scholarly journals Miscanthus x giganteus as a building material - lightweight concrete

2021 ◽  
Vol 75 (3) ◽  
pp. 147-154
Author(s):  
Ivana Sekler ◽  
Suncica Vjestica ◽  
Vladimir Jankovic ◽  
Slobodan Stefanovic ◽  
Vladica Ristic

A perennial plant Miscanthus x giganteus has found its habitat and multiple applications in Europe, despite the fact that it originates from Asia. This study presents the potential use of this plant in new lightweight concrete materials so-called bio-concretes. The above-ground part of the plant was harvested, dried, crushed, and mixed with binders in different proportions. After casting and drying, the samples were characterized physical and mechanical properties. The results have shown that the sample with a higher content of binders while smaller miscanthus granulation and casted in molds under higher pressure exhibited the highest values of the compressive strength and density. In specific, the density was in the order of magnitude of that reported for other types of lightweight concrete with organic fillers, such as sawdust-based concrete ("Durisol"), which further justifies the use of miscanthus for these purposes.

2010 ◽  
Vol 2 (6) ◽  
pp. 50-55
Author(s):  
Marija Vaičienė ◽  
Jurgita Malaiškienė

Binder material is the most expensive raw component of concrete; thus, scientists are looking for cheaper substitute materials. This paper shows that when manufacturing, a part of the binder material of expanded-clay lightweight concrete can be replaced with active filler. The conducted studies show that technogenic – catalyst waste could act as similar filler. The study also includes the dependence of the physical and mechanical properties of expanded-clay lightweight concrete on the concrete mixture and the chemical composition of the samples obtained. Different formation and composition mixtures of expanded-clay lightweight concrete were chosen to determine the properties of physical-mechanical properties such as density, water absorption and compressive strength.


2016 ◽  
Vol 9 (1) ◽  
pp. 29-33
Author(s):  
MB Hossain ◽  
KM Shaad ◽  
MS Rahman ◽  
P Bhowmik

This research was carried out to investigate various physical properties of Rice Husk Ash (RHA) and, some physical and mechanical properties of concrete incorporating RHA in different proportions. The concrete specimens were tested at 7, 21 and 28 days after curing. Test results revealed that the specific gravity of RHA was found lower than that of sand. The density of concrete containing RHA was recorded between 80-110 lb.ft-3, which is lower than conventional concrete. Water absorption was found increasing with the increase of RHA content in concrete specimens. There were significant variations in compressive strength values of concrete containing 5%, 10% and 20% volume of RHA. The compressive strength of 5% RHA specimen was 150-200% higher than that of other specimens. Hence, upto 5% replacement of RHA could be recommended for making normal lightweight concrete. The splitting tensile strength was about 9-10% of compressive strength. It was concluded that upto 5% RHA can be used effectively in making normal lightweight concrete. The higher percentage of RHA could be used in making non-structural concrete where the strength of concrete is not concerned.J. Environ. Sci. & Natural Resources, 9(1): 29-33 2016


2017 ◽  
Vol 4 (2) ◽  
pp. 21
Author(s):  
Olindo Savi ◽  
Rafael Alves Souza ◽  
Nilson Tadeu Mascia ◽  
Mateus Henrique Souza

This study analyses the physical properties of recycled gypsum and mechanical performance of pre-molded gypsum panels made of recycled gypsum. A compatation with commercial gypsum physical properties and mechanica behavior of pre-molded commercial gypsum panels is also carried out. After collection, recycling and grinding gypsum residues, the quality of the powder produced was evaluated in terms of units of mass and fineness modulus. Additional tests of the dry paste were conducted for assessment of hardness, water absorption, and compressive strength of recycled gypsum. The commercial potential of the material was evaluated by the bending strength testing pre-molded panels. The results demonstrate that gypsum recycling is sustainable, ecologically correct and feasible for the production of pre-molded elements with great potential use in civil construction. Keywords: gypsum panels, mixed pastes, sustainable, gypsum pastes.


2012 ◽  
Vol 4 (1) ◽  
pp. 1
Author(s):  
Djoko Purwanto

Timber Acacia mangium (Acacia mangium, Willd) for Furniture. The study aims to determine the mechanical and physical properties and the decorative value (color and fiber) wood of acacia mangium with using finishing materials. This type of finishing material used is ultran lasur natural dof ,ultran lasur classic teak, aqua politur clear dof, aqua politur akasia dan aqua politur cherry. After finishing the wood is stored for 3 months. Test parameters were observed, namely, physical and mechanical properties of wood, adhesion of finishing materials, color and appearance of the fiber, and timber dimensions expansion. The results showed that the mechanical physical properties of acacia wood qualified SNI. 01-0608-89 about the physical and mechanical properties of wood for furniture, air dry the moisture content from 13.78 to 14.89%, flexural strength from 509.25 to 680.50 kg/cm2, and compressive strength parallel to fiber 342.1 - 412.9 kg/cm2. Finishing the treatment process using five types of finishing materials can increase the decorative value (color and fiber) wood. Before finishing the process of acacia mangium wood has the appearance of colors and fibers and less attractive (scale scores 2-3), after finishing acacia wood fibers have the appearance of colors and interesting and very interesting (scale 4-5).Keywords: mangium wood, mechanical properties, decorative value, finishing, furniture.


CivilEng ◽  
2021 ◽  
Vol 2 (2) ◽  
pp. 523-540
Author(s):  
Imed Beghoura ◽  
Joao Castro-Gomes

This study focuses on the development of an alkali-activated lightweight foamed material (AA-LFM) with enhanced density. Several mixes of tungsten waste mud (TWM), grounded waste glass (WG), and metakaolin (MK) were produced. Al powder as a foaming agent was added, varying from 0.009 w.% to 0.05 w.% of precursor weight. Expanded granulated cork (EGC) particles were incorporated (10% to 40% of the total volume of precursors). The physical and mechanical properties of the foamed materials obtained, the effects of the amount of the foaming agent and the percentage of cork particles added varying from 10 vol.% to 40% are presented and discussed. Highly porous structures were obtained, Pore size and cork particles distribution are critical parameters in determining the density and strength of the foams. The compressive strength results with different densities of AA-LFM obtained by modifying the foaming agent and cork particles are also presented and discussed. Mechanical properties of the cured structure are adequate for lightweight prefabricated building elements and components.


2012 ◽  
Vol 2012 ◽  
pp. 1-5 ◽  
Author(s):  
Eethar Thanon Dawood ◽  
Mahyuddin Ramli

This study was conducted to determine some physical and mechanical properties of high-strength flowable mortar reinforced with different percentages of palm fiber (0, 0.2, 0.4, 0.6, 0.8, 1.0, 1.2, 1.4, and 1.6% as volumetric fractions). The density, compressive strength, flexural strength, and toughness index were tested to determine the mechanical properties of this mortar. Test results illustrate that the inclusion of this fiber reduces the density of mortar. The use of 0.6% of palm fiber increases the compressive strength and flexural strength by about 15.1%, and 16%, respectively; besides, the toughness index (I5) of the high-strength flowable mortar has been significantly enhanced by the use of 1% and more of palm fiber.


2013 ◽  
Vol 357-360 ◽  
pp. 1082-1085 ◽  
Author(s):  
Kamarul Aini Mohd Sari ◽  
Sohif Mat ◽  
Khairiah Haji Badri ◽  
Muhammad Fauzi Mohd Zain

An experimental program was performed to obtain the density, compressive strength, and thermal conductivity of palm-based lightweight concrete. Palm-based polyurethane (PU) particles were used as lightweight aggregates in creating concrete systems. Concrete systems contain palm kernel oil-based polyol (PKO-p) reacted with 2,4-methylene diphenyl diisocyanate (MDI). In this study, polymer concrete was improved to achieve the optimum level of PU with the lowest possible density. The PU particles in the concrete mixture comprised of 1% to 5% w/w with density of less than 1800 kg/m3. The PU particles were 5 mm in size. The ratio of PKO-p to MDI was set at 1:1 and the loading of the concrete mixture was set at 3% w/w to produce lightweight concrete. The resulting concrete has excellent compressive strength (17.5 MPa) and thermal conductivity (0.24 W/mK). Results show that the PU particle dosage has the most significant effect on the physical and mechanical properties of concrete.


2018 ◽  
Vol 2018 ◽  
pp. 1-12 ◽  
Author(s):  
Neslihan Doğan-Sağlamtimur ◽  
Adnan Güven ◽  
Ahmet Bilgil

Pumice, cements (CEM I- and CEM II-type), waste fly and bottom ashes (IFA, GBA, and BBA) supplied from international companies were used to produce lightweight building materials, and physical-mechanical properties of these materials were determined. Axial compressive strength (ACS) values were found above the standards of 4 and 8 MPa (Bims Concrete (BC) 40 and 80 kgf/cm2 class) for cemented (CEM I) pumice-based samples. On the contrary, the ACS values of the pumice-based cemented (CEM II) samples could not be reached to these standards. Best ACS results (compatible with BC80) from these cemented lightweight material samples produced with the ashes were found in 50% mixing ratio as 10.6, 13.2, and 20.5 MPa for BBA + CEM I, GBA + CEM II, and IFA + CEM I, respectively, and produced with pumice were found as 8.4 MPa (same value) for GBA + pumice + CEM II (in 25% mixing ratio), BBA + pumice + CEM I (in 100% mixing ratio), and pumice + IFA + CEM I (in 100% mixing ratio), respectively. According to the results, cemented ash-based lightweight building material produced with and without pumice could widely be used for constructive purposes. As a result of this study, an important input to the ecosystem has been provided using waste ashes, whose storage constitutes a problem.


2021 ◽  
Author(s):  
Jamie Farquharson ◽  
Bastien Wild ◽  
Alexandra Kushnir ◽  
Michael Heap ◽  
Patrick Baud ◽  
...  

<p>Acidic crater lakes are common features of subaerial volcanic systems; indeed, research suggests the existence of over 700 volcanic lakes around the world. Their persistence requires a regular input of water (e.g., meteoric water) at a rate that exceeds the migration of fluid from the system—for example, due to evaporation or fluid flow through the porous edifice.  Flank aquifers and fumarole fields may similarly be strongly acidic environments.</p><p>In order to explore the evolution of the physical and mechanical properties of an andesite under these field-relevant chemical conditions, we performed batch reaction experiments over timescales from 1 day to 4 months. The experiments involved immersion of a suite of samples in a solution of sulfuric acid (0.125 M; pH ∼0.6). Periodically, samples were removed and their physical and mechanical properties measured. We observe a progressive loss of sample mass, along with a general increase in porosity. We attribute this to the dissolution of plagioclase,  accompanied by the generation of a microporous diktytaxitic groundmass due to glass dissolution.</p><p>Plagioclase phenocrysts are seen to undergo progressive pseudomorphic replacement by an amorphous phase enriched in silica and depleted in other, relatively more soluble, cations (Na, Ca, and Al). In the first phase of dissolution (i.e. between 1 and 10 days), this process appears to be confined to preexisting fractures within the plagioclase phenocrysts. Ultimately, however, these phenocrysts tend toward entire replacement by amorphous silica. We do not observe evidence of induced dissolution or alteration in the other mineral constituents of the material: pyroxene, cristobalite, and titanomagnetite, specifically.</p><p>Examining the required Klinkenberg corrections during permeability measurements, we quantitatively demonstrate that the relative aperture of flow pathways increases with progressive acid immersion, by as much as a factor of five. We propose that the dissolution process results in the widening of pore throats and the improvement of pore connectivity, with the effect of increasing permeability by over an order of magnitude relative to the initial measurements. Compressive strength of our samples was also decreased, insofar as porosity tends to increase.</p><p>We highlight broader implications of the observed permeability increase and strength reduction for volcanic systems including induced flank failure and related hazards, improved efficiency of volatile migration, and attendant eruption implications.</p>


Author(s):  
Haopeng Jiang ◽  
Annan Jiang ◽  
Fengrui Zhang

Experimental tests were conducted to study the influence of natural cooling and water cooling on the physical and mechanical properties of quartz sandstone. This study aims to understand the effect of different cooling methods on the physical and mechanical properties of quartz sandstone (such as mass, volume, density, P-wave velocity, elastic modulus, uniaxial compressive strength, etc.). The results show that the uniaxial compressive strength (UCS) and elastic modulus(E) of the specimens cooled by natural-cooling and water-cooling decrease with heating temperature. At 800℃, after natural cooling and water cooling, the average value of UCS decreased by 34.65% and 57.90%, and the average value of E decreased by 87.66% and 89.05%, respectively. Meanwhile, scanning electron microscope (SEM) images were used to capture the development of microcracks and pores within the specimens after natural-cooling and water-cooling, and it was found that at the same temperature, water cooling treatment was more likely to cause microcracks and pores, which can cause more serious damage to the quartz sandstone. These results confirm that different cooling methods have different effects on the physical and mechanical properties of quartz sandstone, and provide a basis for the stability prediction of rock mass engineering such as tunnel suffering from fire.


Sign in / Sign up

Export Citation Format

Share Document