scholarly journals Nose-Angle Bridge Piers as Alternative Countermeasures for Local Scour Reduction

2018 ◽  
Vol 13 (2) ◽  
pp. 110-120 ◽  
Author(s):  
Ibtesam Abudallah Habib ◽  
Wan Hanna Melini Wan Mohtar ◽  
Atef Elsaiad ◽  
Ahmed El-Shafie
Keyword(s):  
Froude Number ◽  
Local Scour ◽  
Bridge Piers ◽  
Scour Depth ◽  
Skew Angle ◽  
Flow Angle ◽  
Sediment Size ◽  
Low Froude Number ◽  
Skew Angles ◽  
Depth Reduction

This study investigates the performance nose-angle piers as countermeasures for local scour reduction around piers. Four nose angles were studied, i.e., 90°, 70°, 60° and 45° and tested in a laboratory. The sediment size was fixed at 0.39 mm whereas the flow angle of attack (or skew angle) was varied at four angles, i.e., skew angles, i.e., 0°, 10°, 20° and 30°. Scour reduction was clear when decreasing nose angles and reached maximum when the nose angle is 45°. Increasing the flow velocity and skew angle was subsequently increasing the scour profile, both in vertical and transversal directions. However, the efficiency of nose angle piers was only high at low Froude number less than 0.40 where higher Froude number gives minimal changes in the maximum scour depth reduction. At a higher skew angle, although showed promising maximum scour depth reduction, the increasing pier projected width resulted in the increase of transversal lengths.

scholarly journals Investigation of local scour around tandem piers for different skew-angles

2018 ◽  
Vol 40 ◽  
pp. 03008 ◽  
Author(s):  
Sargol Memar ◽  
Mohammad Zounemat-Kermani ◽  
Ali-Asghar Beheshti ◽  
Giovanni De Cesare ◽  
Anton J. Schleiss
Keyword(s):  
Flow Direction ◽  
Local Scour ◽  
Scour Depth ◽  
Skew Angle ◽  
Approach Velocity ◽  
Sheltering Effect ◽  
Skew Angles

In the present study the effect of the skew-angle of the alignment of tandem piers on local scour depth around them is investigated. The tandem piers were aligned with different skew-angles of θ=0°,30°,45°,60°,90° with respect to the flow direction. The results indicatethat with the increment of the skew-angle, the influence of sheltering effects is decreased. In other word, since the sheltering effect of the upstream pier is declined (which reduces the approach velocity for the downstream pier) the scour depth around downstream pier increases. The results show that the maximum scour depth occurs at both piers for the skew-angle of θ=45°.Furthermore, the best configuration to aligned tandem piers was achieved at the skew-angle of θ=30°.

scholarly journals Physical Modeling of Spatial and Temporal Development of Local Scour at the Downstream of Bed Protection for Low Froude Number

Water ◽  
2019 ◽  
Vol 11 (5) ◽  
pp. 1041 ◽  
Author(s):  
Sung Won Park ◽  
Jin Hwan Hwang ◽  
Jungkyu Ahn
Keyword(s):  
Equilibrium State ◽  
Froude Number ◽  
Fixed Bed ◽  
Local Scour ◽  
Dominant Factor ◽  
Scour Depth ◽  
Dimensionless Time ◽  
Temporal Development ◽  
Low Froude Number ◽  
Bed Protection

Local scour at the downstream of the river bed protection is one of the most important parameters for the design criteria and sustainable management of the hydraulic structures. Previously, various researches on its process in the equilibrium state have been suggested with experimental and numerical approaches. In this study, relatively long-term laboratory experiments of local scouring at the downstream of fixed bed in an open channel were conducted with mono-granular sediment bed and analyzed about maximum scour depth and its temporal development. In particular, we conducted experiments with relatively low Froude number (less than 0.5) and their duration of tests was exceeded over 700 hours. We modified the relationship between the dimensionless time and length scales of the maximum scour depth of the local scour hole based on the turbulent shear layer thickness. A new functional relationship between dominant factors and the maximum scour depth in the equilibrium state were suggested and compared with previously suggested formula. Also, from the results by nonlinear regression, Froude number was founded as a dominant factor on the prediction of equilibrium maximum scour depth.

Clear-water local scour at wide piers in shallow-water flow

2014 ◽  
Vol 9 (3) ◽  
pp. 331-343 ◽  
Author(s):  
N. Ahmad ◽  
T. Mohamed ◽  
F. H. Ali ◽  
B. Yusuf
Keyword(s):  
Laboratory Data ◽  
Local Scour ◽  
The Other ◽  
Scour Depth ◽  
Temporal Development ◽  
Clear Water ◽  
Shallow Water Flow ◽  
Equilibrium Time ◽  
Sediment Size ◽  
Flow Intensity

Laboratory data for local scour depth regarding the size of wide piers are presented. Clear water scour tests were performed for various pier widths (0.06, 0.076, 0.102, 0.14 and 0.165 m), two types of pier shapes (circular and rectangular) and two types of uniform cohesionless bed sediment (d50 = 0.23 and d50 = 0.80 mm). New data are presented and used to demonstrate the effects of pier width, pier shape and sediment size on scour depth. The influence of equilibrium time (te) on scouring processes is also discussed. Equilibrium scour depths were found to decrease with increasing values of b/d50. The temporal development of equilibrium local scour depth with new laboratory data is demonstrated for flow intensity V/Vc = 0.95. On the other hand, the results of scour mechanism have shown a significant relationship between normalized volume of scoured and deposited with pier width, b. The experimental data obtained in this study and data available from the literature for wide piers are used to evaluate predictions of existing methods.

Clear-water scour at bridge piers in fine and medium gravel beds

2005 ◽  
Vol 32 (4) ◽  
pp. 775-781 ◽  
Author(s):  
Rajkumar V Raikar ◽  
Subhasish Dey
Keyword(s):  
Bridge Piers ◽  
Geometric Standard Deviation ◽  
Scour Depth ◽  
Size Factor ◽  
Clear Water ◽  
Envelope Curve ◽  
Gravel Beds ◽  
Sediment Size ◽  
Gravel Size ◽  
Equilibrium Scour Depth

An experimental investigation on scour at circular and square piers in uniform and non-uniform gravels (fine and medium sizes) under clear-water scour at limiting stability of gravels is presented. From the experimental results, it is observed that the equilibrium scour depth increases with decrease in gravel size. The variation of equilibrium scour depth with gravel sizes departures considerably from that with sand sizes. Consequently, the resulting sediment size factors for gravels, obtained from envelope curve fitting, are significantly different from the existing sediment size factor for sands. The influence of gravel gradation on scour depth is also prominent in non-uniform gravels. The time scales to represent the time variation of scour depth in uniform and non-uniform gravels are determined. For uniform gravels, the non-dimensional time scale increases with increase in pier Froude number and gravel size, whereas for non-uniform gravels, it decreases with increase in geometric standard deviation of particle size distribution of gravels.Key words: bridge pier, gravel beds, scour, erosion, sediment transport, open channel flow, hydraulic engineering.

Maximum local scour depth at bridge piers and abutments

1998 ◽  
Vol 36 (2) ◽  
pp. 183-198 ◽  
Author(s):  
J.K. Kandasamy ◽  
B.W. Melville
Keyword(s):  
Local Scour ◽  
Bridge Piers ◽  
Scour Depth

scholarly journals Investigation of Local Scour around L-Shape Submerged Groynes in Clearwater Conditions

2021 ◽  
Vol 28 (3) ◽  
pp. 159-169
Author(s):  
Saleh Issa Khassaf ◽  
Budoor Mohammed Rashak
Keyword(s):  
Froude Number ◽  
Local Scour ◽  
Scour Depth ◽  
Contour Lines ◽  
Low Profile ◽  
Scour Hole ◽  
Number Flow ◽  
Flow Intensity ◽  
Good Determination ◽  
New Formula

Submerged Groynes are low profile linear structures that are generally located on the outside bank to form Groynes fields and prevent the erosion of stream banks by redirecting high-velocity flow away from the bank. This research was studied in detail through two major stages. The first stage of the study is based on laboratory experiments to measure the development of local scour around L-shape submerged Groyne with the time, and special attention is given to the effects of different hydraulic and geometric parameters on local scour. Also; maps were drawn showing contour lines that represented the bed levels for maximum scour depth after reaching the equilibrium case. The result showed that a decrease in the scour depth ratio due to the increasing submerged ratio, and the number of Groynes. While the scour hole geometry will increase with the Froude number, flow intensity, and the spacing between Groynes, the decreasing percentage in the scour hole was measured to be about (4.3) % and (4.4) % for decreasing the spacing between Groynes from (2Lg) to (1.5Lg). Besides, it was range about (11.1) % and (14.0) % when reducing the spacing from (1.5Lg) to (Lg) under the same value of maximum Froude number. The second stage of the study is based on experimental results. A new formula was developed by using statistical analysis and it was found that a good determination coefficient.

Three-dimensional numerical simulation of local scour in the vicinity of circular side-by-side bridge piers with ice cover

2020 ◽  
Author(s):  
Mohammad Reza Namaee ◽  
Jueyi Sui ◽  
Yongsheng Wu ◽  
Natalie Linklater
Keyword(s):  
Laboratory Experiments ◽  
Transport Model ◽  
Numerical Models ◽  
Three Dimensional ◽  
Ice Cover ◽  
Local Scour ◽  
Bridge Piers ◽  
Accurate Estimation ◽  
Scour Depth ◽  
Cold Regions

Local scour around piers is one of the primary causes of collapse of bridges that cross rivers. The most severe scouring occurs in cold regions where ice cover significantly changes the velocity profile. Having an accurate estimation of the maximum scour depth around bridge piers, especially in cold regions, is necessary for a safer design of piers. In this study, 3-D numerical models are compared to laboratory experiments to examine the process of local scour around bridge piers with and without smooth and rough ice cover. By using the equation of Meyer-Peter Müller, the sediment transport model is validated to approximate the transport of the sediment particles. Numerical results showed good agreements with experimental observations where the maximum scour depth and Turbulent Kinetic Energy (TKE) around bridge piers were the highest under rough ice cover conditions.

scholarly journals Local Scour of Bridge Pier Sited on a Multi-Layered Sedimentary Bed in Rivers

2020 ◽  
Vol 144 ◽  
pp. 01008
Author(s):  
Shaolin Yue ◽  
Huan Zhou ◽  
Wenlong Zhu ◽  
Minxi Zhang
Keyword(s):  
Local Scour ◽  
Bridge Pier ◽  
Maximum Depth ◽  
Bridge Piers ◽  
Scour Depth ◽  
Bridge Safety ◽  
Particle Sorting ◽  
River Bed ◽  
Weihe River ◽  
Sediment Particles

The riverbeds or sea beds are usually composed of multi-layers of sediments. The scour around bridge piers sited on such beds is vital to the bridge safety, but is still very difficult to be predicated as its complicated interaction between the flow and bed layers. A simple model is proposed in this study for calculating the local scour maximum depth around bridge piers sited on multi-layer of sedimentary bed, which is based on HEC-18 formula revised by Richardson and Davis (2001) and the formula of the repose angle of sediment particles proposed by Cheng (1993). This model considers the particle sorting when the scour proceeds. An application of the model into the local scour depth of Guopan bridge pier sited on the Weihe River bed in Baoji city of China preliminarily demonstrates its reliability to calculate the local scour maximum depth around bridge piers sited on multi-layer of sedimentary bed.

Maximum Local Scour Depth at Bridge Piers under Unsteady Flow

2009 ◽  
Vol 135 (7) ◽  
pp. 609-614 ◽  
Author(s):  
Jihn-Sung Lai ◽  
Wen-Yi Chang ◽  
Chin-Lien Yen
Keyword(s):  
Unsteady Flow ◽  
Local Scour ◽  
Bridge Piers ◽  
Scour Depth

scholarly journals Improving the 2D Numerical Simulations on Local Scour Hole around Spur Dikes

Water ◽  
2021 ◽  
Vol 13 (11) ◽  
pp. 1462
Author(s):  
Chung-Ta Liao ◽  
Keh-Chia Yeh ◽  
Yin-Chi Lan ◽  
Ren-Kai Jhong ◽  
Yafei Jia
Keyword(s):  
Numerical Simulation ◽  
Three Dimensional ◽  
Local Scour ◽  
Bridge Piers ◽  
Scour Depth ◽  
Foundation Design ◽  
Mobile Bed ◽  
Scour Hole ◽  
Scour Holes ◽  
Spur Dikes

Local scour is a common threat to structures such as bridge piers, abutments, and dikes that are constructed on natural rivers. To reduce the risk of foundation failure, the understanding of local scour phenomenon around hydraulic structures is important. The well-predicted scour depth can be used as a reference for structural foundation design and river management. Numerical simulation is relatively efficient at studying these issues. Currently, two-dimensional (2D) mobile-bed models are widely used for river engineering. However, a common 2D model is inadequate for solving the three-dimensional (3D) flow field and local scour phenomenon because of the depth-averaged hypothesis. This causes the predicted scour depth to often be underestimated. In this study, a repose angle formula and bed geometry adjustment mechanism are integrated into a 2D mobile-bed model to improve the numerical simulation of local scour holes around structures. Comparison of the calculated and measured bed variation data reveals that a numerical model involving the improvement technique can predict the geometry of a local scour hole around spur dikes with reasonable accuracy and reliability.

Sign in / Sign up

Export Citation Format

Share Document