Mass Transfer Enhancement for CO2 Absorption in Structured Packed Absorption Column

2019 ◽  
Vol 41 (5) ◽  
pp. 820-820
Author(s):  
Pongayi Ponnusamy Selvi and Rajoo Baskar Pongayi Ponnusamy Selvi and Rajoo Baskar
Keyword(s):  
Mass Transfer ◽  
Transfer Coefficient ◽  
Mass Transfer Coefficient ◽  
Gas Flow ◽  
Aqueous Ammonia ◽  
Volume Flow Rate ◽  
Packed Column ◽  
Operating Conditions ◽  
Co2 Absorption ◽  
Absorption Column

The acidic gas, Carbon dioxide (CO2) absorption in aqueous ammonia solvent was carried as an example for industrial gaseous treatment. The packed column was provided with a novel structured BX-DX packing material. The overall mass transfer coefficient was calculated from the absorption efficiency of the various runs. Due to the high solubility of CO2, mass transfer was shown to be mainly controlled by gas side transfer rates. The effects of different operating parameters on KGav including CO2 partial pressure, total gas flow rates, volume flow rate of aqueous ammonia solution, aqueous ammonia concentration, and reaction temperature were investigated. For a particular system and operating conditions structured packing provides higher mass transfer coefficient than that of commercial random packing.

scholarly journals Mass Transfer in Multiphasic Gas/Liquid/Liquid Systems. KLa Determination Using the Effectiveness-Number of Transfer Unit Method

Processes ◽  
2018 ◽  
Vol 6 (9) ◽  
pp. 156 ◽  
Author(s):  
Éric Dumont
Keyword(s):  
Mass Transfer ◽  
Transfer Coefficient ◽  
Mass Transfer Coefficient ◽  
Flow Rate ◽  
Gas Flow ◽  
Absorption Capacity ◽  
Operating Conditions ◽  
Transfer Unit ◽  
Liquid Systems ◽  
Overall Mass Transfer Coefficient

The Effectiveness-Number of Transfer Unit method (ε-NTU method) was applied to determine the overall mass transfer coefficient, KLa, of operating gas-liquid absorbers treating Volatile Organic Compounds (VOCs). This method requires the knowledge of the operating conditions (gas flow rate, QG; liquid flow rate, QL; scrubber volume V), the measurement of gaseous concentrations at the inlet, CGin, and at the outlet, CGout, of the contactor (in order to determine the effectiveness of the absorber ε) and the calculation of the Henry coefficient of the VOC between the gas and the liquid phases (HVOC). Coupled with the “equivalent absorption capacity” concept, the ε-NTU method was used to determine KLa of absorbers contacting a gas and a mixture of water and a Non Aqueous Phase, successfully. The method, validated from literature data for configurations countercurrent scrubbers and stirred tank reactors, could be used to simply determine the overall mass transfer coefficient of systems for which the standard KLa determination methods still remain non-reliable or inaccurate (viscous solvents, mixture of immiscible liquids, fermentation broths…).

scholarly journals Mass Transfer Performance Study for CO2 Absorption into Non-Precipitated Potassium Carbonate Promoted with Glycine Using Packed Absorption Column

2020 ◽  
Vol 12 (9) ◽  
pp. 3873
Author(s):  
Nur Farhana Ajua Mustafa ◽  
Azmi Mohd Shariff ◽  
Wee Horng Tay ◽  
Hairul Nazirah Abdul Halim ◽  
Siti Munirah Mhd Yusof
Keyword(s):  
Mass Transfer ◽  
Transfer Coefficient ◽  
Mass Transfer Coefficient ◽  
Removal Efficiency ◽  
Potassium Carbonate ◽  
Elevated Pressure ◽  
Co2 Removal ◽  
Co2 Absorption ◽  
Absorption Column ◽  
Co2 Removal Efficiency

The removal of carbon dioxide (CO2) at offshore operation requires an absorption system with an environmentally friendly solvent that can operate at elevated pressure. Potassium carbonate promoted with glycine, PCGLY, is a green solvent that has potential for offshore applications. For high solvent concentrations at elevated pressure, the by-product of CO2 absorption consists of precipitates that increase operational difficulty. Therefore, this study was done to assess the CO2 absorption performance of non-precipitated PCGLY with concentration 15wt%PC+3wt%GLY, which is known to have comparable solubility performance with MDEA. A packed absorption column was used to identify the CO2 removal efficiency, mass transfer coefficient in liquid film, k l a e , and overall volumetric mass transfer coefficient, K G a v . A simplified rate-based model was used to determine k l a e and K G a v based on the experimental data with a maximum MAE value, 0.057. The results showed that liquid flow rates and liquid temperature gives significant effects on the k l a e and K G a v profile, whereas gas flow rate and operating pressure had little effect. The CO2 removal efficiency of PCGLY was found to be 77%, which was only 2% lower than 1.2 kmol/m3 MDEA. K G a v of PCGLY is comparable with MDEA. The absorption process using PCGLY shows potential in the CO2 sweetening process at offshore.

scholarly journals Carbon Dioxide Absorption in a Fabricated Wetted-Wall Column Using Varying Concentrations of Aqueous Ammonia

2014 ◽  
Vol 13 (2) ◽  
pp. 9
Author(s):  
H.E.E. Ching ◽  
L.M.P. Co ◽  
S.I.C. Tan ◽  
S.A. Roces ◽  
N.P. Dugos ◽  
...  
Keyword(s):  
Mass Transfer ◽  
Steady State ◽  
Transfer Coefficient ◽  
Mass Transfer Coefficient ◽  
Flow Rate ◽  
Flue Gas ◽  
Carbon Capture ◽  
Aqueous Ammonia ◽  
Co2 Absorption ◽  
Wetted Wall Column

Due to the continued increasing levels of CO2 emissions that is contributing to climate change, CO2 mitigation technologies, particularly carbon capture and storage, are being developed to address the goal of abating CO2 levels. Carbon capture technologies can be applied at the pre-combustion, oxy-fuel combustion, and post-combustion stages, the latter being the most widely used due to its flexibility. Among the several CO2 separation processes available for carbon capture, absorption is the most widely used where amine solutions are used as absorbents. This paper highlights the use of a wetted wall column fabricated by Siy and Villanueva (2012) and simulated flue gas to determine the performance of CO2 absorption in terms of the percentage of CO2 absorbed, the steady state time, and the overall gas mass transfer coefficient. The concentrations used were 1, 5, 10, and 15% NH3(aq) at a constant temperature range of 12-17ºC, solvent flow rate of 100 mL/min, and simulated flue gas flow rate of 2 L/min. It was found that increasing the solvent concentration resulted in a proportional increase both in the percentage of CO2 absorbed and the overall gas mass transfer coefficient. The average percentage of CO2 absorbed ranged within 52.25% to 95.29% while the overall mass transfer coefficient ranged from 0.1843 to 0.7746 mmol/m2∙s∙kPa. However, erratic behavior was seen for the time required for the system to reach steady state. Using Design ExpertTM for analysis, the results showed that the effect of varying the concentration had a significant effect on the percentage of CO2 absorbed and the overall gas mass transfer coefficient. The results proved that the greater the aqueous ammonia concentration, the greater the percentage of CO2 absorbed. The range of 5-10% aqueous ammonia is recommended because the percentage of CO2 absorbed peaks at an average of 92% beyond the range of 5-10%.

scholarly journals Effects of geometric parameters on volumetric mass transfer coefficient of non-Newtonian fluids in stirred tanks

2021 ◽  
Vol 0 (0) ◽  
Author(s):  
Haider Ali ◽  
Sofia Zhu ◽  
Jannike Solsvik
Keyword(s):  
Mass Transfer ◽  
Transfer Coefficient ◽  
Mass Transfer Coefficient ◽  
Gas Flow ◽  
Scale Up ◽  
Pilot Scale ◽  
Operating Conditions ◽  
Volumetric Mass Transfer Coefficient ◽  
Transfer Coefficients ◽  
Stirred Tanks

Abstract Scaling up stirred tanks is a significant challenge because of the research gaps between laboratory and industrial-scale setups. It is necessary to understand the effects of scale-up on the mass transfer in stirred tanks, and this requires meticulous experimental analysis. The present study investigates the effects of tank size and aspect ratio ( H L T ${H}_{L}}{T}$ ) on the volumetric mass transfer coefficients of shear-thinning fluids. The experiments were conducted in three stirred tanks of different sizes (laboratory and pilot scale) and geometries (standard and nonstandard). H L T ${H}_{L}}{T}$ was 1 for the standard tanks and 3.5 for the nonstandard stirred tanks. Three sizes of stirred tanks were used: 11 L with H L T ${H}_{L}}{T}$ of 1, 40 L with H L T ${H}_{L}}{T}$ of 3.5, and 47 L with H L T ${H}_{L}}{T}$ of 1. Impeller stirring speeds and gas flow rates were in the range of 800–900 rev min−1 and 8–10 L min−1, respectively. The volumetric mass transfer coefficient was estimated based on the dissolved oxygen concentration in the fluids, and the effects of rheology and operating conditions on the volumetric mass transfer coefficient were observed. The volumetric mass transfer coefficient decreased as tank size increased and increased with an increase in operating conditions, but these effects were also clearly influenced by fluid rheology. The impacts of scale-up and operating conditions on the volumetric mass transfer coefficient decreased as liquid viscosity increased.

scholarly journals Optimization in the Absorption and Desorption of CO2 Using Sodium Glycinate Solution

2018 ◽  
Vol 8 (11) ◽  
pp. 2041 ◽  
Author(s):  
Pao Chi Chen ◽  
Sheng-Zhong Lin
Keyword(s):  
Mass Transfer ◽  
Transfer Coefficient ◽  
Mass Transfer Coefficient ◽  
Flow Rate ◽  
Bubble Column ◽  
Absorption Efficiency ◽  
Operating Conditions ◽  
Flow Rate Ratio ◽  
Optimum Operating ◽  
Co2 Absorption

This study used sodium glycinate as an absorbent to absorb CO2 in the bubble column scrubber under constant pH and temperature environments to obtain the operating range, CO2 loading, and mass transfer coefficient. For efficient experimentation, the Taguchi method is used for the experimental design. The process parameters are the pH, gas flow rate (Qg), liquid temperature (T), and absorbent concentration (CL). The effects of the parameters on the absorption efficiency, absorption rate, overall mass transfer coefficient, gas–liquid molar flow rate ratio, CO2 loading, and absorption factor are to be explored. The optimum operating conditions and the order of parameter importance are obtained using the signal/noise (S/N) ratio analysis, and the optimum operating conditions are further verified. The verification of the optimum values was also carried out. The order of parameter importance is pH > CL > Qg > T. Evidence in the 13CNMR (Carbon 13 Nuclear Magnetic Resonance) spectra shows that the pH value has an effect on the solution composition, which affects both the absorption efficiency and mass transfer coefficient. There are 18 experiments for regeneration, where the operating temperature is 100–120 °C. The heat of regeneration was measured according to the thermodynamic data. The CO2 loading, the overall mass transfer, and the heats of regeneration correlation are also discussed in this work. Finally, an operating policy for the CO2 absorption process was confirmed.

scholarly journals Effect of pH and Gas Flow Rate on Ozone Mass Transfer of Κ-Carrageenan Solution in Bubble Column Reactor

REAKTOR ◽  
2019 ◽  
Vol 18 (04) ◽  
pp. 177 ◽  
Author(s):  
Aji Prasetyaningrum ◽  
Dyah Arum Kusumaningtyas ◽  
Purbo Suseno ◽  
Ratnawati Ratnawati
Keyword(s):  
Mass Transfer ◽  
Transfer Coefficient ◽  
Mass Transfer Coefficient ◽  
Flow Rate ◽  
Gas Flow ◽  
Bubble Column ◽  
Operating Conditions ◽  
Bubble Column Reactor ◽  
Gas Flow Rate ◽  
Column Reactor

This research was conducted to calculate the mass transfer coefficient value for ozonation reaction of κ-carrageenan solution in the bubble column reactor. Ozone gas was produced using ozone generator type corona discharge. In this study, operating conditions were regulated at ozone gas flow rate 2- 5 L min-1, pH 4-10, and temperature 29 ± 1 oC. Samples were tested every 5 minutes to determine the dissolved ozone concentration. The results showed that dissolved ozone concentrations increased with increasing ozonation time and ozone gas flow rate. However, a very high gas flow rate can increase turbulence so that the mass transfer coefficient (kLa) value decreased. In alkaline conditions, the formation of free radicals (HO*) increases so that the amount of dissolved ozone decreases. The kLa value of ozone gas in κ-carrageenan solution is slightly lower than the kLa value of the ozone gas in the water. The results of this study indicate that (kLa) ozone gas in water is 0.131 / minute while the value (kLa) in κ-carrageenan solution is 0.128 / minute.

Mass Transfer Coefficients during Steel Decarburization in a RH Degasser

2008 ◽  
Vol 273-276 ◽  
pp. 679-684
Author(s):  
Roberto Parreiras Tavares ◽  
André Afonso Nascimento ◽  
Henrique Loures Vale Pujatti
Keyword(s):  
Mass Transfer ◽  
Reynolds Number ◽  
Transfer Coefficient ◽  
Mass Transfer Coefficient ◽  
Gas Flow ◽  
Vacuum Chamber ◽  
Volumetric Mass Transfer Coefficient ◽  
Gas Flow Rate ◽  
Rh Process ◽  
Kinetics Of

The RH process is a secondary refining process that can simultaneously attain significant levels of removal of interstitial elements, such as carbon, nitrogen and hydrogen, from liquid steel. In the RH process, the decarburization rate plays a very important role in determining the productivity of the equipment. The kinetics of this reaction is controlled by mass transfer in the liquid phase. In the present work, a physical model of a RH degasser has been built and used in the study of the kinetics of decarburization. The effects of the gas flow rate and of the configurations of the nozzles used in the injection of the gas have been analyzed. The decarburization reaction of liquid steel was simulated using a reaction involving CO2 and caustic solutions. The concentration of CO2 in the solution was evaluated using pH measurements. Based on the experimental results, it was possible to estimate the reaction rate constant. A volumetric mass transfer coefficient was then calculated based on these rate constants and on the circulation rate of the liquid. The logarithm of the mass transfer coefficient showed a linear relationship with the logarithm of the gas flow rate. The slope of the line was found to vary according to the relevance of the reaction at the free surface in the vacuum chamber. A linear relationship between the volumetric mass transfer coefficient and the nozzle Reynolds number was also observed. The slopes of the lines changed according to the relative importance of the two reaction sites, gas-liquid interface in the upleg snorkel and in the vacuum. At higher Reynolds number, the reaction in the vacuum chamber tends to be more significant.

Influence of Gas-Liquid Distribution Inducer on Mass Transfer Coefficient in Rotating Packed Bed

2014 ◽  
Vol 908 ◽  
pp. 277-281
Author(s):  
Fei Wu ◽  
Jie Wu ◽  
Mei Jin ◽  
Fang Wang ◽  
Ping Lu
Keyword(s):  
Mass Transfer ◽  
Transfer Coefficient ◽  
Mass Transfer Coefficient ◽  
Flow Rate ◽  
Rotor Blade ◽  
Gas Flow ◽  
Packed Bed ◽  
Contact Length ◽  
Liquid Distribution ◽  
Rotating Packed Bed

Based on acetone-H2O system, the influence of the gas-liquid distribution inducer on the mass transfer coefficient in the rotating packed bed with the stainless steel packing was investigated. Furthermore, the absorption performance was also obtained under the experimental condition of the rotational speed of 630 rpm, the gas flow rate of 2 m3/h and the liquid flow rate of 100 L/h in the rotating packed bed with different types and different installation ways of the distribution inducer. The experimental results showed that the volumetric mass transfer coefficient Kyα per unit contact length of gas-liquid was increased by 8.6% for the forward-curved fixed blade, by 19.8% for the backward-curved rotor blade and by 33.2% with the combination of the straight radial rotor blade and the backward-curved fixed blade, respectively. Furthermore, when the gas flow rate was 2.5 m3/h, Kyα per unit contact length of gas-liquid was increased by 2.9% for the forward-curved fixed blade, by 25.3% for the backward-curved rotor blade, by 42.7% for the combination of the straight radial rotor blade and the backward-curved fixed blade, respectively. The results indicated that the distribution inducer play an important role on the improvement of the mass transfer coefficient in acetone-H2O system.

Effect of bubble contamination on gas–liquid mass transfer coefficient on CO2 absorption in amine solutions

2008 ◽  
Vol 137 (2) ◽  
pp. 422-427 ◽  
Author(s):  
Rocío Maceiras ◽  
Sebastião S. Alves ◽  
M. Ángeles Cancela ◽  
Estrella Álvarez
Keyword(s):  
Mass Transfer ◽  
Transfer Coefficient ◽  
Mass Transfer Coefficient ◽  
Co2 Absorption ◽  
Liquid Mass ◽  
Liquid Mass Transfer ◽  
Amine Solutions
Sign in / Sign up

Export Citation Format

Share Document