scholarly journals Influence of Allowances on Taking Log Deliveries

2021 ◽  
Vol 72 (1) ◽  
pp. 65-77
Author(s):  
Veronika Hunková ◽  
Karel Janák
Keyword(s):  
Measuring Equipment ◽  
Poor Quality ◽  
Raw Material ◽  
Mountainous Terrain ◽  
Electronic Measuring ◽  
Volume Calculation ◽  
Length Group ◽  
Round Wood ◽  
Accredited Laboratory ◽  
The Right

This paper deals with differences between the declared and actually supplied volume of round wood, which can be seen in the sawmill log yards in taking log deliveries. These differences usually mean the losses for the suppliers. Authors focus on the length accuracy of supplied logs. They start with a comprehensive manual checking of log deliveries (2639 logs) and with calibration of electronic measuring equipment (238 logs) made by an accredited laboratory. Authors analyse the origins of the differences, they quantify the volume “voluntarily” given by the suppliers in the form of oversized allowances and the volume of the losses caused by classifying the logs to a lower length group if the necessary allowance lengths are not observed (the volume is counted using e.g. 1 m shorter nominal length). The term “extra allowance” is introduced for allowances longer than wanted, and the dependences among the length of extra allowances, log diameter, volume of extra allowances and number of logs with too short allowance are defined. Losses caused by both of these defects (over- or under-sized logs) are counted and compared. If the log length value is exactly the required one or close to it (it means nominal length and required allowance), the measuring equipment can still measure a lower value because of the required precision of 1 %. Losses are also caused by reclassifying the logs to a lower group. Suppliers cut the logs longer (make “extra allowances”) to ensure that the volume calculation is based on the right nominal length and not shorter. The research shows big differences between particular suppliers and their losses caused by extra allowances or reclassification of logs. The authors searched the optimum allowance in order to minimise the losses of the supplier. The results of the analysis give the following recommendations: for suppliers who do not use harvesters for felling and logging, it would be preferable to supply round timber in tree lengths due to the volume lost by reclassification. Today, however, this is not possible in most cases because large customers buy only logs because of technological reasons. Another aspect is the price, which is usually higher for raw material in logs. In the production of logs, it is preferable to increase the required 2 % allowance by 4-5 cm, if it is possible to produce the logs relatively accurately. If accuracy cannot be maintained, it is preferable to increase the allowance to about 7 cm (e.g. mountainous terrain, poor quality and curved timber, lack of experienced staff).

Microcontroller Device for Conductor Identification Using Acoustic Signal

2020 ◽  
Vol 67 (1) ◽  
pp. 28-34
Author(s):  
Aleksandr V. Vinogradov ◽  
Aleksey V. Bukreev
Keyword(s):  
Acoustic Signal ◽  
Acoustic Waves ◽  
Theoretical Calculations ◽  
Poor Quality ◽  
Electrical Circuit ◽  
Research Purpose ◽  
Electrical Wiring ◽  
The Right ◽  
The Cost ◽  
Technical Solutions

When repairing and replacing electrical wiring in enterprises, the main difficulty is the lack or poor quality of documentation, plans for conductors laying. Distinguishing wires (cables) and their cores by the color of the shells or using tags attached to the ends is difficult if the shells have the same color and there are no tags. Devices and technical solutions used to identify wires and cables do not allow recognizing conductors without breaking the electrical circuit, removing insulation, and de-energizing the network. Searching for the right conductor is a time-consuming operation. (Research purpose) The research purpose is developing a new microcontroller device for identifying wires using an acoustic signal. (Materials and methods) Literature sources has been searched for devices for conductors identifying. (Results and discussion) The article proposes a method that involves feeding an acoustic signal to a wire at one point and capturing it at another, in order to recognize the desired wire. The article presents results of comparison of the developed microcontroller device for identifying conductors using an acoustic signal with known devices and methods for conductors recognizing. (Conclusions) The article reveals the shortcomings of existing methods and means of identifying wires and cables. Authors performed a theoretical calculation of the sound pressure in the conductor at a given distance. The article presents the calculation of speed of acoustic waves in conductors with different types of insulation. Authors designed a microcontroller device for identifying conductors using an acoustic signal and tested it. It was determined that the device increases the safety of work, reduces the cost of operating internal wiring and identification time; eliminates the violation of wire insulation, the need to disable electrical receivers. The convergence of theoretical calculations and experimental data was shown.

Universal Health Coverage

2017 ◽  
Author(s):  
Joia S. Mukherjee
Keyword(s):  
Health Care ◽  
Universal Health Coverage ◽  
Poor Quality ◽  
Theory And Practice ◽  
Health Coverage ◽  
Quality Health Care ◽  
The Sustainable Development ◽  
Quality Health ◽  
The Right ◽  
Universal Health

This chapter explores the seminal topic of Universal Health Coverage (UHC), an objective within the Sustainable Development goals. It reviews the theory and definitions that shape the current conversation on UHC. The movement from selective primary health care to UHC demonstrates a global commitment to the progressive realization of the right to health. However, access to UHC is limited by barriers to care, inadequate provision of care, and poor-quality services. To deliver UHC, it is critical to align inputs in the health system with the burden of disease. Quality of care must also be improved. Steady, sufficient financing is needed to achieve the laudable goal of UHC.This chapter highlights some important steps taken by countries to expand access to quality health care. Finally, the chapter investigates the theory and practice behind a morbidity-based approach to strengthening health systems and achieving UHC.

Biocatalysis and biomass conversion: enabling a circular economy

2020 ◽  
Vol 378 (2176) ◽  
pp. 20190274 ◽  
Author(s):  
Roger A. Sheldon
Keyword(s):  
Circular Economy ◽  
Biomass Conversion ◽  
Raw Material ◽  
Liquid Fuels ◽  
Waste Biomass ◽  
Renewable Biomass ◽  
Precious Metal Catalysts ◽  
Mitigate Climate Change ◽  
Forestry Residues ◽  
The Right

This paper is based on a lecture presented to the Royal Society in London on 24 June 2019. Two of the grand societal and technological challenges of the twenty-first century are the ‘greening' of chemicals manufacture and the ongoing transition to a sustainable, carbon neutral economy based on renewable biomass as the raw material, a so-called bio-based economy. These challenges are motivated by the need to eliminate environmental degradation and mitigate climate change. In a bio-based economy, ideally waste biomass, particularly agricultural and forestry residues and food supply chain waste, are converted to liquid fuels, commodity chemicals and biopolymers using clean, catalytic processes. Biocatalysis has the right credentials to achieve this goal. Enzymes are biocompatible, biodegradable and essentially non-hazardous. Additionally, they are derived from inexpensive renewable resources which are readily available and not subject to the large price fluctuations which undermine the long-term commercial viability of scarce precious metal catalysts. Thanks to spectacular advances in molecular biology the landscape of biocatalysis has dramatically changed in the last two decades. Developments in (meta)genomics in combination with ‘big data’ analysis have revolutionized new enzyme discovery and developments in protein engineering by directed evolution have enabled dramatic improvements in their performance. These developments have their confluence in the bio-based circular economy. This article is part of a discussion meeting issue ‘Science to enable the circular economy'.

A Hazard and Risk Management System for Large Rock Slope Hazards Affecting Pipelines in Mountainous Terrain

2002 ◽  
Author(s):  
Michael Porter ◽  
Alex Baumgard ◽  
K. Wayne Savigny
Keyword(s):  
Risk Management ◽  
Rock Slope ◽  
Management Program ◽  
South American ◽  
Mountainous Terrain ◽  
Hazard Exposure ◽  
Access Road ◽  
Hazard And Risk ◽  
The Right ◽  
Hazard Rating

Pipelines and other linear facilities that traverse mountainous terrain may be subject to rock fall and rock slide hazards. A system is required to determine which sites pose the greatest hazard to the facility. Once sites are ranked according to hazard exposure, a risk management program involving inspection, monitoring, contingency planning and/or mitigation can be implemented in a systematic and defensible manner. A hazard rating methodology was developed to identify and characterize rock slope hazards above a South American Concentrate Pipeline, and to provide a relative ranking of hazard exposure for the pipeline, an access road and operational personnel. The rating methodology incorporates the geometry of the right-of-way, estimated pipe depth, staff and vehicle occupancy time, failure mechanism and magnitude, and the annual probability of hazard occurrence. This information is used in a risk-based framework to assign relative hazard ratings within rock slope sections of relatively uniform hazard exposure. This paper outlines a general framework for natural hazard and risk management along linear facilities, describes the rock slope hazard rating methodology, and illustrates how the system was applied along a South American Concentrate Pipeline.

scholarly journals The Hungarian Wood-Based Panel Industry and its Impact on the Environment

2016 ◽  
Vol 12 (2) ◽  
pp. 157-172
Author(s):  
Gábor Laborczy ◽  
András Winkler
Keyword(s):  
Carbon Dioxide ◽  
Power Plants ◽  
Negative Impact ◽  
Value Added ◽  
Forest Products ◽  
Air Pollutant ◽  
Raw Material ◽  
Energy Sources ◽  
Forest Products Industry ◽  
Round Wood

Abstract It is well known that worldwide deforestation has a negative impact on the global environment. Forests play an important role in producing oxygen as well as retaining gases that create the greenhouse effect. Forests primarily absorb carbon dioxide, the major air pollutant released by the industrial activities. Energy production is the major source of environmental contamination. In addition to reducing CO2 emissions, another issue this industrial sector must tackle is to decrease the use of fossil fuels by substituting them with renewable, environmentally friendly energy sources. One of the answers to these challenges is the utilization of biomass as energy sources. However, biomass-based fuels include short bolts, split round-wood, pulpwood, bark and by-products of sawmilling, which are the raw materials for the wood-based panel industry as well.Wood utilization of the forest products industry has a major impact on the delayed release of carbon dioxide stored in the wood. All over the world, just as in Hungary, the wood-based panel industry mainly uses low quality wood resources and turns them into value added products. The elongation of the life cycle of low quality wood materials decreases CO2 emissions, thus significantly contributing to environmental protection. Furthermore, it is assumed that raw material demand of the wood-based panel industry could be satisfied by focusing on sustainable forest management and well-planned reforestation. Additionally, special energy-plantations may provide extra wood resources, while waste and other non-usable parts of trees contribute to the effective and economic operation of biomass utilizing power-plants. This paper summarizes the current situation of the Hungarian wood-based panel industry and discusses the effects of the panel manufacturing processes on the environment. Also, it outlines the possible future of this important segment of the forest products industry.

scholarly journals KARAKTERISTIK AMPLANG IKAN LELE DUMBO (Clarias gariepinus) HASIL VARIASI RASIO DAGING IKAN LELE DAN TAPIOKA

2020 ◽  
Vol 14 (02) ◽  
pp. 143
Author(s):  
Priyanto Priyanto ◽  
Yuli Wibowo ◽  
Jay Jayus
Keyword(s):  
Raw Materials ◽  
Clarias Gariepinus ◽  
Raw Material ◽  
Chi Square ◽  
Organoleptic Test ◽  
Fish Flesh ◽  
Randomized Design ◽  
Protein Properties ◽  
Tapioca Flour ◽  
The Right

The demand for amplang crackers is now increasing. However, the price of its raw material, mackerel fish, is generally higher compare to other fishes, causing the higher cost of this type crackers production. Effort to explore other fish as an alternative raw material is required to overcome the problems. Catfish is one of the choices to be used as raw material since this fish is more available in a market in a lower price, but the protein properties of this fish is different to mackarel, which will be possible to affect the nature of the crackers obtained. To produce catfish amplang crackers to be similar to common amplang product, it is necessary to find out the right composition of catfish and tapioca flour used. Therefore, the purpose of this research was to characterize physico-chemically and organoleptically, the catfish amplang crackers made under different ratio of fish flesh and starch. The experiment was designed using completely randomized design. Physico-chemical data obtained were analyzed using ANOVA, while the organoleptic test data were examined using chi-square method. The effectiveness test was carried out to find the proper ratio of raw materials composition used. The results showed that the higher the ratio of the fish flesh and the starch composition, the lower the texture value of the crackers as an indication of the decrease of its crispness. Although the lightness of the crackers was lowered by the addition of more starch to the dough, its linear expansion and hygroscopicity were not affected. The results of organoleptic test showed that the panelist was prefer to a higher crispness of crackers. The most preferable cracker was the one with 1:2.25 ratio of catfish flesh and starch, showing the characteristic of 1.80% moisture, 2.08% ash, 5.75% protein, 23.55% fat, and 66,93% carbohydrate. Keywords: cracker, catfish, tapioca starch

scholarly journals Pembuatan Bokasi Berbahan Dasar Jerami Bagi Masyarakat Kelompok Tani Di Desa Borikamase Kabupaten Maros

2021 ◽  
Vol 10 (1) ◽  
pp. 71
Author(s):  
Dian Safitri ◽  
Nurul Magfirah ◽  
Irmawanty Irmawaty ◽  
Haerul Syam
Keyword(s):  
Organic Fertilizer ◽  
Nutrient Content ◽  
Rice Fields ◽  
Raw Material ◽  
Organic Fertilizers ◽  
High Price ◽  
Farming Communities ◽  
Farming Community ◽  
Synthetic Fertilizers ◽  
The Right

The large number of rice fields in Borikamase Village, resulting in high production of hay, requires an appropriate effort to use straw into organic fertilizer or bokashi which is environmentally friendly as well as safe for plants. The use of straw into bokashi or organic fertilizer needs to be taught to the farming community, so the community service team focuses on providing assistance and training to the community in utilizing straw as a raw material in making bokashi by using microorganisms as the source of fermentation. In addition, the high price of synthetic fertilizers on the market makes farmers in Borikamase Village feel heavy in providing nutritional supplies to their agricultural areas, so that this training is expected to help farmers by obtaining fertilizers that are cheap, safe, and of good quality to fertilize. The existence of biotechnology applications, provides the right solution in overcoming the damage to bald mountains and the scarcity and high price of synthetic fertilizers, namely by processing straw into bokashi or organic fertilizers with high nutrient content and are safe for the environment. In addition, providing knowledge and skills for farming communities as agents of reform in restoring ecosystem balance through the application of bokashi made of straw on rice fields. Keywords: Training, Mentoring, Boricamase, Straw

Sign in / Sign up

Export Citation Format

Share Document