scholarly journals INVESTIGATION OF MECHANISM FOR SOLID PHASE REACTION BY RAPID THERMAL ANNEALING IN Ti-Si SYSTEM

1990 ◽  
Vol 39 (7) ◽  
pp. 127
Author(s):  
CHEN CUN-LI ◽  
LI JIAN-NIAN ◽  
HUA WEN-YU
Keyword(s):  
Thermal Annealing ◽  
Rapid Thermal Annealing ◽  
Solid Phase ◽  
Solid Phase Reaction ◽  
Phase Reaction

Cobalt disilicide formed by rapid thermal annealing and throughmetal arsenic implantation

1991 ◽  
Vol 6 (9) ◽  
pp. 1892-1899 ◽  
Author(s):  
Edmund P. Burte ◽  
Min Ye
Keyword(s):  
Thermal Annealing ◽  
Rapid Thermal Annealing ◽  
Metal Ion ◽  
Silicon Oxide ◽  
Solid Phase ◽  
Ion Beam ◽  
Solid Phase Reaction ◽  
Phase Reaction ◽  
Cobalt Disilicide ◽  
Cobalt Silicides

Cobalt disilicide CoSi2 of a specific resistivity of 23 μω was formed by the solid phase reaction of cobalt and silicon in the phase sequence of Co2Si, CoSi, and CoSi2 by use of rapid thermal annealing. The through-metal arsenic implantation caused the mixing of cobalt with the silicon substrate and the formation of cobalt silicides. A significant lateral growth of cobalt silicides was observed in samples subjected to one-step rapid thermal annealing process at 900 °C without through-metal ion implantation. Ion beam mixing reduced this lateral silicide growth efficiently, but resulted in a higher density of cobalt atoms remaining in the silicon oxide film than after rapid thermal annealing, as revealed by vapor phase decomposition atomic absorption spectroscopy.

scholarly journals Fe3O4@C Nanoparticles Synthesized by In Situ Solid-Phase Method for Removal of Methylene Blue

Nanomaterials ◽  
2021 ◽  
Vol 11 (2) ◽  
pp. 330
Author(s):  
Hengli Xiang ◽  
Genkuan Ren ◽  
Yanjun Zhong ◽  
Dehua Xu ◽  
Zhiye Zhang ◽  
...  
Keyword(s):  
Methylene Blue ◽  
Solid Phase ◽  
Raw Materials ◽  
Phase Method ◽  
Maximum Adsorption Capacity ◽  
High Catalytic Activity ◽  
Solid Phase Reaction ◽  
Phase Reaction ◽  
High Concentrations

Fe3O4@C nanoparticles were prepared by an in situ, solid-phase reaction, without any precursor, using FeSO4, FeS2, and PVP K30 as raw materials. The nanoparticles were utilized to decolorize high concentrations methylene blue (MB). The results indicated that the maximum adsorption capacity of the Fe3O4@C nanoparticles was 18.52 mg/g, and that the adsorption process was exothermic. Additionally, by employing H2O2 as the initiator of a Fenton-like reaction, the removal efficiency of 100 mg/L MB reached ~99% with Fe3O4@C nanoparticles, while that of MB was only ~34% using pure Fe3O4 nanoparticles. The mechanism of H2O2 activated on the Fe3O4@C nanoparticles and the possible degradation pathways of MB are discussed. The Fe3O4@C nanoparticles retained high catalytic activity after five usage cycles. This work describes a facile method for producing Fe3O4@C nanoparticles with excellent catalytic reactivity, and therefore, represents a promising approach for the industrial production of Fe3O4@C nanoparticles for the treatment of high concentrations of dyes in wastewater.

Microstructure and Mechanical Properties of ZrB2/h-BN Multiphase Ceramics by Low-Temperature Reactive Sintering

2016 ◽  
Vol 697 ◽  
pp. 510-514 ◽  
Author(s):  
Feng Rui Zhai ◽  
Ke Shan ◽  
Ruo Meng Xu ◽  
Min Lu ◽  
Zhong Zhou Yi ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Relative Density ◽  
Fracture Strength ◽  
Solid Phase ◽  
Raw Materials ◽  
Solid Phase Reaction ◽  
Phase Reaction ◽  
Microstructure And Mechanical Properties ◽  
Multiphase Ceramics ◽  
Strength And Toughness

In the present paper, the ZrB2/h-BN multiphase ceramics were fabricated by SPS (spark plasma sintering) technology at lower sintering temperature using h-BN, ZrO2, AlN and Si as raw materials and B2O3 as a sintering aid. The phase constitution and microstructure of specimens were analyzed by XRD and SEM. Moreover, the effects of different sintering pressures on the densification, microstructure and mechanical properties of ZrB2/h-BN multiphase ceramics were also systematically investigated. The results show that the ZrB2 was obtained through solid phase reaction at different sintering pressures, and increasing sintering pressure could accelerate the formation of ZrB2 phase. As the sintering pressure increasing, the fracture strength and toughness of the sintered samples had a similar increasing tendency as the relative density. The better comprehensive properties were obtained at given sintering pressure of 50MPa, and the relative density, fracture strength and toughness reached about 93.4%, 321MPa and 3.3MPa·m1/2, respectively. The SEM analysis shows that the h-BN grains were fine and uniform, and the effect of sintering pressure on grain size was inconspicuous. The distribution of grain is random cross array, and the fracture texture was more obvious with the increase of sintering pressure. The fracture mode of sintered samples remained intergranular fracture mechanism as sintering pressure changed, and the grain refinement, grain pullout and crack deflection helped to increase the mechanical properties.

scholarly journals Synthesis of Ge1−xSnx Alloy Thin Films by Rapid Thermal Annealing of Sputtered Ge/Sn/Ge Layers on Si Substrates

Materials ◽  
2018 ◽  
Vol 11 (11) ◽  
pp. 2248 ◽  
Author(s):  
Hadi Mahmodi ◽  
Md Hashim ◽  
Tetsuo Soga ◽  
Salman Alrokayan ◽  
Haseeb Khan ◽  
...  
Keyword(s):  
Thermal Annealing ◽  
Rapid Thermal Annealing ◽  
Near Infrared ◽  
Annealing Temperature ◽  
Solid Phase ◽  
Infrared Region ◽  
Alloy Formation ◽  
Phase Mixing ◽  
Si Substrates ◽  
Msm Photodetector

In this work, nanocrystalline Ge1−xSnx alloy formation from a rapid thermal annealed Ge/Sn/Ge multilayer has been presented. The multilayer was magnetron sputtered onto the Silicon substrate. This was followed by annealing the layers by rapid thermal annealing, at temperatures of 300 °C, 350 °C, 400 °C, and 450 °C, for 10 s. Then, the effect of thermal annealing on the morphological, structural, and optical characteristics of the synthesized Ge1−xSnx alloys were investigated. The nanocrystalline Ge1−xSnx formation was revealed by high-resolution X-ray diffraction (HR-XRD) measurements, which showed the orientation of (111). Raman results showed that phonon intensities of the Ge-Ge vibrations were improved with an increase in the annealing temperature. The results evidently showed that raising the annealing temperature led to improvements in the crystalline quality of the layers. It was demonstrated that Ge-Sn solid-phase mixing had occurred at a low temperature of 400 °C, which led to the creation of a Ge1−xSnx alloy. In addition, spectral photo-responsivity of a fabricated Ge1−xSnx metal-semiconductor-metal (MSM) photodetector exhibited its extending wavelength into the near-infrared region (820 nm).

Study of solid-phase reaction between CsNO3 AND V2O5 in the molar ratio 6:5

1980 ◽  
Vol 18 (3) ◽  
pp. 469-476 ◽  
Author(s):  
Ľ. Žúrková ◽  
K. Gáplovská ◽  
V. Suchá
Keyword(s):  
Solid Phase ◽  
Molar Ratio ◽  
Solid Phase Reaction ◽  
Phase Reaction

X-Ray and Magnetic Measurements of TmFeTi2O7

2014 ◽  
Vol 215 ◽  
pp. 470-473 ◽  
Author(s):  
Tamara V. Drokina ◽  
German A. Petrakovskii ◽  
Dmitrii A. Velikanov ◽  
Maksim S. Molokeev
Keyword(s):  
Spin Glass ◽  
Solid Phase ◽  
Magnetic Measurements ◽  
Diffraction Method ◽  
Freezing Temperature ◽  
Solid Phase Reaction ◽  
Phase Reaction ◽  
X Ray Diffraction ◽  
X Ray ◽  
History Of

In this paper we are reported about a peculiarity of the crystal structure and the magnetic state of TmFeTi2O7. The compound TmFeTi2O7 has been synthesizedusing the solid-phase reaction method. Using X-ray diffraction method the disorder in the distribution of the iron ions over five nonequivalent crystal sites was observed, also the populations of the iron atoms positions were determined. We show that below Tf = 6 K the magnetization of TmFeTi2O7 depends on the magnetic history of the sample. There are indications for spin glass state. This results allow us to assume the state of spin glass is realized below freezing temperature Tf = 6 K in TmFeTi2O7.

Sign in / Sign up

Export Citation Format

Share Document