluctuating frequency of 0.5Hz and mean tip speed ratio of 4.4 has shown a wind cycle mean power coefficient of 0.33 that equals the steady wind maximum. Increasing wind speed causes the instantaneous tip speed ratio to fall which leads to higher effective angle of attack and deeper stalling on the blades. Stalled flow and rapid changes in angle of attack of the blade induce hysteresis loops in both lift and drag. Decreasing wind speeds limit the perceived angle of attack seen by the blades to near static stall thus reducing the positive effect of dynamic stall on lift generation. Three mean tip speed ratio cases were tested to study the effects of varying conditions of VAWT operation on the overall performance. As the mean tip speed ratio increases, the peak performance also increases.

Effects of Design Parameters on Aerodynamic Performance of New Profile Small Wind Turbine Blades

2015 ◽  
Author(s):  
Mahasidha Birajdar ◽  
Sandip Kale ◽  
S. N. Sapali
Keyword(s):  
Wind Speed ◽  
Wind Turbine ◽  
Turbine Blade ◽  
Rotational Speed ◽  
Aerodynamic Performance ◽  
Design Parameters ◽  
Speed Ratio ◽  
Tip Speed Ratio ◽  
Small Wind Turbine ◽  
Thrust And Torque

Wind is a one of the clean resources of energy and has the ability to contribute a considerable share in growing world energy consumption. The small wind turbine plays a vital role in fulfillment of energy needs preferably for household purpose. In order to unleash the budding of applicability of small wind turbine, it is necessary to improve its performance. The performance of a small wind turbine can be distinguished by the manners in which power, thrust and torque vary with the wind speed. The wind power indicates the amount of energy captured by the wind turbine rotor. It is convenient to express the performance of small wind turbine by means of non-dimensional performance curves, therefore in this paper the most graphs are drawn to power, thrust and torque coefficients as a function of the tip speed ratio. This paper presents the effect of design parameters such as the tip speed ratio, angle of attack, wind speed, solidity, number of blades, etc. on the aerodynamic performance of small wind turbine and proposes the optimum values of these parameters for the newly designed blade. The new designed blade consists of two new airfoils and named as IND 15045 and IND 09848. This new profile blade is designed for a wind turbine of 1 kW rated power. The blade is divided into ten sections. The designed length of blade is 1.5 m and it is made using IND 15045 airfoils at three root sections and IND 09848 airfoils for remaining seven sections. Q-Blade is used for the numerical simulation of wind turbine airfoils and blade. It is integrated tool of XFOIL and blade element momentum theory of wind turbine blade design. Also the effect of constant rotational speed operation, effect of stall regulation effect of rotational speed change and the effect of solidity on the performance of wind turbine is discussed. This paper delivers a broad view of perception for design of small wind turbine and parameter selection for the new wind turbine blade. Also in this paper the effect of different losses viz. tip losses, drag losses, stall losses and hub losses on the small wind turbine are discussed. The efficiency of the small wind turbine varies significantly with wind speed, but it would be designed such a way that maximized efficiencies are achieved at the wind speed where the maximum energy is available.

Sign in / Sign up

Export Citation Format

Share Document