A Practical Joint-Space Trajectory Generation Method Based on Convolution in Real-Time Control

An optimization framework for upward jumping motion based on quadratic programming (QP) is proposed in this paper, which can simultaneously consider constraints such as the zero moment point (ZMP), limitation of angular accelerations, and anti-slippage. Our approach comprises two parts: the trajectory generation and real-time control. In the trajectory generation for the launch phase, we discretize the continuous trajectories and assume that the accelerations between the two sampling intervals are constant and transcribe the problem into a nonlinear optimization problem. In the real-time control of the stance phase, the over-constrained control objectives such as the tracking of the center of moment (CoM), angle, and angular momentum, and constraints such as the anti-slippage, ZMP, and limitation of joint acceleration are unified within a framework based on QP optimization. Input angles of the actuated joints are thus obtained through a simple iteration. The simulation result reveals that a successful upward jump to a height of 16.4 cm was achieved, which confirms that the controller fully satisfies all constraints and achieves the control objectives.

Download Full-text

Network-Oriented Real-Time Embedded System Considering Synchronous Joint Space Motion for an Omnidirectional Mobile Robot

Electronics ◽

10.3390/electronics8030317 ◽

2019 ◽

Vol 8 (3) ◽

pp. 317 ◽

Cited By ~ 3

Author(s):

Raimarius Delgado ◽

Byoung Choi

Keyword(s):

Mobile Robot ◽

Embedded System ◽

Real Time ◽

Low Cost ◽

Joint Space ◽

Geometric Constraints ◽

Real Time Control ◽

Synchronization Mechanism ◽

Omnidirectional Mobile Robot ◽

Time Control

This paper proposes a real-time embedded system for joint space control of omnidirectional mobile robots. Actuators driving an omnidirectional mobile robot are connected in a line topology which requires synchronization to move simultaneously in translation and rotation. We employ EtherCAT, a real-time Ethernet network, to control servo controllers for the mobile robot. The first part of this study focuses on the design of a low-cost embedded system utilizing an open-source EtherCAT master. Although satisfying real-time constraints is critical, a desired trajectory on the center of the mobile robot should be decomposed into the joint space to drive the servo controllers. For the center of the robot, a convolution-based path planner and a corresponding joint space control algorithm are presented considering its physical limits. To avoid obstacles that introduce geometric constraints on the curved path, a trajectory generation algorithm considering high curvature turning points is adapted for an omnidirectional mobile robot. Tracking a high curvature path increases mathematical complexity, which requires precise synchronization between the actuators of the mobile robot. An improvement of the distributed clock—the synchronization mechanism of EtherCAT for slaves—is presented and applied to the joint controllers of the mobile robot. The local time of the EtherCAT master is dynamically adjusted according to the drift of the reference slave, which minimizes the synchronization error between each joint. Experiments are conducted on our own developed four-wheeled omnidirectional mobile robot. The experiment results confirm that the proposed system is very effective in real-time control applications for precise motion control of the robot even for tracking high curvature paths.

Download Full-text

A Real Time Control Architecture for Continuously Managing Patients in a Care Unit

Methods of Information in Medicine ◽

10.1055/s-0038-1634619 ◽

1995 ◽

Vol 34 (05) ◽

pp. 475-488

Author(s):

B. Seroussi ◽

J. F. Boisvieux ◽

V. Morice

Keyword(s):

Real Time ◽

Linear Time ◽

Treatment Plan ◽

Control Architecture ◽

Real Time Control ◽

Time Representation ◽

Time Control ◽

Continuous Support ◽

Definition Of ◽

Computerized System

Abstract:The monitoring and treatment of patients in a care unit is a complex task in which even the most experienced clinicians can make errors. A hemato-oncology department in which patients undergo chemotherapy asked for a computerized system able to provide intelligent and continuous support in this task. One issue in building such a system is the definition of a control architecture able to manage, in real time, a treatment plan containing prescriptions and protocols in which temporal constraints are expressed in various ways, that is, which supervises the treatment, including controlling the timely execution of prescriptions and suggesting modifications to the plan according to the patient’s evolving condition. The system to solve these issues, called SEPIA, has to manage the dynamic, processes involved in patient care. Its role is to generate, in real time, commands for the patient’s care (execution of tests, administration of drugs) from a plan, and to monitor the patient’s state so that it may propose actions updating the plan. The necessity of an explicit time representation is shown. We propose using a linear time structure towards the past, with precise and absolute dates, open towards the future, and with imprecise and relative dates. Temporal relative scales are introduced to facilitate knowledge representation and access.

Download Full-text