Experimental Aerodynamic Characteristics of a Compound Wing in Ground Effect

2014 ◽  
Vol 136 (5) ◽  
Author(s):  
Saeed Jamei ◽  
Adi Maimun Abdul Malek ◽  
Shuhaimi Mansor ◽  
Nor Azwadi Che Sidik ◽  
Agoes Priyanto
Keyword(s):  
Reynolds Number ◽  
Drag Coefficient ◽  
Center Of Pressure ◽  
Lift Coefficient ◽  
Angle Of Attack ◽  
Leading Edge ◽  
Ground Effect ◽  
Reynolds Numbers ◽  
Aerodynamic Characteristics ◽  
Ground Clearance

Wing configuration is a parameter that affects the performance of wing-in-ground effect (WIG) craft. In this study, the aerodynamic characteristics of a new compound wing were investigated during ground effect. The compound wing was divided into three parts with a rectangular wing in the middle and two reverse taper wings with anhedral angle at the sides. The sectional profile of the wing model is NACA6409. The experiments on the compound wing and the rectangular wing were carried to examine different ground clearances, angles of attack, and Reynolds numbers. The aerodynamic coefficients of the compound wing were compared with those of the rectangular wing, which had an acceptable increase in its lift coefficient at small ground clearances, and its drag coefficient decreased compared to rectangular wing at a wide range of ground clearances, angles of attack, and Reynolds numbers. Furthermore, the lift to drag ratio of the compound wing improved considerably at small ground clearances. However, this improvement decreased at higher ground clearance. The drag polar of the compound wing showed the increment of lift coefficient versus drag coefficient was higher especially at small ground clearances. The Reynolds number had a gradual effect on lift and drag coefficients and also lift to drag of both wings. Generally, the nose down pitching moment of the compound wing was found smaller, but it was greater at high angle of attack and Reynolds number for all ground clearance. The center of pressure was closer to the leading edge of the wing in contrast to the rectangular wing. However, the center of pressure of the compound wing was later to the leading edge at high ground clearance, angle of attack, and Reynolds number.

Alula-Inspired Leading Edge Device for Low Reynolds Number Flight

2016 ◽  
Author(s):  
Boris A. Mandadzhiev ◽  
Michael K. Lynch ◽  
Leonardo P. Chamorro ◽  
Aimy A. Wissa
Keyword(s):  
Reynolds Number ◽  
Wind Tunnel ◽  
Drag Coefficient ◽  
Lift Coefficient ◽  
Angle Of Attack ◽  
Leading Edge ◽  
Aerodynamic Performance ◽  
Tip Vortex ◽  
Relative Angle ◽  
Lift And Drag

Robust and predictable aerodynamic performance of unmanned aerial vehicles at the limits of their design envelope is critical for safety and mission adaptability. In order for a fixed wing aircraft to maintain the lift necessary for sustained flight at very low speeds and large angles of attack (AoA), the wing shape has to change. This is often achieved by using deployable aerodynamic surfaces, such as flaps or slats, from the wing leading or trailing edges. In nature, one such device is a feathered structure on birds’ wings called the alula. The span of the alula is 5% to 20% of the wing and is attached to the first digit of the wing. The goal of the current study is to understand the aerodynamic effects of the alula on wing performance. A series of wind tunnel experiments are performed to quantify the effect of various alula deployment parameters on the aerodynamic performance of a cambered airfoil (S1223). A full wind tunnel span wing, with a single alula located at the wing mid-span is tested under uniform low-turbulence flow at three Reynolds numbers, Re = 85,000, 106,00 and 146,000. An experimental matrix is developed to find the range of effectiveness of an alula-type device. The alula relative angle of attack measured measured from the mean chord of the airfoil is varied to modulate tip-vortex strength, while the alula deflection is varied to modulate the distance of the tip vortex to the wing surface. Lift and drag forces were measured using a six axis force transducer. The lift and drag coefficients showed the greatest sensitivity to the the alula relative angle of attack, increasing the normalized lift coefficient by as much as 80%. Improvements in lift are strongly correlated to higher alula angle, with β = 0° – 5°, while reduction in the drag coefficient is observed with higher alula tip deflection ratios and lower β angles. Results show that, as the wing angle of attack and Reynolds number are increased, the overall lift co-efficient improvement is diminished while the reduction in drag coefficient is higher.

scholarly journals Lift and Drag Coefficient Map of NACA4415 Airfoil

2021 ◽  
Vol 2076 (1) ◽  
pp. 012066
Author(s):  
Rui Yin ◽  
Jing Huang ◽  
Zhi-Yuan He
Keyword(s):  
Reynolds Number ◽  
Drag Coefficient ◽  
Lift Coefficient ◽  
Angle Of Attack ◽  
Aerodynamic Characteristics ◽  
Optimal Angle ◽  
Fluent Software ◽  
Lift And Drag ◽  
Drag Ratio ◽  
Lift To Drag Ratio

Abstract The NACA4415 airfoil was numerically simulated with the help of the Fluent software to analyze its aerodynamic characteristics. Results are acquired as follows: The calculation accuracy of Fluent software is much higher than that of XFOIL software; the calculation result of SST k-ω(sstkw) turbulence model is closest to the experimental value; within a certain range, the larger the Reynolds number is, the larger the lift coefficient and lift-to-drag ratio of the airfoil will be, and the smaller the drag coefficient will be; when the angle of attack is less than the optimal angle of attack, the Reynolds number has less influence on the lift-to-drag coefficient and the lift-to-drag ratio; as the Reynolds number increases, the optimal angle of attack increases slightly, and the applicable angle of attack range for high lift-to-drag ratios becomes smaller.

scholarly journals Experimental study of low Reynolds number effects on aerodynamics of smooth and sinusoidal leading-edge wings in the vicinity of the ground

2021 ◽  
Vol 15 (2) ◽  
pp. 8205-8218
Author(s):  
A. A. Mehraban ◽  
Mohammad Hassan Djavareshkian
Keyword(s):  
Reynolds Number ◽  
Lift Coefficient ◽  
Leading Edge ◽  
Reynolds Numbers ◽  
Low Reynolds Numbers ◽  
Ground Clearance ◽  
Wide Range ◽  
Reynolds Number Effects ◽  
Low Reynolds ◽  
Stall Angle

Present study experimentally investigates the effects of ground clearance and Reynolds number on aerodynamic coefficients of smooth and sinusoidal leading-edge wings. Wind tunnel tests are conducted over a wide range of angles of attack from zero to 36 degrees, low Reynolds numbers of 30,000, 45,000 and 60,000, and also ground clearances of 0.5, 1 and ∞. Results showed that reduction of ground clearance and increment of Reynolds number cause the lift coefficient and the lift to drag ratio of both wings to be enhanced. Furthermore, the effects of Reynolds number and ground clearance on the smooth leading-edge wing are more than the sinusoidal leading-edge one. In addition, the sinusoidal leading-edge wing shows an excellent performance in the poststall region due to producing a higher lift and also by delaying the stall angle compared to the smooth leading-edge wing.

Experimental investigations of flow over NACA airfoils 0021 and 4412 of wind turbine blades with and without Tubercles

2021 ◽  
pp. 0309524X2110071
Author(s):  
Usman Butt ◽  
Shafqat Hussain ◽  
Stephan Schacht ◽  
Uwe Ritschel
Keyword(s):  
Wind Tunnel ◽  
Drag Coefficient ◽  
Wind Turbine ◽  
Critical Region ◽  
Lift Coefficient ◽  
Turbine Blades ◽  
Leading Edge ◽  
Reynolds Numbers ◽  
Experimental Investigations ◽  
Wind Turbine Blades

Experimental investigations of wind turbine blades having NACA airfoils 0021 and 4412 with and without tubercles on the leading edge have been performed in a wind tunnel. It was found that the lift coefficient of the airfoil 0021 with tubercles was higher at Re = 1.2×105 and 1.69×105 in post critical region (at higher angle of attach) than airfoils without tubercles but this difference relatively diminished at higher Reynolds numbers and beyond indicating that there is no effect on the lift coefficients of airfoils with tubercles at higher Reynolds numbers whereas drag coefficient remains unchanged. It is noted that at Re = 1.69×105, the lift coefficient of airfoil without tubercles drops from 0.96 to 0.42 as the angle of attack increases from 15° to 20° which is about 56% and the corresponding values of lift coefficient for airfoil with tubercles are 0.86 and 0.7 at respective angles with18% drop.

scholarly journals Aerodynamic and Vibration Characteristics of the Micro-Octocopter at Low Reynolds Number

2021 ◽  
Vol 2021 ◽  
pp. 1-9
Author(s):  
Xiaohua Zou ◽  
Mingsheng Ling ◽  
Wenzheng Zhai
Keyword(s):  
Reynolds Number ◽  
Load Capacity ◽  
Lift Coefficient ◽  
Angle Of Attack ◽  
Aerodynamic Characteristics ◽  
Vibration Characteristics ◽  
Low Reynolds ◽  
Vibration Performance ◽  
Drag Ratio ◽  
Lift To Drag Ratio

With the development of flight technology, the need for stable aerodynamic and vibration performance of the aircraft in the civil and military fields has gradually increased. In this case, the requirements for aerodynamic and vibration characteristics of the aircraft have also been strengthened. The existing four-rotor aircraft carries limited airborne equipment and payload, while the current eight-rotor aircraft adopts a plane layout. The size of the propeller is generally fixed, including the load capacity. The upper and lower tower layout analyzed in this paper can effectively solve the problems of insufficient four-axis load and unstable aerodynamic and vibration performance of the existing eight-axis aircraft. This paper takes the miniature octorotor as the research object and studies the aerodynamic characteristics of the miniature octorotor at different low Reynolds numbers, different air pressures and thicknesses, and the lift coefficient and lift-to-drag ratio, as well as the vibration under different elastic moduli and air pressure characteristics. The research algorithm adopted in this paper is the numerical method of fluid-solid cohesion and the control equation of flow field analysis. The research results show that, with the increase in the Reynolds number within a certain range, the aerodynamic characteristics of the miniature octorotor gradually become better. When the elastic modulus is 2.5 E, the aircraft’s specific performance is that the lift increases, the critical angle of attack increases, the drag decreases, the lift-to-drag ratio increases significantly, and the angle of attack decreases. However, the transition position of the flow around the airfoil surface is getting closer to the leading edge, and its state is more likely to transition from laminar flow to turbulent flow. When the unidirectional carbon fiber-reinforced thickness is 0.2 mm and the thin arc-shaped airfoil with the convex structure has a uniform thickness of 2.5% and a uniform curvature of 4.5%, the aerodynamic and vibration characteristics of the octorotor aircraft are most beneficial to flight.

Aerodynamic Characteristics of a Deformable Membrane Aerofoil

2014 ◽  
Vol 553 ◽  
pp. 255-260
Author(s):  
Viktor Šajn ◽  
Igor Petrović ◽  
Franc Kosel
Keyword(s):  
Experimental Study ◽  
Reynolds Number ◽  
Wind Tunnel ◽  
Lift Coefficient ◽  
Fluid Structure Interaction ◽  
Angle Of Attack ◽  
Aerodynamic Characteristics ◽  
Relative Difference ◽  
Structure Interaction ◽  
Deformable Membrane

In the paper, numerical and experimental study of low Reynolds number airflow around the deformable membrane airfoil (DMA) is presented. Simulations of a fluid-structure interaction between the fluid and the DMA were performed. In the experiment, the DMA model was made from a thin PVC sheet, which was wrapped around the steel rod at the leading and trailing edge. Measurements were performed in a wind tunnel at a chord Reynolds number of 85.7·103, over the angle of attack range from 0° to 15° and DMA shortening ratio from 0.025 to 0.150. Simulations were in an agreement with the experiment, since the average relative difference of coefficient of lift was smaller than 7.3%. For the same value of Reynolds number, DMA shows improved lift coefficient Cy= 2.18, compared to standard rigid airfoils.

scholarly journals Numerical Analysis of the Aerodynamic Characteristics of NACA-4312 Airfoil

2020 ◽  
Vol 01 (02) ◽  
pp. 29-36
Author(s):  
Md Rhyhanul Islam Pranto ◽  
Mohammad Ilias Inam
Keyword(s):  
Reynolds Number ◽  
Drag Coefficient ◽  
Lift Coefficient ◽  
Turbulence Models ◽  
Aerodynamic Characteristics ◽  
Numerical Results ◽  
Ansys Fluent ◽  
Coefficient Increase ◽  
Lift And Drag ◽  
Lift And Drag Coefficient

The aim of the work is to investigate the aerodynamic characteristics such as lift coefficient, drag coefficient, pressure distribution over a surface of an airfoil of NACA-4312. A commercial software ANSYS Fluent was used for these numerical simulations to calculate the aerodynamic characteristics of 2-D NACA-4312 airfoil at different angles of attack (α) at fixed Reynolds number (Re), equal to 5×10^5 . These simulations were solved using two different turbulence models, one was the Standard k-ε model with enhanced wall treatment and other was the SST k-ω model. Numerical results demonstrate that both models can produce similar results with little deviations. It was observed that both lift and drag coefficient increase at higher angles of attack, however lift coefficient starts to reduce at α =13° which is known as stalling condition. Numerical results also show that flow separations start at rare edge when the angle of attack is higher than 13° due to the reduction of lift coefficient.

scholarly journals Analysis on Flow Field Characteristics of Airfoil in Pitching Motion

2021 ◽  
Vol 2076 (1) ◽  
pp. 012069
Author(s):  
Rui Yin ◽  
Jing Huang ◽  
Zhi-Yuan He
Keyword(s):  
Flow Field ◽  
Drag Coefficient ◽  
Lift Coefficient ◽  
Angle Of Attack ◽  
Decisive Role ◽  
Aerodynamic Characteristics ◽  
Pitching Motion ◽  
Maximum Value ◽  
Flow Field Characteristics ◽  
Lift And Drag

Abstract Based on CFD, the flow field characteristics of NACA4412 airfoil are analyzed under pitching motion, and its aerodynamic characteristics are interpreted. The results show that streamline changes on the upper surface of the airfoil play a decisive role in the aerodynamic characteristics. The interaction between the vortex leads to fluctuations in the lift and drag coefficients. Under a big angle of attack, the secondary trailing vortex on the upper surface of the airfoil adheres to the trailing edge of the airfoil, resulting in an increased drag coefficient. Under a small angle of attack, the secondary trailing vortex can break away from the airfoil. The lift coefficient reaches the maximum value of 2.961 before the airfoil is turned upside down, and the drag coefficient reaches the maximum value of 1.515 after the airfoil is turned upside down, but the corresponding angles of attack of the two are equal.

Three-Dimensional Wing Design Towards the Future Mars Airplane

2011 ◽  
Author(s):  
Ryoji Kojima ◽  
Donghi Lee ◽  
Tomoaki Tatsukawa ◽  
Taku Nonomura ◽  
Akira Oyama ◽  
...  
Keyword(s):  
Reynolds Number ◽  
Aspect Ratio ◽  
Drag Coefficient ◽  
Lift Coefficient ◽  
Three Dimensional ◽  
Aerodynamic Characteristics ◽  
Viscous Drag ◽  
Stream Velocity ◽  
Main Stream ◽  
Lower Reynolds Number

The effects of aspect ratio and Reynolds number on aerodynamic characteristics of three-dimensional rectangular wing at low Reynolds number of 103 to 105, are investigated with Reynolds-averaged Navier-Stokes solver with the Baldwin-Lomax model. Present results show that lift coefficient decreases drastically at lower aspect ratio than 4. Besides, the much larger viscous drag coefficient is obtained at the lower Reynolds number, especially lower than 104. In order to focus on designing practical wings, the particular cases under the condition of fixed wing-surface area and fixed main stream velocity are conducted. The results show that there is trade-off between the decrease in viscous drag coefficient with increasing Reynolds number and the increase in lift coefficient with increasing aspect ratio. At the lower Reynolds number condition, as the former effect is stronger than the latter one, maximum lift-to-drag ratio is obtained at lower aspect ratio.

scholarly journals A Numerical Investigation of Co-flow Jet Effects on Airfoil Aerodynamic Characteristics

2021 ◽  
Author(s):  
Shima Yazdani ◽  
Erfan Salimipour ◽  
Ayoob Salimipour
Keyword(s):  
Reynolds Number ◽  
Stokes Equations ◽  
Active Flow Control ◽  
Lift Coefficient ◽  
Reynolds Numbers ◽  
Aerodynamic Characteristics ◽  
Dynamic Stall ◽  
Navier Stokes ◽  
Navier Stokes Equations ◽  
Momentum Coefficient

Abstract The present paper numerically investigates the performance of a Co-Flow Jet (CFJ) on the static and dynamic stall control of the NACA 0024 airfoil at Reynolds number 1.5 × 105. The two-dimensional Reynolds-averaged Navier-Stokes equations are solved using the SST k-ω turbulence model. The results show that the lift coefficients at the low angles of attack (up to α = 15̊) are significantly increased at Cµ = 0.06, however for the higher momentum coefficients, it is not seen an improvement in the aerodynamic characteristics. Also, the dynamic stall for a range of α between 0̊ and 20̊ at the mentioned Reynolds number and with the reduced frequency of 0.15 for two CFJ cases with Cµ = 0.05 and 0.07 are investigated. For the case with Cµ = 0.07, the lift coefficient curve did not present a noticeable stall feature compared to Cµ = 0.05. The effect of this active flow control by increasing the Reynolds numbers from 0.5 × 105 to 3 × 105 is also investigated. At all studied Reynolds numbers, the lift coefficient enhances as the momentum coefficient increases where its best performance is obtained at the angle of attack α = 15̊.

Sign in / Sign up

Export Citation Format

Share Document