scholarly journals Ancillary Services in Honduras, Regulatory Framework and Proposals for Its Development in the System

2019 ◽  
Vol 7 (1) ◽  
pp. 36-44
Author(s):  
Jorge Andrés Pérez ◽  
Ellis Moisés Reyes ◽  
Tannia Karina Vindel
Keyword(s):  
Power Systems ◽  
Power System ◽  
Large Scale ◽  
Frequency Control ◽  
Regulatory Framework ◽  
Ancillary Services ◽  
Electricity Sector ◽  
Control Voltage ◽  
The Stability ◽  
Power Systems Operation

The ancillary services are essential in the power Systems operation, historically this services haven’t been regulated in any way in Honduras. There have been changes recently into the regulatory framework in the entire electricity sector alongside the large-scale injection of photovoltaic and wind powered centrals in the System. Considering these scenarios, the ancillary services become a necessity in terms of the operation for the power system and the stability associated with it. In this paper, we analyze the technical and economic aspects related to the frequency control, voltage control and blackstart services, we compare the services provided in different countries and how it is possible to adapt the successful cases to the Honduran power system.

scholarly journals Frequency Control of Large-Scale Interconnected Power Systems via Battery Integration: A Comparison Between the Hybrid Battery Model and WECC Model

2021 ◽  
Author(s):  
Roghieh Abdollahi Biroon ◽  
Pierluigi Pisu ◽  
David Schoenwald
Keyword(s):  
Power Systems ◽  
Power System ◽  
Large Scale ◽  
System Analysis ◽  
Hybrid Control ◽  
Frequency Control ◽  
Renewable Energy Sources ◽  
Control Design ◽  
Energy Sources ◽  
The Stability

The increasing penetration of renewable energy sources in power grids highlights the role of battery energy stor- age systems (BESSs) in enhancing the stability and reliability of electricity. A key challenge with the renewables’, specially the BESSs, integration into the power system is the lack of proper dynamic model for stability analysis. Moreover, a proper control design for the power system is a complicated issue due to its complexity and inter-connectivity. Thus, the application of decentralized control to improve the stability of a large- scale power system is inevitable, especially in distributed energy sources (DERs). This paper presents an optimal distributed hybrid control design for the interconnected systems to suppress the effects of small disturbances in the power system employing utility-scale batteries based on existing battery models. The results show that i) the smart scheduling of the batteries’ output reduces the inter-area oscillations and improves the stability of the power systems; ii) the hybrid model of the battery is more user-friendly compared to the Western electricity coordinating council (WECC) model in power system analysis.

scholarly journals Frequency Control of Large-Scale Interconnected Power Systems via Battery Integration: A Comparison between the Hybrid Battery Model and WECC Model

Energies ◽  
2021 ◽  
Vol 14 (18) ◽  
pp. 5605
Author(s):  
Roghieh Abdollahi Biroon ◽  
Pierluigi Pisu ◽  
David Schoenwald
Keyword(s):  
Power Systems ◽  
Power System ◽  
Distributed Control ◽  
Hybrid Model ◽  
Large Scale ◽  
Dynamic Models ◽  
Frequency Control ◽  
Renewable Energy Sources ◽  
Control Design ◽  
The Stability

The increasing penetration of renewable energy sources in power grids highlights the role of battery energy storage systems (BESSs) in enhancing the stability and reliability of electricity. A key challenge with the renewables’, specially the BESSs, integration into the power system is the lack of proper dynamic models and their application in power system analyses. The control design strategy mainly depends on the system dynamics which underlines the importance of the system accurate dynamic modeling. Moreover, control design for the power system is a complicated issue due to its complexity and inter-connectivity, which makes the application of distributed control to improve the stability of a large-scale power system inevitable. This paper presents an optimal distributed control design for the interconnected systems to suppress the effects of small disturbances in the power system employing utility-scale batteries based on existing battery models. The control strategy is applied to two dynamic models of the battery: hybrid model and Western electricity coordinating council (WECC) model. The results show that (i) the smart scheduling of the batteries’ output reduces the inter-area oscillations and improves the stability of the power systems; (ii) the hybrid model of the battery is more user-friendly compared to the WECC model in power system analyses.

scholarly journals Evaluating the Potential Contribution of District Heating to the Flexibility of the Future Italian Power System

Energies ◽  
2022 ◽  
Vol 15 (2) ◽  
pp. 584
Author(s):  
Chiara Magni ◽  
Sylvain Quoilin ◽  
Alessia Arteconi
Keyword(s):  
Power Systems ◽  
Power System ◽  
Large Scale ◽  
District Heating ◽  
Energy System ◽  
Heat Pumps ◽  
Electricity Sector ◽  
Potential Contribution ◽  
The Future ◽  
Promising Solution

Flexibility is crucial to enable the penetration of high shares of renewables in the power system while ensuring the security and affordability of the electricity dispatch. In this regard, heat–electricity sector coupling technologies are considered a promising solution for the integration of flexible devices such as thermal storage units and heat pumps. The deployment of these devices would also enable the decarbonization of the heating sector, responsible for around half of the energy consumption in the EU, of which 75% is currently supplied by fossil fuels. This paper investigates in which measure the diffusion of district heating (DH) coupled with thermal energy storage (TES) units can contribute to the overall system flexibility and to the provision of operating reserves for energy systems with high renewable penetration. The deployment of two different DH supply technologies, namely combined heat and power units (CHP) and large-scale heat pumps (P2HT), is modeled and compared in terms of performance. The case study analyzed is the future Italian energy system, which is simulated through the unit commitment and optimal dispatch model Dispa-SET. Results show that DH coupled with heat pumps and CHP units could enable both costs and emissions related to the heat–electricity sector to be reduced by up to 50%. DH systems also proved to be a promising solution to grant the flexibility and resilience of power systems with high shares of renewables by significantly reducing the curtailment of renewables and cost-optimally providing up to 15% of the total upward reserve requirements.

scholarly journals Adaptive Integral Second-Order Sliding Mode Control Design for Load Frequency Control of Large-Scale Power System with Communication Delays

Complexity ◽  
2021 ◽  
Vol 2021 ◽  
pp. 1-19
Author(s):  
Anh-Tuan Tran ◽  
Bui Le Ngoc Minh ◽  
Phong Thanh Tran ◽  
Van Van Huynh ◽  
Van-Duc Phan ◽  
...  
Keyword(s):  
Sliding Mode Control ◽  
Power Systems ◽  
Power System ◽  
System Performance ◽  
Large Scale ◽  
Sliding Mode ◽  
Frequency Control ◽  
Load Frequency Control ◽  
Communication Delays ◽  
Second Order Sliding Mode

Nowadays, the power systems are getting more and more complicated because of the delays introduced by the communication networks. The existence of the delays usually leads to the degradation and/or instability of power system performance. On account of this point, the traditional load frequency control (LFC) approach for power system sketches a destabilizing impact and an unacceptable system performance. Therefore, this paper proposes a new LFC based on adaptive integral second-order sliding mode control (AISOSMC) approach for the large-scale power system with communication delays (LSPSwCD). First, a new linear matrix inequality is derived to ensure the stability of whole power systems using Lyapunov stability theory. Second, an AISOSMC law is designed to ensure the finite time reachability of the system states. To the best of our knowledge, this is the first time the AISOSMC is designed for LFC of the LSPSwCD. In addition, the report of testing results presents that the suggested LFC based on AISOSMC can not only decrease effectively the frequency variation but also make successfully less in mount of power oscillation/fluctuation in tie-line exchange.

scholarly journals Load Frequency Control of Multi-Region Interconnected Power Systems with Wind Power and Electric Vehicles Based on Sliding Mode Control

Energies ◽  
2021 ◽  
Vol 14 (8) ◽  
pp. 2288
Author(s):  
Zhenghao Wang ◽  
Yonghui Liu ◽  
Zihao Yang ◽  
Wanhao Yang
Keyword(s):  
Power Systems ◽  
Power System ◽  
Wind Power ◽  
Electric Vehicles ◽  
Sliding Mode ◽  
Frequency Control ◽  
Load Frequency Control ◽  
Interconnected Power System ◽  
The Stability ◽  
Grid Operation

In recent years, wind power systems have been used extensively, which not only improve the efficiency of current conventional power generation systems, but also can save traditional fossil fuel resources. However, considering the instability of wind power, after being grid connected, it can easily cause an impact on the stability of the grid operation. Considering the above problems, this paper considers to make full use of the energy storage part of electric vehicles (EVs) to increase the stability of grid operation. Based on the mathematical model, this paper studies the load frequency control (LFC) problem of a multi-region interconnected power system with wind power and EVs. First, since the system states are difficult to be monitored, a state observer is designed to estimate the state. Based on this, the integral sliding mode controller (SMC) is designed to realize the LFC of the interconnected power system. Meanwhile, to obtain better control performance, this paper further analyzes and optimizes the controller parameters based on Lyapunov stability theory. At last, simulations are carried out for the power systems with two regions in Simulink. The results show that the designed controllers are effective to compensate the load demand disturbances. In addition, it is demonstrated that the battery storage of EVs can play the role of peak-shaving and valley-filling in LFC.

Microgrid modeling for contribution to the frequency control of power system

2021 ◽  
pp. 0309524X2110500
Author(s):  
Alireza Ghafouri
Keyword(s):  
Power Systems ◽  
Power System ◽  
Power Plants ◽  
Frequency Control ◽  
Stability Margin ◽  
Distributed Energy ◽  
Local Loads ◽  
Point Of Common Coupling ◽  
Common Coupling ◽  
The Stability

Recently, Distributed Energy Resources (DERs) are becoming more attractive to supply local loads under the concept of microgrids. These new parts of the power system have basically different dynamics compared with conventional power plants. Most of them are connected to the grid by power electronic interfaces, and their dynamic is determined by their controller. In this paper, the effect of the increased penetration of DERs on the load frequency problem of power systems is studied. The DERs of microgrids in each area are controlled to change their active power at Point of Common Coupling (PCC) after a disturbance in the power system. It is shown that with appropriate control of DERs in microgrids, the frequency deviation of the power system will decrease and the stability margin can be increased.

scholarly journals Distributed LQR Design for a Class of Large-Scale Multi-Area Power Systems

Energies ◽  
2019 ◽  
Vol 12 (14) ◽  
pp. 2664 ◽  
Author(s):  
Eleftherios Vlahakis ◽  
Leonidas Dritsas ◽  
George Halikias
Keyword(s):  
Power Systems ◽  
Power System ◽  
Large Scale ◽  
Convex Combination ◽  
Frequency Control ◽  
Linear Quadratic Regulator ◽  
Load Frequency Control ◽  
Linear Quadratic ◽  
Load Frequency ◽  
Power Load

Load frequency control (LFC) is one of the most challenging problems in multi-area power systems. In this paper, we consider power system formed of distinct control areas with identical dynamics which are interconnected via weak tie-lines. We then formulate a disturbance rejection problem of power-load step variations for the interconnected network system. We follow a top-down method to approximate a centralized linear quadratic regulator (LQR) optimal controller by a distributed scheme. Overall network stability is guaranteed via a stability test applied to a convex combination of Hurwitz matrices, the validity of which leads to stable network operation for a class of network topologies. The efficiency of the proposed distributed load frequency controller is illustrated via simulation studies involving a six-area power system and three interconnection schemes. In the study, apart from the nominal parameters, significant parametric variations have been considered in each area. The obtained results suggest that the proposed approach can be extended to the non-identical case.

The comparison and analysis of Type 3 wind turbine models used for researching the stability of electric power systems

2021 ◽  
Vol 0 (0) ◽  
Author(s):  
Igor Razzhivin ◽  
Aleksey Suvorov ◽  
Mikhail Andreev ◽  
Alisher Askarov
Keyword(s):  
Power Systems ◽  
Power System ◽  
Large Scale ◽  
Dynamic Properties ◽  
Renewable Energy Sources ◽  
Software Tools ◽  
Generic Models ◽  
Generator Type ◽  
The Stability ◽  
Type 3

Abstract The dominant trend of the modern energy is the use of generating plants based on renewable energy sources, among which the most common is a wind power plant based on doubly fed induction generator (Type 3 WT). The large-scale introduction of Type 3 WT into the modern power systems significantly changes their dynamic properties. There are problems with ensuring the basic condition of the reliability and the survivability of power systems – the stability. The study and solution of the indicated problems is possible only with the help of the mathematical modeling of a large-scale power systems which is currently being carried out with the help of widespread purely numerical software tools of calculations of modes and processes, which are characterized by various simplifications and limitations. For the properties and capabilities of software tools for studying stability issues, mathematical models of Type 3 WT, the so-called generic models, which also have simplifications and limitations, are adapted. In this article, the reliability of stability calculations of a real power system with Type 3 WT using software tools was evaluated, which allows to identify the influence of the applied simplifications and restrictions with a purely numerical approach on the quality of solving problems of assessing the stability of power systems with Type 3 WT. Also, the studies made it possible to identify the areas of the application of generic models of Type 3 WT as a part of the model of the real dimension power system, at which the greatest and least errors arise, as well as their causes. Such a comprehensive assessment becomes feasible due to the alternative approach proposed in the article, based on the use of a detail benchmark tool model instead of the full-scale data to compare the results of modeling.

scholarly journals A Comprehensive Review of the Cyber-Attacks and Cyber-Security on Load Frequency Control of Power Systems

Energies ◽  
2020 ◽  
Vol 13 (15) ◽  
pp. 3860
Author(s):  
Athira M. Mohan ◽  
Nader Meskin ◽  
Hasan Mehrjerdi
Keyword(s):  
Power Systems ◽  
Power System ◽  
Cyber Security ◽  
Distribution Systems ◽  
Frequency Control ◽  
Cyber Attacks ◽  
Load Frequency Control ◽  
Comprehensive Review ◽  
Load Frequency ◽  
The Stability

Power systems are complex systems that have great importance to socio-economic development due to the fact that the entire world relies on the electric network power supply for day-to-day life. Therefore, for the stable operation of power systems, several protection and control techniques are necessary. The power system controllers should have the ability to maintain power system stability. Three important quantities that should be effectively controlled to maintain the stability of power systems are frequency, rotor angle, and voltage. The voltage control in power systems maintains the voltage and reactive power within the required limits and the power factor control enhances the efficiency of power distribution systems by improving load power factors. Among various controls, the frequency control is the most time-consuming control mechanism of power systems due to the involvement of mechanical parts. As the control algorithms of frequency stabilization deliver control signals in the timescale of seconds, load frequency control (LFC) systems cannot handle complicated data validation algorithms, making them more vulnerable to disturbances and cyber-attacks. In addition, the LFC system has extended digital layers with open communication networks and is designed to operate with less human intervention. Moreover, the frequency fluctuation due to load change or cyber-attack in one area affects all other interconnected areas, and thus threatens the stability of the entire network. Due to these circumstances, research activities are still carried out in the field of frequency control and cyber-security. In this paper, a comprehensive review of the cyber-security of the LFC mechanism in the power system is presented. The highlights of the paper include the identification of attack points of different configurations of the LFC system, discussion of the attack strategies, formulation of various attack models, and a brief review of the existing detection and defense mechanisms against cyber-attacks on LFC.

scholarly journals Application of Battery Energy Storage Systems for Primary Frequency Control in Power Systems with High Renewable Energy Penetration

Energies ◽  
2021 ◽  
Vol 14 (5) ◽  
pp. 1379
Author(s):  
Md Ruhul Amin ◽  
Michael Negnevitsky ◽  
Evan Franklin ◽  
Kazi Saiful Alam ◽  
Seyed Behzad Naderi
Keyword(s):  
Renewable Energy ◽  
Power Systems ◽  
Power System ◽  
Storage Systems ◽  
Frequency Control ◽  
Battery Energy Storage ◽  
Battery Energy Storage Systems ◽  
Battery Energy ◽  
Primary Frequency ◽  
Primary Frequency Control

In power systems, high renewable energy penetration generally results in conventional synchronous generators being displaced. Hence, the power system inertia reduces, thus causing a larger frequency deviation when an imbalance between load and generation occurs, and thus potential system instability. The problem associated with this increase in the system’s dynamic response can be addressed by various means, for example, flywheels, supercapacitors, and battery energy storage systems (BESSs). This paper investigates the application of BESSs for primary frequency control in power systems with very high penetration of renewable energy, and consequently, low levels of synchronous generation. By re-creating a major Australian power system separation event and then subsequently simulating the event under low inertia conditions but with BESSs providing frequency support, it has been demonstrated that a droop-controlled BESS can greatly improve frequency response, producing both faster reaction and smaller frequency deviation. Furthermore, it is shown via detailed investigation how factors such as available battery capacity and droop coefficient impact the system frequency response characteristics, providing guidance on how best to mitigate the impact of future synchronous generator retirements. It is intended that this analysis could be beneficial in determining the optimal BESS capacity and droop value to manage the potential frequency stability risks for a future power system with high renewable energy penetrations.

Sign in / Sign up

Export Citation Format

Share Document