scholarly journals Improving the 2D Numerical Simulations on Local Scour Hole around Spur Dikes

Water ◽  
2021 ◽  
Vol 13 (11) ◽  
pp. 1462
Author(s):  
Chung-Ta Liao ◽  
Keh-Chia Yeh ◽  
Yin-Chi Lan ◽  
Ren-Kai Jhong ◽  
Yafei Jia
Keyword(s):  
Numerical Simulation ◽  
Three Dimensional ◽  
Local Scour ◽  
Bridge Piers ◽  
Scour Depth ◽  
Foundation Design ◽  
Mobile Bed ◽  
Scour Hole ◽  
Scour Holes ◽  
Spur Dikes

Local scour is a common threat to structures such as bridge piers, abutments, and dikes that are constructed on natural rivers. To reduce the risk of foundation failure, the understanding of local scour phenomenon around hydraulic structures is important. The well-predicted scour depth can be used as a reference for structural foundation design and river management. Numerical simulation is relatively efficient at studying these issues. Currently, two-dimensional (2D) mobile-bed models are widely used for river engineering. However, a common 2D model is inadequate for solving the three-dimensional (3D) flow field and local scour phenomenon because of the depth-averaged hypothesis. This causes the predicted scour depth to often be underestimated. In this study, a repose angle formula and bed geometry adjustment mechanism are integrated into a 2D mobile-bed model to improve the numerical simulation of local scour holes around structures. Comparison of the calculated and measured bed variation data reveals that a numerical model involving the improvement technique can predict the geometry of a local scour hole around spur dikes with reasonable accuracy and reliability.

Three-dimensional numerical simulation of local scour in the vicinity of circular side-by-side bridge piers with ice cover

2020 ◽  
Author(s):  
Mohammad Reza Namaee ◽  
Jueyi Sui ◽  
Yongsheng Wu ◽  
Natalie Linklater
Keyword(s):  
Laboratory Experiments ◽  
Transport Model ◽  
Numerical Models ◽  
Three Dimensional ◽  
Ice Cover ◽  
Local Scour ◽  
Bridge Piers ◽  
Accurate Estimation ◽  
Scour Depth ◽  
Cold Regions

Local scour around piers is one of the primary causes of collapse of bridges that cross rivers. The most severe scouring occurs in cold regions where ice cover significantly changes the velocity profile. Having an accurate estimation of the maximum scour depth around bridge piers, especially in cold regions, is necessary for a safer design of piers. In this study, 3-D numerical models are compared to laboratory experiments to examine the process of local scour around bridge piers with and without smooth and rough ice cover. By using the equation of Meyer-Peter Müller, the sediment transport model is validated to approximate the transport of the sediment particles. Numerical results showed good agreements with experimental observations where the maximum scour depth and Turbulent Kinetic Energy (TKE) around bridge piers were the highest under rough ice cover conditions.

scholarly journals Velocity profiles and turbulence intensities around side-by-side bridge piers under ice-covered flow condition

2020 ◽  
Vol 68 (1) ◽  
pp. 70-82
Author(s):  
Mohammad Reza Namaee ◽  
Jueyi Sui
Keyword(s):  
Flow Condition ◽  
Three Dimensional ◽  
Velocity Profiles ◽  
Local Scour ◽  
Bridge Piers ◽  
Scour Depth ◽  
Measured Velocity ◽  
Acoustic Doppler Velocimetry ◽  
The Difference ◽  
Do So

AbstractRecent studies have shown that the presence of ice cover leads to an intensified local scour pattern in the vicinity of bridge piers. To investigate the local scour pattern in the vicinity of bridge pier under ice-covered flow condition comparing to that under open channel flow condition, it is essential to examine flow field around bridge piers under different flow conditions. In order to do so, after creation of smooth and rough ice covers, three-dimensional timeaveraged velocity components around four pairs of bridge piers were measured using an Acoustic Doppler velocimetry (ADV). The ADV measured velocity profiles describe the difference between the velocity distributions in the vicinity of bridge piers under different covered conditions. Experimental results show that the vertical velocity distribution which represents the strength of downfall velocity is the greatest under rough covered condition which leads to a greater scour depth. Besides, results show that the turbulent intensity increases with pier size regardless of flow cover, which implies that larger scour depth occurs around piers with larger diameter.

Reduction of local scour around a bridge pier by using different shapes of pier slots and collars

2020 ◽  
Vol 20 (3) ◽  
pp. 1006-1015 ◽  
Author(s):  
A. Bestawy ◽  
T. Eltahawy ◽  
A. Alsaluli ◽  
A. Almaliki ◽  
M. Alqurashi
Keyword(s):  
Three Dimensional ◽  
Laser Scanner ◽  
Local Scour ◽  
Bridge Pier ◽  
Bridge Piers ◽  
Scour Depth ◽  
Contour Maps ◽  
Reduction Methods ◽  
Analysis System ◽  
Bridge Failure

Abstract Local scour around bridge piers is one of the main causes of bridge failure all over the world. Experimental and hydraulic models were carried out to investigate two types of scour reduction methods around a single cylindrical pier, namely the pier's slots and collars. The efficiency of various types of pier slots and circular collars around the pier's base in reducing scour were studied. A new shape of a conical collar was developed by the authors and examined along with other shapes. The results revealed that collars, in general, have more influence in reducing scour depth than slots made in the front and rear of bridge piers. The sigma-slot acts better than other tested slots, with a reduction in the scour depths of 59.3% and 52.8% at the upstream and downstream of the pier, respectively. On the other hand, the conical collar appeared to be the most effective collar shape in reducing the scour around the bridge pier, with a 61.1% reduction in the scour depth downstream of the pier. A three-dimensional laser scanner was used to capture the bed topography at the end of each experiment and contour maps of the deformed bed were produced. A one-dimensional Hydrologic Engineering Center-River Analysis System model was developed with a single bridge pier to predict the scour depth around the pier in an attempt to introduce new values for the pier nose shape factor, , which describes the tested piers.

scholarly journals Nose-Angle Bridge Piers as Alternative Countermeasures for Local Scour Reduction

2018 ◽  
Vol 13 (2) ◽  
pp. 110-120 ◽  
Author(s):  
Ibtesam Abudallah Habib ◽  
Wan Hanna Melini Wan Mohtar ◽  
Atef Elsaiad ◽  
Ahmed El-Shafie
Keyword(s):  
Froude Number ◽  
Local Scour ◽  
Bridge Piers ◽  
Scour Depth ◽  
Skew Angle ◽  
Flow Angle ◽  
Sediment Size ◽  
Low Froude Number ◽  
Skew Angles ◽  
Depth Reduction

This study investigates the performance nose-angle piers as countermeasures for local scour reduction around piers. Four nose angles were studied, i.e., 90°, 70°, 60° and 45° and tested in a laboratory. The sediment size was fixed at 0.39 mm whereas the flow angle of attack (or skew angle) was varied at four angles, i.e., skew angles, i.e., 0°, 10°, 20° and 30°. Scour reduction was clear when decreasing nose angles and reached maximum when the nose angle is 45°. Increasing the flow velocity and skew angle was subsequently increasing the scour profile, both in vertical and transversal directions. However, the efficiency of nose angle piers was only high at low Froude number less than 0.40 where higher Froude number gives minimal changes in the maximum scour depth reduction. At a higher skew angle, although showed promising maximum scour depth reduction, the increasing pier projected width resulted in the increase of transversal lengths.

scholarly journals Viscosity effects on local scour around vertical structures in clear-water conditions

2018 ◽  
Vol 40 ◽  
pp. 03038 ◽  
Author(s):  
Costantino Manes ◽  
Francesco Coscarella ◽  
Ashley Rogers ◽  
Roberto Gaudio
Keyword(s):  
Local Scour ◽  
Hydraulic Structures ◽  
Scour Depth ◽  
Foundation Design ◽  
Viscous Forces ◽  
Erosion Rates ◽  
Sediment Removal ◽  
Viscosity Effects ◽  
Horseshoe Vortices ◽  
Equilibrium Scour Depth

Local scour represents the erosion process that occurs at the base of hydraulic structures overlying sediment beds. Horseshoe vortices forming at the bed-structure junction are the main responsible for sediment removal and dictate erosion rates as well as the maximum erosion depth resulting from a significant flow event. In steady-flow conditions this is often referred to as the equilibrium scour depth, which, for many hydraulic structures, represents a key parameter for foundation-design and risk-assessment purposes. The equilibrium scour depth has been investigated for decades and many predictive formulae have been developed following the classical empirical approach, whereby numerous experimental datasets are used to isolate and identify the influence of non-dimensional groups emerging from dimensional analysis. Within this context, the influence of obstacle Reynolds numbers, and consequently of viscous forces, has always been neglected because of the large Re values normally encountered in engineering and laboratory conditions. The present paper demonstrates that this assumption is largely incorrect especially for beds made of sand or finer material. The theoretical analysis presented in Manes and Brocchini ([1]) is herein extended to include viscosity effects and investigate their importance on equilibrium scour depths forming around obstacles resembling bridge piers.

scholarly journals Effect of Inclination Angles on the Local Scour around a Submerged Cylinder

Water ◽  
2020 ◽  
Vol 12 (10) ◽  
pp. 2687
Author(s):  
Shaohua Wang ◽  
Shiyu Yang ◽  
Zhiguo He ◽  
Li Li ◽  
Yuezhang Xia
Keyword(s):  
Inclination Angle ◽  
Stokes Equations ◽  
Transport Model ◽  
Three Dimensional ◽  
Vertical Cylinder ◽  
Horseshoe Vortex ◽  
Local Scour ◽  
Scour Depth ◽  
Ocean Engineering ◽  
Bed Morphology

In ocean engineering and coastal environmental studies, local scour around a submerged structure is a typical issue, which is affected by the inclination of the structure. To investigate the effect of inclination directions and angles on flow structure and the bed morphology, a three-dimensional numerical model of a submerged inclined cylinder was established. In this model, the hydrodynamics are solved from the RANS (Reynolds-averaged Navier–Stokes) equations closed with the RNG k-ε turbulence model, while the bed morphology evolution is captured by the sediment transport model. In the case of vertical-cylinder scour, the simulation results agree well with existing laboratory experiments. In the cases of inclined-cylinder scour, the results show that the inclination direction not only changes the intensity and the location of the downflow but also modulates the pattern of the horseshoe vortex in front of the cylinder, thus influencing the local scour depth and the morphology of the bed. Compared with the case of vertical cylinder, the scour around an upstream-inclined cylinder is deeper, mainly due to the enhancement of downflow in front of the cylinder. The scour around a downstream-inclined cylinder is shallower and broader due to the weakened downflow and accelerated incoming flow. The maximum scour depth decreases with the inclination angle in the downstream-inclination case. In the upstream-inclination case, the maximum scour depth does not vary monotonously with the inclination angle, which results from a competitive effect of the horseshoe vortex and downflow in the front of the cylinder.

Formula Type of Local Scour Depth on Spur Dike Nose

2014 ◽  
Vol 641-642 ◽  
pp. 271-274
Author(s):  
Qiang Ying
Keyword(s):  
Formation Process ◽  
Local Scour ◽  
Scour Depth ◽  
Calculation Methods ◽  
Spur Dike ◽  
Scour Hole ◽  
Main Factors ◽  
Formula Type ◽  
Suggested Formula

This passage introduces the formation process of scour hole, analyzes the main factors contributed to the local scour hole’s depth and classifies today’s calculation methods of scour depth into three categories. Then, given the conditions where those methods can be applied and drawbacks of those methods, this article also recommends some suggested formula in calculation.

Maximum local scour depth at bridge piers and abutments

1998 ◽  
Vol 36 (2) ◽  
pp. 183-198 ◽  
Author(s):  
J.K. Kandasamy ◽  
B.W. Melville
Keyword(s):  
Local Scour ◽  
Bridge Piers ◽  
Scour Depth

scholarly journals Investigation of Local Scour around L-Shape Submerged Groynes in Clearwater Conditions

2021 ◽  
Vol 28 (3) ◽  
pp. 159-169
Author(s):  
Saleh Issa Khassaf ◽  
Budoor Mohammed Rashak
Keyword(s):  
Froude Number ◽  
Local Scour ◽  
Scour Depth ◽  
Contour Lines ◽  
Low Profile ◽  
Scour Hole ◽  
Number Flow ◽  
Flow Intensity ◽  
Good Determination ◽  
New Formula

Submerged Groynes are low profile linear structures that are generally located on the outside bank to form Groynes fields and prevent the erosion of stream banks by redirecting high-velocity flow away from the bank. This research was studied in detail through two major stages. The first stage of the study is based on laboratory experiments to measure the development of local scour around L-shape submerged Groyne with the time, and special attention is given to the effects of different hydraulic and geometric parameters on local scour. Also; maps were drawn showing contour lines that represented the bed levels for maximum scour depth after reaching the equilibrium case. The result showed that a decrease in the scour depth ratio due to the increasing submerged ratio, and the number of Groynes. While the scour hole geometry will increase with the Froude number, flow intensity, and the spacing between Groynes, the decreasing percentage in the scour hole was measured to be about (4.3) % and (4.4) % for decreasing the spacing between Groynes from (2Lg) to (1.5Lg). Besides, it was range about (11.1) % and (14.0) % when reducing the spacing from (1.5Lg) to (Lg) under the same value of maximum Froude number. The second stage of the study is based on experimental results. A new formula was developed by using statistical analysis and it was found that a good determination coefficient.

Sign in / Sign up

Export Citation Format

Share Document