ASPECT RATIO EFFECTS ON BOTTOM HEATED 2D CAVITY USING ENERGY STREAMLINES AND FIELD SYNERGY PRINCIPLE

2019 ◽  
Vol 50 (1) ◽  
pp. 41-46
Author(s):  
Hari Ponnamma Rani ◽  
Narayana Vekamulla ◽  
Yadagiri Rameshwar ◽  
Sergey Vladimirovich Starchenko

In the present work free convective air flow in the two-dimensional cavity with three different aspect ratios (AR) are investigated using direct numerical simulation. The bottom wall is assumed to be kept at a uniform higher temperature than that of the top wall and the other two vertical walls are assumed to be thermally insulated. The computations are conducted for Rayleigh number (Ra) values from 103 to 106. Convective schemes are compared and Self Filtered Central Differencing Scheme is used to discretize convective term. Parallel computing MPI code is adapted to run the simulations. An attempt has been made to gather the visualization techniques such as streamlines, isotherms, energy streamlines and field synergy principle to analyse the flow behaviour inside the cavity. When Ra is small, the vertical energy streamlines are observed in the cavity. As Ra further increased, the free energy streamlines observed at the boundary and the trapped energy streamlines at the centre in the horizontal direction. For a fixed Ra, and increasing AR, the average synergy angle increases. This indicates synergy or the coordination between velocity magnitude and temperature field gets decreased and leads to the growth of heat transfer rate. The field synergy principle implies by enhancing the synergy between the velocity vector and temperature gradient.

Author(s):  
Vekamulla Narayana

In the present study, an attempt is made to explore the flow field inside the differentially heated lid-driven square cavity. The governing equations along with boundary conditions are solved numerically. The simulated results (100 ≤ Re ≤ 1000 and 0.001 ≤ Ri ≤ 10) are validated with previous results in the literature. The convection differencing schemes, namely, UPWIND, QUICK, SUPERBEE, and SFCD, are discussed and are used to simulate the flow using the MPI code. It is observed that the computational cost for all the differencing schemes get reduced tremendously when the MPI code is implemented. Plots demonstrate the influences of Re and Ri in terms of the contours of the fluid streamlines, isotherms, energy streamlines, and field synergy principle.


2013 ◽  
Vol 315 ◽  
pp. 433-437
Author(s):  
Nor Azwadi Che Sidik ◽  
Arman Safdari

This paper presents numerical investigations of the thermal and fluid flow behavior in an L-shaped of cavity filled with nanofluid. The left and bottom walls are heated to higher temperature than the horizontal upper and right vertical walls. The results show that the characteristic of flow and heat transfer are critically dependent on the dimensionless Rayleigh number. We also found that the presence of nanoparticle enhances the heat transfer rate in the enclosure.


2013 ◽  
Vol 773 ◽  
pp. 561-565 ◽  
Author(s):  
Long Yu ◽  
Shu Rong Yu ◽  
Chun Ling Li

According to field synergy principle, analyzes the relationship of the effect for heat transfer with mass transfer in porous media. Using the divergence equation, express the degree of gas phase velocity vector and temperature gradient velocity in the process of heat and mass transfer, and the field synergy angleθplay an important role in heat and mass transfer either global or partial. In the result, the heat and mass transfer would be constrained by each other whileπθ>π/2, and be promoted whileπ/2>θ0, and be independency whileθ=π/2. The divergence equation of field synergy principle present the method of strengthen the heat and mass transfer in porous media.


Processes ◽  
2021 ◽  
Vol 9 (5) ◽  
pp. 786
Author(s):  
Jiedong Ye ◽  
Junshuai Lv ◽  
Dongli Tan ◽  
Zhiqiang Ai ◽  
Zhiqiang Feng

The NH3 uniformity and conversion rate produced by the urea–water solution spray system is an essential factor affecting de-NOx efficiency. In this work, a three-dimensional simulation model was developed with the CFD software and was employed to investigate the effects of two typical injection methods (wall injection and center injection) and three distribution strategies (pre-mixer, post-mixer, pre-mixer, and post-mixer) of two typical mixers on the urea conversion rate and uniformity. The field synergy principle was employed to analyze the heat transfer of different mixer flow fields. The results show that the single mixer has instability in optimizing different injection positions due to different injection methods and injection positions. The dual-mixer is stable in the optimization of the flow field under different conditions. The conclusion of the field synergy theory of the single mixer accords with the simulation result. The Fc of the dual-mixer cases is low, but the NH3 conversion and uniformity index rate are also improved due to the increase in the residence time of UWS.


2009 ◽  
Vol 131 (5) ◽  
Author(s):  
Wenjiang Wu ◽  
Chan Y. Ching

The effect of the top wall temperature on the laminar natural convection in air-filled rectangular cavities driven by a temperature difference across the vertical walls was investigated for three different aspect ratios of 0.5, 1.0, and 2.0. The temperature distributions along the heated vertical wall were measured, and the flow patterns in the cavities were visualized. The experiments were performed for a global Grashof number of approximately 1.8×108 and nondimensional top wall temperatures from 0.52 (insulated) to 1.42. As the top wall was heated, the flow separated from the top wall with an undulating flow region in the corner of the cavity, which resulted in a nonuniformity in the temperature profiles in this region. The location and extent of the undulation in the flow are primarily determined by the top wall temperature and nearly independent of the aspect ratio of the cavity. The local Nusselt number was correlated with the local Rayleigh number for all three cavities in the form of Nu=C⋅Ran, but the values of the constants C and n changed with the aspect ratio.


2018 ◽  
Vol 55 (3) ◽  
pp. 811-822 ◽  
Author(s):  
Jun Shen ◽  
Lingping Zeng ◽  
Zhichun Liu ◽  
Wei Liu

Sign in / Sign up

Export Citation Format

Share Document