scholarly journals Response of low-rise buildings to moderate ground shaking, particularly the May 1990 Weber earthquake

1994 ◽  
Vol 27 (3) ◽  
pp. 205-221
Author(s):  
S. Sritharan ◽  
D. J. Dowrick
Keyword(s):  
New Zealand ◽  
Seismic Performance ◽  
Ground Motions ◽  
Time History ◽  
Imperial Valley ◽  
Ground Shaking ◽  
Moment Resisting Frames ◽  
Moment Resisting ◽  
Spectral Accelerations

In the Weber earthquake of 13 May 1990 the stronger component of the ground motions recorded in Dannevirke was similar in strength to the El Centro S00E record from the 1940 Imperial Valley earthquake which underlies the New Zealand loadings code, The Modified Mercalli intensity in Dannevirke however was only about MM7 1⁄2, whereas the intensity corresponding to the 1984 earthquake code is about MM8 1⁄2 for the Dannevirke area. This paper compares the strength of the Dannevirke record in terms of spectral accelerations with (i) the above El Centro record, (ii) the Matahina dam record of the 1987 Edgecumbe earthquake, and (iii) the loadings of the 1984 and 1992 New Zealand codes. Also described in the paper are time-history analyses of one- and two- storey buildings subjected to the above ground motions in an attempt to explain why the damage levels were lower than might be expected from the strength of the recorded accelerograms. Comparisons are made of the seismic performance of moment-resisting frames and walled structures. Comments are made on two of the provisions of the 1992 loadings code.

Amplified Seismic Loads in Steel Moment Frames

2016 ◽  
Vol 847 ◽  
pp. 222-232
Author(s):  
Bora Aksar ◽  
Selcuk Dogru ◽  
Bulent Akbas ◽  
Jay Shen ◽  
Onur Seker ◽  
...  
Keyword(s):  
Lateral Displacement ◽  
Ground Motions ◽  
Time History ◽  
Load Level ◽  
Steel Buildings ◽  
Moment Frames ◽  
Axial Loads ◽  
Steel Moment Resisting Frames ◽  
Moment Resisting Frames ◽  
Moment Resisting

This study focuses on exploring the seismic axial loads for columns in steel moment resisting frames (SMRFs) under strong ground motions. For this purpose, the increases in axial loads are investigated at the maximum lateral load level and the corresponding lateral displacement. The results are presented in terms of maximum amplification factors (Ω0) of all frame columns under the selected ground motions and axial load-moment levels in columns. four typical steel moment resisting frames representing typical low, medium and high rise steel buildings are designed based on the seismic design requirement in ASCE 7-10 and AISC 341-10 . An ensemble of ground motions range from moderate to severe are selected to identify the seismic response of each frames. Two sets of ground motions corresponding to 10% and 2% probability of exceedance are used in nonlinear dynamic time history analyses.

A Seismic Effective Method for Double-Layer Reticulated Shell Using Buckling-Restrained Braces

2010 ◽  
Vol 163-167 ◽  
pp. 2852-2856
Author(s):  
Chang Wu ◽  
Xiu Li Wang
Keyword(s):  
Double Layer ◽  
Seismic Performance ◽  
Linear Time ◽  
Ground Motions ◽  
Equations Of Motion ◽  
Time History ◽  
Original Structure ◽  
Loading Test ◽  
Strong Earthquakes ◽  
Buckling Restrained Braces

In this study a kind of buckling-restrained braces (BRBs) as energy dissipation dampers is attempted for seismic performance of large span double-layer reticulated shell and the effectiveness of BRBs to protect structures against strong earthquakes is numerically studied. The hysteretic curve of such members is obtained through the simulation of the cyclic-loading test, and the equations of motion of the system under earthquake excitations are established. BRBs are then placed at certain locations on the example reticulated shell to replace some normal members, and the damping effect of the two installation schemes of BRBs is investigated by non-linear time-history analyses under various ground motions representing major earthquake events. Compared with the seismic behavior of the original structure without BRBs, satisfactory seismic performance is seen in the upgraded models, which clarifies the BRBs can reduce the vibration response of spatial reticulated structure effectively and the new system has wide space to develop double layer reticulated shell.

scholarly journals Support structure design for New Zealand Forest Products Ltd's No. 5 Recovery Boiler

1987 ◽  
Vol 20 (1) ◽  
pp. 2-6
Author(s):  
R. D. Sharpe
Keyword(s):  
New Zealand ◽  
Seismic Performance ◽  
Time History ◽  
Forest Products ◽  
Structure Design ◽  
Seismic Resistance ◽  
Simple Application ◽  
Major Earthquake ◽  
Lateral Forces ◽  
Industrial Boilers

Internationally, the seismic resistance of large industrial boilers appears to be addressed by the most simple application of relatively low equivalent static lateral forces which are resisted elastically. This paper describes measures taken to ensure a predictable
and controlled seismic performance of such a boiler
during a major earthquake. Inelastic time-history methods of analysis were used to confirm that the desired performance would be achieved. As a result the client was able to purchase a relatively standard boiler in the international marketplace and still achieve a level of seismic resistance consistent with the best NZ practices.

Evaluation of Seismic Performance of Moment Resisting Frames considering Vertical Component of Ground Motion

2012 ◽  
Vol 15 (8) ◽  
pp. 1439-1453 ◽  
Author(s):  
Behrouz Asgarian ◽  
Anahita Norouzi ◽  
Pejman Alanjari ◽  
Masoud Mirtaheri
Keyword(s):  
Ground Motion ◽  
Seismic Performance ◽  
Vertical Component ◽  
Moment Resisting Frames ◽  
Moment Resisting

Duration of nuclear explosion ground motion

1978 ◽  
Vol 68 (4) ◽  
pp. 1133-1145
Author(s):  
Walter W. Hays ◽  
Kenneth W. King ◽  
Robert B. Park
Keyword(s):  
Epicentral Distance ◽  
Ground Motions ◽  
Broad Band ◽  
Time History ◽  
Ground Acceleration ◽  
Ground Shaking ◽  
Distance Range ◽  
Nuclear Explosions ◽  
Dependent Site ◽  
Strong Ground

abstract This paper evaluates the duration of strong ground shaking that results from nuclear explosions and identifies some of the problems associated with its determination. Knowledge of the duration of horizontal ground shaking is important out to epicentral distances of about 44 km and 135 km, the approximate distances at which the ground shaking level falls to 0.01 g for nuclear explosions having yields of about 100 kt and 1,000 kt, respectively. Evaluation of the strong ground motions recorded from the event STRAIT (ML = 5.6) on a linear array of five, broad-band velocity seismographs deployed in the distance range 3.2 to 19.5 km provides information about the characteristics of the duration of ground shaking. The STRAIT data show that: (1) the definition that is used for defining duration is very important; (2) the duration of ground acceleration, as defined in terms of 90 per cent of the integral of the squared time history (Trifunac and Brady, 1975), increased from about 4 to 26 sec over the approximately 20-km distance range; and (3) the duration of ground velocity and displacement were slightly greater because of the effect of the alluvium layer on the propagating surface waves. Data from other events (e.g., MILROW, CANNIKIN, HANDLEY, PURSE) augment the STRAIT data and show that: (1) duration of shaking is increased by frequency-dependent site effects and (2) duration of shaking, as defined by the integral of the squared time history, does not increase as rapidly with increase in yield as is indicated by other definitions of duration that are stated in terms of an amplitude threshold (e.g., bracketed duration, response envelopes). The available data suggest that the duration of ground acceleration, based on the integral definition, varies from about 4 to 40 sec for a 100-kt range explosion and from about 4 to 105 sec for a megaton range explosion in the epicentral distance range of 0 to 44 km and 0 to 135 km, respectively.

scholarly journals Experimental Study on Seismic Retrofitting of Reinforced Concrete Frames Using Welded Concrete-Filled Steel Tubes

2020 ◽  
Vol 10 (20) ◽  
pp. 7061 ◽  
Author(s):  
Kyong Min Ro ◽  
Min Sook Kim ◽  
Young Hak Lee
Keyword(s):  
Reinforced Concrete ◽  
Seismic Performance ◽  
Seismic Energy ◽  
Maximum Load ◽  
Steel Tube ◽  
Seismic Retrofitting ◽  
Reinforced Concrete Frame ◽  
Concrete Frame ◽  
Moment Resisting Frames ◽  
Moment Resisting

Buildings constructed with non-seismic details are at risk of damage and collapse when an earthquake occurs due to a lack of strength, stiffness, and ductility. For reinforced concrete (RC) moment-resisting frames, seismic retrofitting methods that can enhance strength or ductility should be applied. However, such strategies have many disadvantages related to constructability, serviceability, securing integrity, and cost. In this paper, a welded concrete-filled steel tube (WCFST) system was examined in order to resolve the problems of the existing seismic retrofitting methods for RC moment-resisting frames. To evaluate the seismic performance of the proposed system, two specimens, one with non-seismic details and another reinforced with a WCFST seismic system, were manufactured for the cyclic loading tests. As a result of the experiments, the specimen retrofitted with the WCFST system showed maximum load, effective stiffness, and energy dissipation capacity values approximately 3, 2, and 2.5 times greater, respectively, than those obtained from the existing reinforced concrete frame specimen. The experimental results indicate that the proposed WCFST system is expected to be effective at improving the seismic performance by enhancing both the strength of the existing reinforced concrete frame structures and the dissipation of the seismic energy.

Sign in / Sign up

Export Citation Format

Share Document