scholarly journals Understanding balloon-borne frost point hygrometer measurements after contamination by mixed-phase clouds

2021 ◽  
Vol 14 (1) ◽  
pp. 239-268
Author(s):  
Teresa Jorge ◽  
Simone Brunamonti ◽  
Yann Poltera ◽  
Frank G. Wienhold ◽  
Bei P. Luo ◽  
...  
Keyword(s):  
Water Vapour ◽  
High Water ◽  
Large Set ◽  
Mixing Ratios ◽  
Frost Point ◽  
Depth Analysis ◽  
Air Chemistry ◽  
Computational Fluid Dynamics Cfd ◽  
Impact Angles ◽  
Mixed Phase Clouds

Abstract. Balloon-borne water vapour measurements in the upper troposphere and lower stratosphere (UTLS) by means of frost point hygrometers provide important information on air chemistry and climate. However, the risk of contamination from sublimating hydrometeors collected by the intake tube may render these measurements unusable, particularly after crossing low clouds containing supercooled droplets. A large set of (sub)tropical measurements during the 2016–2017 StratoClim balloon campaigns at the southern slopes of the Himalayas allows us to perform an in-depth analysis of this type of contamination. We investigate the efficiency of wall contact and freezing of supercooled droplets in the intake tube and the subsequent sublimation in the UTLS using computational fluid dynamics (CFD). We find that the airflow can enter the intake tube with impact angles up to 60∘, owing to the pendulum motion of the payload. Supercooled droplets with radii > 70 µm, as they frequently occur in mid-tropospheric clouds, typically undergo contact freezing when entering the intake tube, whereas only about 50 % of droplets with 10 µm radius freeze, and droplets < 5 µm radius mostly avoid contact. According to CFD, sublimation of water from an icy intake can account for the occasionally observed unrealistically high water vapour mixing ratios (χH2O > 100 ppmv) in the stratosphere. Furthermore, we use CFD to differentiate between stratospheric water vapour contamination by an icy intake tube and contamination caused by outgassing from the balloon and payload, revealing that the latter starts playing a role only during ascent at high altitudes (p < 20 hPa).

scholarly journals Understanding cryogenic frost point hygrometer measurements after contamination by mixed-phase clouds

2020 ◽  
Author(s):  
Teresa Jorge ◽  
Simone Brunamonti ◽  
Yann Poltera ◽  
Frank G. Wienhold ◽  
Bei P. Luo ◽  
...  
Keyword(s):  
Water Vapour ◽  
Large Set ◽  
Pendulum Motion ◽  
Upper Troposphere ◽  
Frost Point ◽  
Depth Analysis ◽  
Air Chemistry ◽  
Computational Fluid Dynamics Cfd ◽  
Mixed Phase Clouds ◽  
Stratospheric Water Vapour

Abstract. Balloon-borne water vapour measurements in the (sub)tropical upper troposphere and lower stratosphere (UTLS) by means of frost point hygrometers provide important information on air chemistry and climate. However, the risk of contamination from sublimating hydrometeors collected by the intake tube may render these measurements difficult, particularly after crossing low clouds containing supercooled droplets. A large set of measurements during the 2016–2017 StratoClim balloon campaigns at the southern slopes of the Himalayas allows us to perform an in-depth analysis of this type of contamination. We investigate the efficiency of wall-contact and freezing of supercooled droplets in the intake tube and the subsequent sublimation in the UTLS using Computational Fluid Dynamics (CFD). We find that the airflow can enter the intake tube with impingement angles up to 60°, owing to the pendulum motion of the payload. Supercooled droplets with radii > 70 μm, as they frequently occur in mid-tropospheric clouds, typically undergo contact freezing when entering the intake tube, whereas only about 50 % of droplets with 10 μm radius freeze, and droplets  100 ppmv) in the stratosphere. Furthermore, we use CFD to differentiate between stratospheric water vapour contamination by an icy intake tube and contamination caused by outgassing from the balloon and payload, revealing that the latter starts playing a role only at high altitudes (p 

scholarly journals Laboratory evaluation of the effect of nitric acid uptake on frost point hygrometer performance

2011 ◽  
Vol 4 (2) ◽  
pp. 289-296 ◽  
Author(s):  
T. Thornberry ◽  
T. Gierczak ◽  
R. S. Gao ◽  
H. Vömel ◽  
L. A. Watts ◽  
...  
Keyword(s):  
Nitric Acid ◽  
Surface Area ◽  
Water Vapour ◽  
Lower Stratosphere ◽  
Laboratory Evaluation ◽  
Acid Uptake ◽  
Reliable Determination ◽  
Point Temperature ◽  
Mixing Ratios ◽  
Frost Point

Abstract. Chilled mirror hygrometers (CMH) are widely used to measure water vapour in the troposphere and lower stratosphere from balloon-borne sondes. Systematic discrepancies among in situ water vapour instruments have been observed at low water vapour mixing ratios (<5 ppm) in the upper troposphere and lower stratosphere (UT/LS). Understanding the source of the measurement discrepancies is important for a more accurate and reliable determination of water vapour abundance in this region. We have conducted a laboratory study to investigate the potential interference of gas-phase nitric acid (HNO3) with the measurement of frost point temperature, and consequently the water vapour mixing ratio, determined by CMH under conditions representative of operation in the UT/LS. No detectable interference in the measured frost point temperature was found for HNO3 mixing ratios of up to 4 ppb for exposure times up to 150 min. HNO3 was observed to co-condense on the mirror frost, with the adsorbed mass increasing linearly with time at constant exposure levels. Over the duration of a typical balloon sonde ascent (90–120 min), the maximum accumulated HNO3 amounts were comparable to monolayer coverage of the geometric mirror surface area, which corresponds to only a small fraction of the actual frost layer surface area. This small amount of co-condensed HNO3 is consistent with the observed lack of HNO3 interference in the frost point measurement because the CMH utilizes significant reductions (>10%) in surface reflectivity by the condensate to determine H2O.

scholarly journals Laboratory evaluation of the effect of nitric acid uptake on frost point hygrometer performance

2010 ◽  
Vol 3 (4) ◽  
pp. 3725-3745
Author(s):  
T. Thornberry ◽  
T. Gierczak ◽  
R. S. Gao ◽  
H. Vömel ◽  
L. A. Watts ◽  
...  
Keyword(s):  
Nitric Acid ◽  
Surface Area ◽  
Water Vapour ◽  
Lower Stratosphere ◽  
Laboratory Evaluation ◽  
Acid Uptake ◽  
Reliable Determination ◽  
Point Temperature ◽  
Mixing Ratios ◽  
Frost Point

Abstract. Chilled mirror hygrometers (CMH) are widely used to measure water vapour in the troposphere and lower stratosphere from balloon-borne sondes. Systematic discrepancies among in situ water vapour instruments have been observed at low water vapour mixing ratios (<5 ppm) in the upper troposphere and lower stratosphere (UT/LS). Understanding the source of the measurement discrepancies is important for a more accurate and reliable determination of water vapour abundance in this region. We have conducted a laboratory study to investigate the potential interference of gas-phase nitric acid (HNO3) with the measurement of frost point temperature, and consequently the water vapour mixing ratio, determined by CMH under conditions representative of operation in the UT/LS. No detectable interference in the measured frost point temperature was found for HNO3 mixing ratios of up to 4 ppb for exposure times up to 150 min. HNO3 was observed to co-condense on the mirror frost, with the adsorbed mass increasing linearly with time at constant exposure levels. Over the duration of a typical balloon sonde ascent (90–120 min), the maximum accumulated HNO3 amounts were comparable to monolayer coverage of the geometric mirror surface area, which corresponds to only a small fraction of the actual frost layer surface area. This small amount of co-condensed HNO3 is consistent with the observed lack of HNO3 interference in the frost point measurement because the CMH utilizes significant reductions (>10%) in surface reflectivity by the condensate to determine H2O.

scholarly journals Comparison of in-situ FISH measurements of water vapor in the UTLS with ECMWF (re)analysis data

2014 ◽  
Vol 14 (10) ◽  
pp. 14399-14438 ◽  
Author(s):  
A. Kunz ◽  
N. Spelten ◽  
P. Konopka ◽  
R. Müller ◽  
R. M. Forbes ◽  
...  
Keyword(s):  
Water Vapor ◽  
Analysis Data ◽  
High Water ◽  
Reanalysis Data ◽  
Polar Regions ◽  
Large Set ◽  
Data Set ◽  
Mixing Ratios ◽  
Time Periods

Abstract. An evaluation of water vapor in the UTLS in the atmospheric ERA-Interim reanalysis data set is presented by using in-situ measurements from a large set of airborne measurement campaigns from 2001 to 2011 in the tropics, midlatitudes and polar regions. Water vapor measurements are derived from the Fast In-situ Stratospheric Hygrometer (FISH) and cover isentropic layers from 300–400 K (5–18 km). At the same time, the improvement of the ECMWF assimilation scheme representation of water vapor is addressed for time periods representing different cycles of the Integrated Forecast System (IFS). The ratio Δ(H2O) = H2OERA / H2OFISH is used as a simple measure for the difference between observations and the reanalyses. Overall, the reanalysis data reproduce around 87% of all FISH measurements within Δ(H2O) = 0.5–2, and 30% are within Δ(H2O) = 1.0 ± 0.1. Nevertheless, also strong over- and underestimations occur both in the troposphere and in the stratosphere. Δ(H2O) values indicate deviations of factors up to 10, with lower deviations in the stratosphere (Δ(H2O) = 0.5–4) than in the troposphere (Δ(H2O) = 0.5–10). In the tropical stratosphere the ratio is closer to 1 (Δ(H2O) = 0.5–2) than in the extratropical stratosphere where strong deviations occur (Δ(H2O) = 0.1–4). When considering operational analysis data, the agreement with FISH improves over the time, in particular when comparing water vapor fields for time periods before 2004 and after 2010. It appears that influences of tropical tropospheric and extratropical lower stratospheric processes on the water vapor distribution in the UTLS are particularly challenging, resulting in an overestimation of low and underestimation of high water vapor mixing ratios.

An Impedance Sensor of Water Cut with Three Electrodes and Relative Analysis on Experiment Results

2021 ◽  
Author(s):  
Chuan Yu ◽  
Qinghai Yang ◽  
Songbo Wei ◽  
Ming Li ◽  
Tao Fu
Keyword(s):  
Single Layer ◽  
High Water ◽  
Sensor Calibration ◽  
Mixing Ratios ◽  
Margin Of Error ◽  
Measurement Results ◽  
Oil Water ◽  
High Water Cut ◽  
Water Cut ◽  
Impedance Sensor

Abstract Single-layer water cut measurement is of great significance for identifying and shutting off the unwanted water, analyzing oil remained and optimizing production. Currently, however, only the water cut of multilayer mixture can be measured by testing samples taken from wellhead, a way which is widely used in oilfields. That of single-layer fluid cannot be determined yet To address the problem, this paper puts forward a new impedance sensor that offers long-term online monitoring of single-layer water cut. This sensor is based on the different electrical conductivity of oil and water. It has two layers. The inner one contains three electrodes - two at both sides sending sinusoidal excitation signals and one at the middle receiving signals that have been attenuated by the water-oil medium. With the Maxwell's model of oil-water mixed fluid, the receiver then can measure the water cut online. The outer layer of the sensor is made of PEEK, an insulative protection. In front of the electrodes lies a static mixer which makes the measurement more accurate by fully blending the two media when they flow through the electrodes. Laboratory tests are carried out with the prototype of the sensor at various oil-water mixing ratios, fluid flow rates, and temperatures. Results show that the average margin of error is within ± 3%. Higher accuracy is seen when high water cut and flow rate enable oil globules to disperse more evenly and the space in between to get wider and the RMS error is less than 2%. If the water cut drops below 80%, the aggregation of the droplets will cause wild fluctuation and more errors in the measurement. In addition, the mineralization of the mixture directly changes its conductivity, which largely impacts the result. Meanwhile, temperature can influence the ionic movement intensity and then alter the conductivity of the medium. Therefore, in practice, the sensor calibration needs to be performed according to the range of medium salinity, and the temperature of the medium is collected in real time for temperature compensation. It is shown that after the adjustment, the water cut measurement results have higher accuracy and consistency. The impedance sensor can realize online water cut monitoring for a single-layer, indicated by tests. It is more suitable for the increasing high water cut oilfields in that it is more accurate as the water cut grows.

scholarly journals Historical greenhouse gas concentrations

2016 ◽  
Author(s):  
Malte Meinshausen ◽  
Elisabeth Vogel ◽  
Alexander Nauels ◽  
Katja Lorbacher ◽  
Nicolai Meinshausen ◽  
...  
Keyword(s):  
Climate Change ◽  
Greenhouse Gas ◽  
Radiative Forcing ◽  
Sulfur Hexafluoride ◽  
Climate Model ◽  
Future Climate Change ◽  
Large Set ◽  
Mixing Ratios ◽  
Surface Mixing ◽  
Cooling Effects

Abstract. Atmospheric greenhouse gas concentrations are at unprecedented, record-high levels compared to pre-industrial reconstructions over the last 800,000 years. Those elevated greenhouse gas concentrations warm the planet and together with net cooling effects by aerosols, they are the reason of observed climate change over the past 150 years. An accurate representation of those concentrations is hence important to understand and model recent and future climate change. So far, community efforts to create composite datasets with seasonal and latitudinal information have focused on marine boundary layer conditions and recent trends since 1980s. Here, we provide consolidated data sets of historical atmospheric (volume) mixing ratios of 43 greenhouse gases specifically for the purpose of climate model runs. The presented datasets are based on AGAGE and NOAA networks and a large set of literature studies. In contrast to previous intercomparisons, the new datasets are latitudinally resolved, and include seasonality over the period between year 0 to 2014. We assimilate data for CO2, methane (CH4) and nitrous oxide (N2O), 5 chlorofluorocarbons (CFCs), 3 hydrochlorofluorocarbons (HCFCs), 16 hydrofluorocarbons (HFCs), 3 halons, methyl bromide (CH3Br), 3 perfluorocarbons (PFCs), sulfur hexafluoride (SF6), nitrogen triflouride (NF3) and sulfuryl fluoride (SO2F2). We estimate 1850 annual and global mean surface mixing ratios of CO2 at 284.3 ppmv, CH4 at 808.2 ppbv and N2O at 273.0 ppbv and quantify the seasonal and hemispheric gradients of surface mixing ratios. Compared to earlier intercomparisons, the stronger implied radiative forcing in the northern hemisphere winter (due to the latitudinal gradient and seasonality) may help to improve the skill of climate models to reproduce past climate and thereby reduce uncertainty in future projections.

scholarly journals Diagnosis of processes controlling water vapour in the tropical tropopause layer by a Lagrangian cirrus model

2007 ◽  
Vol 7 (2) ◽  
pp. 5515-5552 ◽  
Author(s):  
C. Ren ◽  
A. R. MacKenzie ◽  
C. Schiller ◽  
G. Shur ◽  
V. Yushkov
Keyword(s):  
Water Vapour ◽  
Specific Humidity ◽  
Mixing Ratio ◽  
Total Water ◽  
Water Mixing ◽  
Tropical Tropopause Layer ◽  
Mixing Ratios ◽  
Aircraft Flight ◽  
Tropical Tropopause ◽  
Ecmwf Model

Abstract. We have developed a Lagrangian air-parcel cirrus model (LACM), to diagnose the processes controlling water in the tropical tropopause layer (TTL). LACM applies parameterised microphysics to air parcel trajectories. The parameterisation includes the homogeneous freezing of aerosol droplets, the growth/sublimation of ice particles, and sedimentation of ice particles, so capturing the main dehydration mechanism for air in the TTL. Rehydration is also considered by resetting the water vapour mixing ratio in an air parcel to the value at the point in the 4-D analysis/forecast data used to generate the trajectories, but only when certain conditions, indicative of convection, are satisfied. These conditions are imposed to confine what processes contribute to rehydration. The conditions act to restrict rehydration of the Lagrangian air parcels to regions where convective transport of water vapour from below is significant, at least to the extent that the analysis/forecast captures this process. The inclusion of hydration and dehydration mechanisms in LACM results in total water fields near tropical convection that have more of the "stripey" character of satellite observations of high cloud, than do either the ECMWF analysis or trajectories without microphysics. The mixing ratios of total water in the TTL, measured by a high-altitude aircraft over Brazil (during the TROCCINOX campaign), have been reconstructed by LACM using trajectories generated from ECMWF analysis. Two other Lagrangian reconstructions are also tested: linear interpolation of ECMWF analysed specific humidity onto the aircraft flight track, and instantaneous dehydration to the saturation vapour pressure over ice along trajectories. The reconstructed total water mixing ratios along aircraft flight tracks are compared with observations from the FISH total water hygrometer. Process-oriented analysis shows that modelled cirrus cloud events are responsible for dehydrating the air parcels coming from lower levels, resulting in total water mixing ratios as low as 2 μmol/mol. Without adding water back to some of the trajectories, the LACM and instantaneous-dehydration reconstructions have a dry bias. The interpolated-ECMWF reconstruction does not suffer this dry bias, because convection in the ECMWF model moistens air parcels dramatically, by pumping moist air upwards. This indicates that the ECMWF model captures the gross features of the rehydration of air in the TTL by convection. Overall, the ECMWF models captures well the exponential decrease in total water mixing ratio with height above 250 hPa, so that all the reconstruction techniques capture more than 75% of the variance in the measured total water mixing ratios over the depth of the TTL. We have therefore developed a simple method for re-setting the total water in LACM using the ECMWF-analysed specific humidity in regions where the model predicts convection. By picking up the main contributing processes to dehydration and rehydration in the TTL, LACM reconstructs total water mixing ratios along aircraft flight tracks at the top of the TTL, close to the cold point, that are always in substantially better agreement with observations than instantaneous-dehydration reconstructions, and better than the ECMWF analysis for regions of high relative humidity and cloud.

scholarly journals Estimating Brewer-Dobson circulation trends from changes in stratospheric water vapour and methane

2021 ◽  
Author(s):  
Liubov Poshyvailo-Strube ◽  
Rolf Müller ◽  
Stephan Fueglistaler ◽  
Michaela I. Hegglin ◽  
Johannes C. Laube ◽  
...  
Keyword(s):  
Water Vapour ◽  
Meridional Overturning Circulation ◽  
Lagrangian Model ◽  
Satellite Measurements ◽  
Mixing Ratios ◽  
Transit Times ◽  
Sensitivity Studies ◽  
Meridional Overturning ◽  
Gas Measurements ◽  
Stratospheric Water Vapour

Abstract. The stratospheric meridional overturning circulation, also referred to as the Brewer-Dobson circulation (BDC), controls the composition of the stratosphere, which, in turn, affects radiation and climate. As the BDC cannot be directly measured, one has to infer its strength and trends indirectly. For instance, trace gas measurements allow the calculation of average transit times. Satellite measurements provide information on the distributions of trace gases for the entire stratosphere, with measurements of particularly long and dense coverage available for stratospheric water vapour (H2O). Although chemical processes and boundary conditions confound interpretation, the influence of CH4 oxidation on H2O is relatively straightforward, and thus H2O is an appealing tracer for transport analysis despite these caveats. In this work, we explore how mean age of air trends can be estimated from the combination of stratospheric H2O and CH4 data. We carry out different sensitivity studies with the Chemical Lagrangian Model of the Stratosphere (CLaMS) and focus on the analysis of the periods of 1990–2006 and 1990–2017. In particular, we assess the methodological uncertainties related to the two commonly-used approximations of (i) instantaneous stratospheric entry mixing ratio propagation, and (ii) constant correlation between mean age and the fractional release factor of methane. Our results show that the estimated mean age of air trends from the combination of observed stratospheric H2O and CH4 changes may be significantly affected by the assumed approximations. Depending on the investigated stratospheric region and the considered period, the error in estimated mean age of air decadal trends can be large – the discrepancies are up to 10 % per decade or even more at the lower stratosphere. For particular periods, the errors from the two approximations can lead to opposite effects, which may even cancel out. Finally, we propose an improvement to the approximation method by using an idealised age spectrum to propagate stratospheric entry mixing ratios. The findings of this work can be used for improving and assessing the uncertainties in stratospheric BDC trend estimation from global satellite measurements.

scholarly journals Matching radiative transfer models and radiosonde data from the EPS/Metop Sodankylä campaign to IASI measurements

2011 ◽  
Vol 4 (6) ◽  
pp. 1177-1189 ◽  
Author(s):  
X. Calbet ◽  
R. Kivi ◽  
S. Tjemkes ◽  
F. Montagner ◽  
R. Stuhlmann
Keyword(s):  
Radiative Transfer ◽  
Water Vapour ◽  
Spectral Region ◽  
Radiosonde Data ◽  
Radiative Transfer Models ◽  
Frost Point ◽  
Instrument Noise ◽  
Atmospheric State ◽  
Dry Bias ◽  
Transfer Models

Abstract. Radiances observed from IASI are compared to calculated ones. Calculated radiances are obtained using several radiative transfer models (OSS, LBLRTM v11.3 and v11.6) on best estimates of the atmospheric state vectors. The atmospheric state vectors are derived from cryogenic frost point hygrometer and humidity dry bias corrected RS92 measurements flown on sondes launched 1 h and 5 min before IASI overpass time. The temperature and humidity best estimate profiles are obtained by interpolating or extrapolating these measurements to IASI overpass time. The IASI observed and calculated radiances match to within one sigma IASI instrument noise in the spectral region where water vapour is a strong absorber (wavenumber, ν, in the range of 1500 ≤ ν ≤ 1570 and 1615 ≤ ν ≤ 1800 cm−1).

Sign in / Sign up

Export Citation Format

Share Document