Influence of injection parameters on the dynamics of Hydraulic Fracturing monitored by Acoustic Emission

2020 ◽  
Author(s):  
Maria Bobrova ◽  
Egor Filev ◽  
Anna Shevtsova ◽  
Sergey Stanchits ◽  
Vladimir Stukachev ◽  
...  
Keyword(s):  
Acoustic Emission ◽  
Hydraulic Fracturing ◽  
Hydraulic Fracture ◽  
Fracture Plane ◽  
Fluid Viscosity ◽  
Breakdown Pressure ◽  
X Ray ◽  
3D Shape ◽  
Injection Parameters ◽  
Maximal Stress

<p>Understanding the processes of Hydraulic Fracturing (HF) initiation and propagation in different types of rocks is important for the design and optimization of HF during the exploitation of underground resources. The main goals were to study the dynamics of the process of hydraulic fracture growth and possible optimization of HF technology for both homogeneous and heterogeneous rocks. Laboratory experiments on HF with different injection parameters were carried out on natural limestone, dolomite and shale specimens. The dynamics of HF process was monitored by Acoustic Emission (AE) technique, on the analogy of induced microseismicity monitoring of HF in the field conditions. The shape of created HF and the size of leak-off zone were analyzed by X-Ray CT scanning technique after the testing.</p><p>Experiments on dolomite were conducted using fluids with different viscosities (1000-10000 cP) injected into the rock with a rate of 0.5 ml/min. In case of low viscosity, we observed low AE activity. After the test, the sample was cut in several pieces transverse to the expected fracture plane. We have found that HF has initiated, but did not reach the sample boundaries and leak-off was significant. The ten times increase of fluid viscosity resulted in significantly increased AE activity, smaller size of leak-off zone and higher breakdown pressure (21.8 against 18.7 MPa). The post-test 3D shape of HF surface obtained by X-Ray CT closely correlates with 3D shape of localized AE events, confirming that the fracture propagated in the direction of maximal stress, as expected. It means that viscosity of fracturing fluid had a significant effect on fracturing breakdown pressure and fracture behavior.</p><p>The influence of different rock types on hydraulic fracturing was studied with dolomite, limestone and shale samples. In case of dolomite and shale, sufficient number of Acoustic Emission events were recorded, which allowed tracing the direction and dynamics of fracture propagation. However, for the limestone, a very small number of AE events were localized with the same parameters of injected fluid. Comparison of dolomite and shale HFs shows that the crack in the shale had a more complex shape, deviating from the maximal stress direction, which was explained by rock heterogeneity, by the presence of natural cracks and inclined planes of weakness. It led us to conclusion that the rock fabric plays an important role in the behavior of hydraulic fracture in heterogeneous rock.</p>

scholarly journals Full-waveform-based characterization of acoustic emission activity in a mine-scale experiment: a comparison of conventional and advanced hydraulic fracturing schemes

2020 ◽  
Vol 222 (1) ◽  
pp. 189-206 ◽  
Author(s):  
Peter Niemz ◽  
Simone Cesca ◽  
Sebastian Heimann ◽  
Francesco Grigoli ◽  
Sebastian von Specht ◽  
...  
Keyword(s):  
Acoustic Emission ◽  
Hydraulic Fracturing ◽  
Induced Seismicity ◽  
Large Scale ◽  
Sampling Rate ◽  
Fracture Plane ◽  
B Values ◽  
Full Waveform ◽  
Scale Experiment ◽  
Fracturing Experiments

SUMMARY Understanding fracturing processes and the hydromechanical relation to induced seismicity is a key question for enhanced geothermal systems (EGS). Commonly massive fluid injection, predominately causing hydroshearing, are used in large-scale EGS but also hydraulic fracturing approaches were discussed. To evaluate the applicability of hydraulic fracturing techniques in EGS, six in situ, multistage hydraulic fracturing experiments with three different injection schemes were performed under controlled conditions in crystalline rock at the Äspö Hard Rock Laboratory (Sweden). During the experiments the near-field ground motion was continuously recorded by 11 piezoelectric borehole sensors with a sampling rate of 1 MHz. The sensor network covered a volume of 30×30×30 m around a horizontal, 28-m-long injection borehole at a depth of 410 m. To extract and characterize massive, induced, high-frequency acoustic emission (AE) activity from continuous recordings, a semi-automated workflow was developed relying on full waveform based detection, classification and location procedures. The approach extended the AE catalogue from 196 triggered events in previous studies to more than 19 600 located AEs. The enhanced catalogue, for the first time, allows a detailed analysis of induced seismicity during single hydraulic fracturing experiments, including the individual fracturing stages and the comparison between injection schemes. Beside the detailed study of the spatio-temporal patterns, event clusters and the growth of seismic clouds, we estimate relative magnitudes and b-values of AEs for conventional, cyclic progressive and dynamic pulse injection schemes, the latter two being fatigue hydraulic fracturing techniques. While the conventional fracturing leads to AE patterns clustered in planar regions, indicating the generation of a single main fracture plane, the cyclic progressive injection scheme results in a more diffuse, cloud-like AE distribution, indicating the activation of a more complex fracture network. For a given amount of hydraulic energy (pressure multiplied by injected volume) pumped into the system, the cyclic progressive scheme is characterized by a lower rate of seismicity, lower maximum magnitudes and significantly larger b-values, implying an increased number of small events relative to the large ones. To our knowledge, this is the first direct comparison of high resolution seismicity in a mine-scale experiment induced by different hydraulic fracturing schemes.

Development of a new approach for hydraulic fracturing in tight sand with pre-existing natural fractures

2016 ◽  
Vol 56 (1) ◽  
pp. 225 ◽  
Author(s):  
Kunakorn Pokalai ◽  
David Kulikowski ◽  
Raymond L. Johnson ◽  
Manouchehr Haghighi ◽  
Dennis Cooke
Keyword(s):  
Hydraulic Fracturing ◽  
Hydraulic Fracture ◽  
High Stress ◽  
Gas Production ◽  
Natural Fracture ◽  
Rock Properties ◽  
Fracture Plane ◽  
Natural Fractures ◽  
Geomechanical Model ◽  
Well Design

Hydraulic fracturing in tight gas reservoirs has been performed in the Cooper Basin for decades in reservoirs containing high stress and pre-existing natural fractures, especially near faults. The hydraulic fracture is affected by factors such as tortuosity, high entry pressures, and the rock fabric including natural fractures. These factors cause fracture plane rotation and complexities, leading to fracture disconnection or reduced proppant placement during the treatment. In this paper, rock properties are estimated for a targeted formation using well logs to create a geomechanical model. Natural fracture and stress azimuths within the interval were interpreted from borehole image logs. The image log interpretations inferred that fissures are oriented 30–60° relative to the maximum horizontal stress. Next, diagnostic fracture injection test (DFIT) data was used with the poro-elastic stress equations to predict tectonic strains. Finally, the geomechanical model was history-matched with a planar 3D hydraulic fracturing simulator, and gave more insight into fracture propagation in an environment of pre-existing natural fractures. The natural fracture azimuths and calibrated geomechanical model are input into a framework to evaluate varying scenarios that might result based on a vertical or inclined well design. A well design is proposed based on the natural fracture orientation relative to the hydraulic fracture that minimises complexity to optimise proppant placement. In addition, further models and diagnostics are proposed to aid predicting the hydraulically induced fracture geometry, its impact on gas production, and optimising wellbore trajectory to positively interact with pre-existing natural fractures.

scholarly journals Effect of Joint Geometrical Parameters on Hydraulic Fracture Network Propagation in Naturally Jointed Shale Reservoirs

Geofluids ◽  
2018 ◽  
Vol 2018 ◽  
pp. 1-23 ◽  
Author(s):  
Zhaohui Chong ◽  
Qiangling Yao ◽  
Xuehua Li
Keyword(s):  
Hydraulic Fracturing ◽  
Hydraulic Fracture ◽  
Fracture Network ◽  
Hydraulic Fractures ◽  
Geometrical Parameters ◽  
Breakdown Pressure ◽  
Opening Mode ◽  
Hydraulic Fracture Network ◽  
Shale Reservoirs ◽  
Network Pattern

The presence of a significant amount of discontinuous joints results in the inhomogeneous nature of the shale reservoirs. The geometrical parameters of these joints exert effects on the propagation of a hydraulic fracture network in the hydraulic fracturing process. Therefore, mechanisms of fluid injection-induced fracture initiation and propagation in jointed reservoirs should be well understood to unleash the full potential of hydraulic fracturing. In this paper, a coupled hydromechanical model based on the discrete element method is developed to explore the effect of the geometrical parameters of the joints on the breakdown pressure, the number and proportion of hydraulic fractures, and the hydraulic fracture network pattern generated in shale reservoirs. The microparameters of the matrix and joint used in the shale reservoir model are calibrated through the physical experiment. The hydraulic parameters used in the model are validated through comparing the breakdown pressure derived from numerical modeling against that calculated from the theoretical equation. Sensitivity analysis is performed on the geometrical parameters of the joints. Results demonstrate that the HFN pattern resulting from hydraulic fracturing can be roughly divided into four types, i.e., crossing mode, tip-to-tip mode, step path mode, and opening mode. As β (joint orientation with respect to horizontal principal stress in plane) increases from 0° to 15° or 30°, the hydraulic fracture network pattern changes from tip-to-tip mode to crossing mode, followed by a gradual decrease in the breakdown pressure and the number of cracks. In this case, the hydraulic fracture network pattern is controlled by both γ (joint step angle) and β. When β is 45° or 60°, the crossing mode gains dominance, and the breakdown pressure and the number of cracks reach the lowest level. In this case, the HFN pattern is essentially dependent on β and d (joint spacing). As β reaches 75° or 90°, the step path mode is ubiquitous in all shale reservoirs, and the breakdown pressure and the number of the cracks both increase. In this case, β has a direct effect on the HFN pattern. In shale reservoirs with the same β, either decrease in k (joint persistency) and e (joint aperture) or increase in d leads to the increase in the breakdown pressure and the number of cracks. It is also found that changes in d and e result in the variation in the proportion of different types of hydraulic fractures. The opening mode of the hydraulic fracture network pattern is observed when e increases to 1.2 × 10−2 m.

scholarly journals Numerical simulation of horizontal well network fracturing in glutenite reservoir

2018 ◽  
Vol 73 ◽  
pp. 53
Author(s):  
Minhui Qi ◽  
Mingzhong Li ◽  
Yanchao Li ◽  
Tiankui Guo ◽  
Song Gao
Keyword(s):  
Numerical Simulation ◽  
Hydraulic Fracturing ◽  
Hydraulic Fracture ◽  
Horizontal Well ◽  
Fracture Propagation ◽  
Simulation Method ◽  
Fracture Network ◽  
Fluid Viscosity ◽  
Coupled Flow ◽  
Hydraulic Fracture Propagation

Hydraulic fracturing is an economically effective technology developing the glutenite reservoirs, which have far stronger heterogeneity than the conventional sandstone reservoir. According to the field production experience of Shengli Oilfield, horizontal-well fracturing is more likely to develop a complex fractured network, which improves the stimulated volume of reservoir effectively. But the clear mechanism of horizontal-well hydraulic fracture propagation in the glutenite reservoirs is still not obtained, thus it is difficult to effectively carry out the design of fracturing plan. Based on the characteristics of the glutenite reservoirs, a coupled Flow-Stress-Damage (FSD) model of hydraulic fracture propagation is established. The numerical simulation of fracturing expansion in the horizontal well of the glutenite reservoir is conducted. It is shown that a square mesh-like fracture network is developed near the horizontal well in the reservoir with lower stress difference, in which fracture is more prone to propagate along the direction of the minimum principal stress as well. High fracturing fluids injection displacement and high fracturing fluid viscosity lead to the rise of static pressure of the fracture, which results in the rise of fracture complexity, and greater probability to deflect when encountering gravels. As the perforation density increases, the micro-fractures generated at each perforation gather together faster, and the range of the stimulated reservoir is also relatively large. For reservoirs with high gravel content, the complexity of fracture network and the effect of fracture communication are obviously increased, and the range of fracture deflection is relatively large. In the case of the same gravel distribution, the higher the tensile strength of the gravel, the greater fracture tortuosity and diversion was observed. In this paper, a simulation method of horizontal well fracture network propagation in the reservoirs is introduced, and the result provides the theoretical support for fracture network morphology prediction and plan design of hydraulic fracturing in the glutenite reservoir.

scholarly journals A multi-perforation staged fracturing experimental study on hydraulic fracture initiation and propagation

2020 ◽  
Vol 38 (6) ◽  
pp. 2466-2484
Author(s):  
Jianguang Wei ◽  
Saipeng Huang ◽  
Guangwei Hao ◽  
Jiangtao Li ◽  
Xiaofeng Zhou ◽  
...  
Keyword(s):  
Hydraulic Fracturing ◽  
Hydraulic Fracture ◽  
Oil And Gas ◽  
Fracture Initiation ◽  
Fracture Network ◽  
Hydraulic Fractures ◽  
Breakdown Pressure ◽  
Tight Sandstone ◽  
Heterogeneous Samples ◽  
Initiation And Propagation

Hydraulic fracture initiation and propagation are extremely important on deciding the production capacity and are crucial for oil and gas exploration and development. Based on a self-designed system, multi-perforation cluster-staged fracturing in thick tight sandstone reservoir was simulated in the laboratory. Moreover, the technology of staged fracturing during casing completion was achieved by using a preformed perforated wellbore. Three hydraulic fracturing methods, including single-perforation cluster fracturing, multi-perforation cluster conventional fracturing and multi-perforation cluster staged fracturing, were applied and studied, respectively. The results clearly indicate that the hydraulic fractures resulting from single-perforation cluster fracturing are relatively simple, which is difficult to form fracture network. In contrast, multi-perforation cluster-staged fracturing has more probability to produce complex fractures including major fracture and its branched fractures, especially in heterogeneous samples. Furthermore, the propagation direction of hydraulic fractures tends to change in heterogeneous samples, which is more likely to form a multi-directional hydraulic fracture network. The fracture area is greatly increased when the perforation cluster density increases in multi-perforation cluster conventional fracturing and multi-perforation cluster-staged fracturing. Moreover, higher perforation cluster densities and larger stage numbers are beneficial to hydraulic fracture initiation. The breakdown pressure in homogeneous samples is much higher than that in heterogeneous samples during hydraulic fracturing. In addition, the time of first fracture initiation has the trend that the shorter the initiation time is, the higher the breakdown pressure is. The results of this study provide meaningful suggestions for enhancing the production mechanism of multi-perforation cluster staged fracturing.

scholarly journals Study on Propagation Behaviors of Hydraulic Fracture Network in Tight Sandstone Formation with Closed Cemented Natural Fractures

Geofluids ◽  
2020 ◽  
Vol 2020 ◽  
pp. 1-22
Author(s):  
Jun Zhang ◽  
Yu-Wei Li ◽  
Wei Li ◽  
Zi-Jie Chen ◽  
Yuan Zhao ◽  
...  
Keyword(s):  
Hydraulic Fracturing ◽  
Hydraulic Fracture ◽  
Fracture Network ◽  
In Situ Stress ◽  
Injection Rate ◽  
Fluid Viscosity ◽  
Tight Sandstone ◽  
Propagation Behavior ◽  
Sandstone Formation

Natural fractures in tight sandstone formation play a significant role in fracture network generation during hydraulic fracturing. This work presents an experimental model of tight sandstone with closed cemented preexisting fractures. The influence of closed cemented fractures’ (CCF) directions on the propagation behavior of hydraulic fracture (HF) is studied based on the hydraulic fracturing experiment. A field-scaled numerical model used to simulate the propagation of HF is established based on the flow-stress-damage (FSD) coupled method. This model contains the discrete fracture network (DFN) generated by the Monte-Carlo method and is used to investigate the effects of CCFs’ distribution, CCFs’ strength, and in-situ stress anisotropy, injection rate, and fluid viscosity on the propagation behavior of fracture network. The results show that the distribution direction of CCFs is critical for the formation of complex HFs. When the angle between the horizontal maximum principal stress direction and the CCFs is in the range of 30° to 60°, the HF network is the most complex. There are many kinds of compound fracture propagation patterns, such as crossing, branching, and deflection. The increase of CCFs’ strength is not conducive to the generation of branched and deflected fractures. When the in-situ stress difference ranges from 3 MPa to 6 MPa, the HF network’s complexity and propagation range can be guaranteed simultaneously. The increase in the injection rate will promote the formation of the complex HF network. The proper increase of fracturing fluid viscosity can promote HF’s propagation. However, when the viscosity is too high, the complex HFs only appear around the wellbore. The research results can provide new insights for the hydraulic fracturing optimization design of naturally fractured tight sandstone formation.

scholarly journals Numerical Investigation of Hydraulic Fracture Propagation in Naturally Fractured Reservoirs Based on Lattice Spring Model

Geofluids ◽  
2020 ◽  
Vol 2020 ◽  
pp. 1-18
Author(s):  
Kaikai Zhao ◽  
Pengfei Jiang ◽  
Yanjun Feng ◽  
Xiaodong Sun ◽  
Lixing Cheng ◽  
...  
Keyword(s):  
Hydraulic Fracturing ◽  
Hydraulic Fracture ◽  
Fractured Reservoirs ◽  
Fracture Propagation ◽  
Maximum Principal Stress ◽  
Injection Rate ◽  
Naturally Fractured Reservoirs ◽  
Fluid Viscosity ◽  
Global Orientation ◽  
Hf Propagation

Hydraulic fracturing has been extensively employed for permeability enhancement in low-permeability reservoirs. The geometry of the hydraulic fracture network (HFN) may have implications for the optimization of hydraulic fracturing operations. Various parameters, including the in situ stress, treatment parameters (injection rate and fluid viscosity), and orientation of natural fractures (NFs), can significantly affect the interactions between hydraulic fracture (HF) and NFs and the final HFN. In this study, a lattice-spring code was employed to determine the impact of various parameters on the geometry of the HFN. The modelling results indicated that with a large stress difference, the global orientation of the fracture propagation was restricted to the direction of maximum principal stress, and the number of fracture branches was reduced. The geometry of the HFN changed from circular to elliptical. In contrast, with an increase in the fluid viscosity/injection rate, the evolution of the geometry of the HFN exhibited the opposite trend. The global orientation of HF propagation tended to remain parallel to the direction of maximum principal stress, regardless of the branching and tortuosity of the fracture. The variations in the ratio of tensile fracture (HF) to shear fracture (shear slip on NF) can be significant, depending on the stress state, treatment parameters, and preexisting NF network, which determine the dominant stimulation mechanism. This study provides insight into the HF propagation in naturally fractured reservoirs.

Integration of Dynamic Microseismic Data With a True 3D Modeling of Hydraulic-Fracture Propagation in the Vaca Muerta Shale

SPE Journal ◽  
2017 ◽  
Vol 22 (06) ◽  
pp. 1714-1738 ◽  
Author(s):  
Mahdi Haddad ◽  
Jing Du ◽  
Sandrine Vidal-Gilbert
Keyword(s):  
Hydraulic Fracturing ◽  
Hydraulic Fracture ◽  
Fracture Propagation ◽  
Natural Fracture ◽  
Zone Model ◽  
Fluid Viscosity ◽  
Fracture Intersection ◽  
Vaca Muerta ◽  
Hydraulic Fracture Propagation ◽  
Microseismic Events

Summary Microseismic mapping during the hydraulic-fracturing processes in the Vaca Muerta (VM) Shale in Argentina shows a group of microseismic events occurring at shallower depth and at later injection time, and they clearly deviate from the growing planar hydraulic fracture. This spatial and temporal behavior of these shallow microseismic events incurs some questions regarding the nature of these events and their connectivity to the hydraulic fracture. To answer these questions, in this article, we investigate these phenomena by use of a true 3D fracture-propagation-modeling tool along with statistical analysis on the properties of microseismic events. First, we propose a novel technique in Abaqus incorporating fracture intersections in true 3D hydraulic-fracture-propagation simulations by use of a pore-pressure cohesive zone model (CZM), which is validated by comparing our numerical results with the Khristianovic-Geertsma-de Klerk (KGD) solution (Khristianovic and Zheltov 1955; Geertsma and de Klerk 1969). The simulations fully couple slot flow in the fracture with poroelasticity in the matrix and continuum-based leakoff on the fracture walls, and honor the fracture-tip effects in quasibrittle shales. By use of this model, we quantify vertical-natural-fracture activation and fluid infiltration depending on reservoir depth, fracturing-fluid viscosity, mechanical properties of the natural-fracture cohesive layer, natural-fracture conductivity, and horizontal stress contrast. The modeling results demonstrate this natural-fracture activation in coincidence with the hydraulic-fracture-growth complexities at the intersection, such as height throttling, sharp aperture reduction after the intersection, and multibranching at various heights and directions. Finally, we investigate the hydraulic-fracture intersection with a natural fracture in the multilayer VM Shale. We infer the natural-fracture location and orientation from the microseismic-events map and formation microimager log in a nearby vertical well, respectively. We integrate the other field information such as mechanical, geological, and operational data to provide a realistic hydraulic-fracturing simulation in the presence of a natural fracture. Our 3D fracturing simulations equipped with the new fracture-intersection model rigorously simulate the growth of a realistic hydraulic-connection path toward the natural fracture at shallower depths, which was in agreement with our microseismic observations.

scholarly journals Experimental Study on the Propagation Characteristics of Hydraulic Fracture in Clayey-Silt Sediments

Geofluids ◽  
2021 ◽  
Vol 2021 ◽  
pp. 1-13
Author(s):  
Cheng Lu ◽  
Xuwen Qin ◽  
Wenjing Mao ◽  
Chao Ma ◽  
Lantao Geng ◽  
...  
Keyword(s):  
Hydraulic Fracturing ◽  
Hydraulic Fracture ◽  
Confining Pressure ◽  
Gas Production ◽  
Propagation Mechanism ◽  
Propagation Characteristics ◽  
Breakdown Pressure ◽  
Hydrate Dissociation ◽  
Clayey Silt ◽  
Hydrate Reservoirs

The low permeability of clayey-silt hydrate reservoirs in the South China Sea affects the thermal and pressure conductivity of the reservoir, which is difficult to spread to the far end of the wellbore and achieve commercial gas production. In this respect, enhancing the permeability to assist depressurization is necessary. Hydraulic fracturing is a promising reservoir stimulation method for gas hydrate reservoirs. Up to now, majorities of research focus on the fracability of hydrate-bearing sandy sediments, but the studies rarely involved fracture propagation characteristics of clayey-silt sediments in the hydrate dissociation area. In this paper, three sets of hydraulic fracturing experiments under different confining pressure were carried out using the clayey-silt sediments in the Shenhu Area. Computed tomographic (CT) images indicated that clayey-silt sediments could be artificially fractured, and the fracturing fluid could induce tensile fractures and local shear fractures. A multimorphological fracture zone occurred near the borehole. Furthermore, the greater the confining pressure imposed, the greater the breakdown pressure was, and the microfracture arose more easily. The fractures at the top were generally wider than those at the bottom with the same confining pressure. The experimental results could reveal the fracture initiation and propagation mechanism of clayey-silt sediments and provide theoretical support for hydraulic fracture in the hydrate dissociation area.

Sign in / Sign up

Export Citation Format

Share Document