Strength and permeability evolution of andesite during benchtop acid dissolution experiments: implications for volcanic systems

Author(s):  
Jamie Farquharson ◽  
Bastien Wild ◽  
Alexandra Kushnir ◽  
Michael Heap ◽  
Patrick Baud ◽  
...  

<p>Acidic crater lakes are common features of subaerial volcanic systems; indeed, research suggests the existence of over 700 volcanic lakes around the world. Their persistence requires a regular input of water (e.g., meteoric water) at a rate that exceeds the migration of fluid from the system—for example, due to evaporation or fluid flow through the porous edifice.  Flank aquifers and fumarole fields may similarly be strongly acidic environments.</p><p>In order to explore the evolution of the physical and mechanical properties of an andesite under these field-relevant chemical conditions, we performed batch reaction experiments over timescales from 1 day to 4 months. The experiments involved immersion of a suite of samples in a solution of sulfuric acid (0.125 M; pH ∼0.6). Periodically, samples were removed and their physical and mechanical properties measured. We observe a progressive loss of sample mass, along with a general increase in porosity. We attribute this to the dissolution of plagioclase,  accompanied by the generation of a microporous diktytaxitic groundmass due to glass dissolution.</p><p>Plagioclase phenocrysts are seen to undergo progressive pseudomorphic replacement by an amorphous phase enriched in silica and depleted in other, relatively more soluble, cations (Na, Ca, and Al). In the first phase of dissolution (i.e. between 1 and 10 days), this process appears to be confined to preexisting fractures within the plagioclase phenocrysts. Ultimately, however, these phenocrysts tend toward entire replacement by amorphous silica. We do not observe evidence of induced dissolution or alteration in the other mineral constituents of the material: pyroxene, cristobalite, and titanomagnetite, specifically.</p><p>Examining the required Klinkenberg corrections during permeability measurements, we quantitatively demonstrate that the relative aperture of flow pathways increases with progressive acid immersion, by as much as a factor of five. We propose that the dissolution process results in the widening of pore throats and the improvement of pore connectivity, with the effect of increasing permeability by over an order of magnitude relative to the initial measurements. Compressive strength of our samples was also decreased, insofar as porosity tends to increase.</p><p>We highlight broader implications of the observed permeability increase and strength reduction for volcanic systems including induced flank failure and related hazards, improved efficiency of volatile migration, and attendant eruption implications.</p>

2021 ◽  
Vol 75 (3) ◽  
pp. 147-154
Author(s):  
Ivana Sekler ◽  
Suncica Vjestica ◽  
Vladimir Jankovic ◽  
Slobodan Stefanovic ◽  
Vladica Ristic

A perennial plant Miscanthus x giganteus has found its habitat and multiple applications in Europe, despite the fact that it originates from Asia. This study presents the potential use of this plant in new lightweight concrete materials so-called bio-concretes. The above-ground part of the plant was harvested, dried, crushed, and mixed with binders in different proportions. After casting and drying, the samples were characterized physical and mechanical properties. The results have shown that the sample with a higher content of binders while smaller miscanthus granulation and casted in molds under higher pressure exhibited the highest values of the compressive strength and density. In specific, the density was in the order of magnitude of that reported for other types of lightweight concrete with organic fillers, such as sawdust-based concrete ("Durisol"), which further justifies the use of miscanthus for these purposes.


2012 ◽  
Vol 4 (1) ◽  
pp. 1
Author(s):  
Djoko Purwanto

Timber Acacia mangium (Acacia mangium, Willd) for Furniture. The study aims to determine the mechanical and physical properties and the decorative value (color and fiber) wood of acacia mangium with using finishing materials. This type of finishing material used is ultran lasur natural dof ,ultran lasur classic teak, aqua politur clear dof, aqua politur akasia dan aqua politur cherry. After finishing the wood is stored for 3 months. Test parameters were observed, namely, physical and mechanical properties of wood, adhesion of finishing materials, color and appearance of the fiber, and timber dimensions expansion. The results showed that the mechanical physical properties of acacia wood qualified SNI. 01-0608-89 about the physical and mechanical properties of wood for furniture, air dry the moisture content from 13.78 to 14.89%, flexural strength from 509.25 to 680.50 kg/cm2, and compressive strength parallel to fiber 342.1 - 412.9 kg/cm2. Finishing the treatment process using five types of finishing materials can increase the decorative value (color and fiber) wood. Before finishing the process of acacia mangium wood has the appearance of colors and fibers and less attractive (scale scores 2-3), after finishing acacia wood fibers have the appearance of colors and interesting and very interesting (scale 4-5).Keywords: mangium wood, mechanical properties, decorative value, finishing, furniture.


2016 ◽  
Vol 13 (2) ◽  
pp. 67
Author(s):  
Engku Liyana Zafirah Engku Mohd Suhaimi ◽  
Jamil Salleh ◽  
Suzaini Abd Ghani ◽  
Mohamad Faizul Yahya ◽  
Mohd Rozi Ahmad

An investigation on the properties of Tenun Pahang fabric performances using alternative yarns was conducted. The studies were made in order to evaluate whether the Tenun Pahang fabric could be produced economically and at the same time maintain the fabric quality. Traditional Tenun Pahang fabric uses silk for both warp and weft. For this project, two alternative yarns were used which were bamboo and modal, which were a little lower in cost compared to silk. These yarns were woven with two variations, one with the yarns as weft only while maintaining the silk warp and the other with both warp and weft using the alternative yarns. Four (4) physical testings and three (3) mechanical testings conducted on the fabric samples. The fabric samples were evaluated including weight, thickness, thread density, crease recovery angle, stiffness and drapability. The results show that modal/silk and bamboo silk fabrics are comparable in terms of stiffness and drapability, hence they have the potential to replace 100% silk Tenun Pahang.


2014 ◽  
Vol 62 (1) ◽  
pp. 129-137
Author(s):  
A. Sawicki ◽  
J. Mierczyński

Abstract A basic set of experiments for the determination of mechanical properties of sands is described. This includes the determination of basic physical and mechanical properties, as conventionally applied in soil mechanics, as well as some additional experiments, which provide further information on mechanical properties of granular soils. These additional experiments allow for determination of steady state and instability lines, stress-strain relations for isotropic loading and pure shearing, and simple cyclic shearing tests. Unconventional oedometric experiments are also presented. Necessary laboratory equipment is described, which includes a triaxial apparatus equipped with local strain gauges, an oedometer capable of measuring lateral stresses and a simple cyclic shearing apparatus. The above experiments provide additional information on soil’s properties, which is useful in studying the following phenomena: pre-failure deformations of sand including cyclic loading compaction, pore-pressure generation and liquefaction, both static and caused by cyclic loadings, the effect of sand initial anisotropy and various instabilities. An important feature of the experiments described is that they make it possible to determine the initial state of sand, defined as either contractive or dilative. Experimental results for the “Gdynia” model sand are shown.


Author(s):  
Thais Helena Sydenstricker Flores-Sahagun ◽  
Kelly Priscila Agapito ◽  
ROSA MARIA JIMENEZ AMEZCUA ◽  
Felipe Jedyn

2020 ◽  
pp. 39-48
Author(s):  
B. O. Bolshakov ◽  
◽  
R. F. Galiakbarov ◽  
A. M. Smyslov ◽  
◽  
...  

The results of the research of structure and properties of a composite compact from 13 Cr – 2 Мо and BN powders depending on the concentration of boron nitride are provided. It is shown that adding boron nitride in an amount of more than 2% by weight of the charge mixture leads to the formation of extended grain boundary porosity and finely dispersed BN layers in the structure, which provides a high level of wearing properties of the material. The effect of boron nitride concentration on physical and mechanical properties is determined. It was found that the introduction of a small amount of BN (up to 2 % by weight) into the compacts leads to an increase in plasticity, bending strength, and toughness by reducing the friction forces between the metal powder particles during pressing and a more complete grain boundary diffusion process during sintering. The formation of a regulated structure-phase composition of powder compacts of 13 Cr – 2 Mо – BN when the content of boron nitride changes in them allows us to provide the specified physical and mechanical properties in a wide range. The obtained results of studies of the physical and mechanical characteristics of the developed material allow us to reasonably choose the necessary composition of the powder compact for sealing structures of the flow part of steam turbines, depending on their operating conditions.


Sign in / Sign up

Export Citation Format

Share Document