scholarly journals Effect of Ohmic Heating and Lye-Salt Concentrations on Quality Characteristics of Tomato Puree

Author(s):  
Sawant Sanket Ramnath ◽  
Pandey Jai Prakash ◽  
Anupama Singh ◽  
Om Prakash
2020 ◽  
Vol 44 (6) ◽  
pp. 543-556
Author(s):  
Bige İNCEDAYI

In this study, the effect of pretreatments (hot water blanching, microwave blanching, and ohmic heating) on the drying kinetics and quality characteristics of red pepper, dried at 60 and 70 °C, was investigated. The drying times varied between 205–290 min, depending on the pretreatment and temperature applied. The drying rate also changed based on the pretreatment and the falling rate period was observed. Four mathematical models were fitted to experimental data and the logarithmic model was found to be the best for all of the samples. Effective moisture diffusivity values obtained from Fick’s second law of diffusion ranged from 6.11 × 10–10 to 9.31 × 10–10 m2 s–1. The total phenolic contents, antioxidant capacities, and red pigment amounts of the dried peppers varied between 6.95 and 9.45 mg GAE g–1dry matter (DM), 2610.43 and 4463.96 mmol AEAC 100 g–1DM, and 184 and 443mg 100 g–1DM, respectively. Rehydration ability of pretreated samples was similar to or slightly lower than that of the untreated samples. As a result, it can be suggested that ohmic heating before drying at a temperature of 70 °C could be a promising alternative pretreatment to decrease drying time and produce high-quality dried red pepper.


2018 ◽  
Vol 99 (5) ◽  
pp. 2589-2595 ◽  
Author(s):  
Serdal Sabanci ◽  
Mutlu Cevik ◽  
Omer F Cokgezme ◽  
Hasan Yildiz ◽  
Filiz Icier

2019 ◽  
Vol 122 (1) ◽  
pp. 75-86
Author(s):  
Oluseyi Moses Ajayi ◽  
Wayne Martindale ◽  
Mark Swainson

Purpose The purpose of this paper is twofold: first, it aims to investigate how salt and sugar reduction in foods due to the pressure from the emerging food regulations will affect the physico-electrical properties (PEPs) of orange juice and tomatoes during a selected PEP-dependent thermal processing. Second, the authors are keen to understand how variations in salt and sugar ingredients will affect the time-temperature processing requirements. Design/methodology/approach PEPs of the samples (orange juice and tomatoes) were measured using the KD2 thermal analyser and RS conductivity metre. Both samples with varying salt and sugar levels were subjected to ohmic heating processing using a 10 kW ohmic heater. Dehydration rates and processing times for pasteurisation were obtained. Findings Electrical conductivity increases with added salt in tomato puree but decreases with added sugar in orange juice. Statistical evidence confirmed significant changes in heating rates and processing times of tomatoes and orange juice as their relevant salt and sugar levels change. Reduction in salt content in tomato puree led to increase in time and energy for the thermal processes. While reduction in added sugar in orange juice results led to reduction in processing time and energy requirement for the processing operation. Research limitations/implications The study is limited to small change in salt and sugar variations in order to reflect recommended limits. There were therefore no significant changes in thermal conductivity for the range investigated. Also this study is focussed on two food products. Practical implications Current pressure on the need to reduce salt and sugar in foods necessitates research to increase food processing industry insight into the process and product impacts of such recipe changes, with particular regard to processing efficiency and product safety and quality. Originality/value This study represents an attempt to understand the impact of salt and sugar variations on properties and processing requirements of tomato puree and orange juice.


2013 ◽  
Vol 58 (3) ◽  
pp. 659-662 ◽  
Author(s):  
K. Gawdzińska

Abstract In this paper it is stated, that a set of quality features of metal matrix composite castings differs from the same set for castings of classic materials, although some features are common for both of these material groups. These features (pertaining to a set of quality characteristics of composite castings) have been named as specific, they have not been determined yet and a description of material quality should be performed (according to the qualitology) on a principle of description of quality characteristics of this product. Therefore, this set of features has been determined. It was proposed to add the following characteristics to the set of specific features of composite castings quality: matrix material, reinforcement material, binding between components and porosity of the composite casting. In this set a sub-set of quality characteristics of composite castings was also determined.


2020 ◽  
Vol 21 (1) ◽  
pp. 15-23
Author(s):  
Sang-Guen Oh ◽  
Jae-Young Lee ◽  
Jae-Woon Jung ◽  
Ju-Tae Song ◽  
Sang-Yun You ◽  
...  

Sign in / Sign up

Export Citation Format

Share Document