scholarly journals Reconfiguration of 3 MV Marx Generator into a Modern High Efficiency System

2017 ◽  
Author(s):  
Joni Klüss ◽  
William Larzelere
Keyword(s):  
High Voltage ◽  
High Efficiency ◽  
Marx Generator ◽  
Mississippi State University ◽  
State University ◽  
Labor Costs ◽  
Functional Elements ◽  
Generator System ◽  
Impulse Generator

<p>High voltage impulse generators are intended to last for long periods of time. Upon reaching the end of their technical lifetime, decisions concerning decommissioning, replacement, refurbishment or upgrading are needed. A new generator is a considerable investment. Significant reductions in material and labor costs can be made by repurposing still functional elements of the existing generator and redesigning the circuit for higher efficiency requiring fewer components. This paper describes the process of refurbishing the Mississippi State University (MSU) High Voltage Laboratory 3 MV, 56 kJ impulse generator originally built in 1962 into a modern digital impulse generator system. </p>

scholarly journals Portable DC Supply Based on SiC Power Devices for High-Voltage Marx Generator

Electronics ◽  
2021 ◽  
Vol 10 (3) ◽  
pp. 313
Author(s):  
Jacek Rąbkowski ◽  
Andrzej Łasica ◽  
Mariusz Zdanowski ◽  
Grzegorz Wrona ◽  
Jacek Starzyński
Keyword(s):  
High Voltage ◽  
Specific Area ◽  
Input Voltage ◽  
Marx Generator ◽  
Power Devices ◽  
Laboratory Setup ◽  
High Voltage Gain ◽  
Main Components ◽  
Two Stages ◽  
Very High

The paper describes major issues related to the design of a portable SiC-based DC supply developed for evaluation of a high-voltage Marx generator. This generator is developed to be a part of an electromagnetic cannon providing very high voltage and current pulses aiming at the destruction of electronics equipment in a specific area. The portable DC supply offers a very high voltage gain: input voltage is 24 V, while the generator requires supply voltages up to 50 kV. Thus, the system contains two stages designed on the basis of SiC power devices operating with frequencies up to 100 kHz. At first, the input voltage is boosted up to 400 V by a non-isolated double-boost converter, and then a resonant DC-DC converter with a special transformer elevates the voltage to the required level. In the paper, the main components of the laboratory setup are presented, and experimental results of the DC supply and whole system are also shown.

scholarly journals Novel High-Efficiency High Step-Up DC–DC Converter with Soft Switching and Low Component Voltage Stress for Photovoltaic System

Processes ◽  
2021 ◽  
Vol 9 (7) ◽  
pp. 1112
Author(s):  
Yu-En Wu ◽  
Jyun-Wei Wang
Keyword(s):  
High Voltage ◽  
Output Voltage ◽  
High Efficiency ◽  
Low Voltage ◽  
Leakage Inductance ◽  
Power Switch ◽  
Half Wave Voltage ◽  
Half Wave ◽  
Voltage Stress ◽  
Voltage Doubler

This study developed a novel, high-efficiency, high step-up DC–DC converter for photovoltaic (PV) systems. The converter can step-up the low output voltage of PV modules to the voltage level of the inverter and is used to feed into the grid. The converter can achieve a high step-up voltage through its architecture consisting of a three-winding coupled inductor common iron core on the low-voltage side and a half-wave voltage doubler circuit on the high-voltage side. The leakage inductance energy generated by the coupling inductor during the conversion process can be recovered by the capacitor on the low-voltage side to reduce the voltage surge on the power switch, which gives the power switch of the circuit a soft-switching effect. In addition, the half-wave voltage doubler circuit on the high-voltage side can recover the leakage inductance energy of the tertiary side and increase the output voltage. The advantages of the circuit are low loss, high efficiency, high conversion ratio, and low component voltage stress. Finally, a 500-W high step-up converter was experimentally tested to verify the feasibility and practicability of the proposed architecture. The results revealed that the highest efficiency of the circuit is 98%.

scholarly journals Non-Destructive Lumber and Engineered Pine Products Research in the Gulf South U.S. 2005–2020

Forests ◽  
2021 ◽  
Vol 12 (1) ◽  
pp. 91
Author(s):  
R. Dan Seale ◽  
Rubin Shmulsky ◽  
Frederico Jose Nistal Franca
Keyword(s):  
Agricultural Research ◽  
Forest Products ◽  
Wood Products ◽  
Time Interval ◽  
Mississippi State University ◽  
State University ◽  
White Oak ◽  
Department Of Agriculture ◽  
Mass Timber ◽  
Structural Lumber

This review primarily describes nondestructive evaluation (NDE) work at Mississippi State University during the 2005–2020 time interval. Overall, NDE is becoming increasingly important as a means of maximizing and optimizing the value (economic, engineering, utilitarian, etc.) of every tree that comes from the forest. For the most part, it focuses on southern pine structural lumber, but other species such as red pine, spruce, Douglas fir, red oak, and white oak and other products such as engineered composites, mass timber, non-structural lumber, and others are included where appropriate. Much of the work has been completed in conjunction with the U.S. Department of Agriculture, Forest Service, Forest Products Laboratory as well as the Agricultural Research Service with the overall intent of improving lumber and wood products standards and valuation. To increase the future impacts and adoption of this NDE-related work, wherever possible graduate students have contributed to the research. As such, a stream of trained professionals is a secondary output of these works though it is not specifically detailed herein.

Development of cooperative industrial education at Mississippi State University

1986 ◽  
Vol 63 (3) ◽  
pp. 235
Author(s):  
Eugene Grimley ◽  
Leon L. Combs ◽  
Charles U. Pittman
Keyword(s):  
Mississippi State University ◽  
State University ◽  
Industrial Education

scholarly journals Measurement of Ozone Production Sensor

2010 ◽  
Vol 3 (3) ◽  
pp. 545-555 ◽  
Author(s):  
M. Cazorla ◽  
W. H. Brune
Keyword(s):  
Production Rate ◽  
High Efficiency ◽  
Ambient Air ◽  
Ozone Production ◽  
State University ◽  
Photostationary State ◽  
Sample Chamber ◽  
Efficiency Conversion ◽  
The Difference ◽  
Teflon Film

Abstract. A new ambient air monitor, the Measurement of Ozone Production Sensor (MOPS), measures directly the rate of ozone production in the atmosphere. The sensor consists of two 11.3 L environmental chambers made of UV-transmitting Teflon film, a unit to convert NO2 to O3, and a modified ozone monitor. In the sample chamber, flowing ambient air is exposed to the sunlight so that ozone is produced just as it is in the atmosphere. In the second chamber, called the reference chamber, a UV-blocking film over the Teflon film prevents ozone formation but allows other processes to occur as they do in the sample chamber. The air flows that exit the two chambers are sampled by an ozone monitor operating in differential mode so that the difference between the two ozone signals, divided by the exposure time in the chambers, gives the ozone production rate. High-efficiency conversion of NO2 to O3 prior to detection in the ozone monitor accounts for differences in the NOx photostationary state that can occur in the two chambers. The MOPS measures the ozone production rate, but with the addition of NO to the sampled air flow, the MOPS can be used to study the sensitivity of ozone production to NO. Preliminary studies with the MOPS on the campus of the Pennsylvania State University show the potential of this new technique.

Sign in / Sign up

Export Citation Format

Share Document