Effect of isothermal heat treatment and thermal stretching on the properties of crystalline poly (arylene ether nitrile)

2021 ◽  
pp. 110335
Author(s):  
Chenjiang Wu ◽  
Linsen Zuo ◽  
Lifen Tong ◽  
Xiaobo Liu
Keyword(s):  
Heat Treatment ◽  
Isothermal Heat Treatment ◽  
Arylene Ether

Single-layer submicron-thick BaTiO3 coatings from poly(vinylpyrrolidone)-containing sols: Gel-to-ceramic film conversion, densification, and dielectric properties

2001 ◽  
Vol 16 (11) ◽  
pp. 3116-3123 ◽  
Author(s):  
Hiromitsu Kozuka ◽  
Atsushi Higuchi
Keyword(s):  
Heat Treatment ◽  
Condensation Reaction ◽  
Single Layer ◽  
Dip Coating ◽  
Single Step ◽  
Dielectric Constants ◽  
Isothermal Heat Treatment ◽  
Coating Films ◽  
Ceramic Film ◽  
C Decomposition

BaTiO3-coating films were prepared from a solution containing poly(vinylpyrrolidone) (PVP) of molar composition Ba(CH3COO)2:Ti(OC2H5)4:PVP:CH3COOH:H2O: C2H5OH = 1:1:0.5:27:4:5, via nonrepetitive, single-step dip-coating. The gel films were found to be converted into BaTiO3 films via evaporation of the solvent and CH3COOH below 210 °C, decomposition of PVP at 210–360 °C, decomposition of CH3COO− below 440 °C, and crystallization at 500–610 °C. The decomposition of PVP was accompanied by the progress of the condensation reaction, which resulted in significant reduction in film thickness. When the gel films were heated isothermally at 700 °C, crack-free BaTiO3 films as thick as 0.9 μm were obtained. When the gel films were heated isothermally at 360 °C and then at 700 °C, the film became denser. Higher dielectric constants around 290 were found for the film that underwent the isothermal heat treatment at 360 °C. A slower rate of PVP decomposition was thought to be the key for the film densification.

scholarly journals Influence of Microstructure on Mechanical Properties of Bainitic Steels in Railway Applications

Metals ◽  
2019 ◽  
Vol 9 (7) ◽  
pp. 778 ◽  
Author(s):  
Omid Hajizad ◽  
Ankit Kumar ◽  
Zili Li ◽  
Roumen H. Petrov ◽  
Jilt Sietsma ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Mechanical Behavior ◽  
Mechanical Performance ◽  
Electron Backscatter Diffraction ◽  
Bainitic Ferrite ◽  
Contact Fatigue ◽  
Rolling Contact ◽  
Uniaxial Tensile ◽  
Isothermal Heat Treatment

Wheel–rail contact creates high stresses in both rails and wheels, which can lead to different damage, such as plastic deformation, wear and rolling contact fatigue (RCF). It is important to use high-quality steels that are resistant to these damages. Mechanical properties and failure of steels are determined by various microstructural features, such as grain size, phase fraction, as well as spatial distribution and morphology of these phases in the microstructure. To quantify the mechanical behavior of bainitic rail steels, uniaxial tensile experiments and hardness measurements were performed. In order to characterize the influence of microstructure on the mechanical behavior, various microscopy techniques, such as light optical microscopy (LOM), scanning electron microscopy (SEM) and electron backscatter diffraction (EBSD), were used. Three bainitic grades industrially known as B360, B1400 plus and Cr-Bainitic together with commonly used R350HT pearlitic grade were studied. Influence of isothermal bainitic heat treatment on the microstructure and mechanical properties of the bainitic grades was investigated and compared with B360, B1400 plus, Cr-Bainitic and R350HT in as-received (AR) condition from the industry. The results show that the carbide-free bainitic steel (B360) after an isothermal heat treatment offers the best mechanical performance among these steels due to a very fine, carbide-free bainitic microstructure consisting of bainitic ferrite and retained austenite laths.

scholarly journals Significantly fast spinodal decomposition and inhomogeneous nanoscale martensitic transformation in Ti–Nb–O alloys

2020 ◽  
Vol 321 ◽  
pp. 11049
Author(s):  
Yuya ISHIGURO ◽  
Yuhki TSUKADA ◽  
Toshiyuki KOYAMA
Keyword(s):  
Heat Treatment ◽  
Martensitic Transformation ◽  
Spinodal Decomposition ◽  
Treatment Temperature ◽  
Phase Field Method ◽  
Isothermal Heat Treatment ◽  
Phase Decomposition ◽  
Rate Condition ◽  
Continuous Cooling ◽  
Β Phase

The β phase spinodal decomposition during continuous cooling in Ti‒Nb‒O alloys is investigated by the phase-field method. Addition of only a few at.%O to Ti‒23Nb (at.%) alloy remarkably increases the driving force of the β phase spinodal decomposition. During isothermal heat treatment at 1000 K and 1100 K in Ti‒23Nb‒3O (at.%) alloy, the β phase separates into β1 phase denoted as (Ti)1(O, Va)3 and β2 phase denoted as (Ti, Nb)1(Va)3, resulting in the formation of nanoscale concentration modulation. The phase decomposition progresses in 0.3‒20 ms. In Ti‒23Nb‒XO alloys (X = 1.0, 1.2, 2.0), the spinodal decomposition occurs during continuous cooling with the rate of 500 K s‒1, indicating that the spinodal decomposition occurs during water quenching in the alloys. It is assumed that there is a threshold value of oxygen composition for inducing the spinodal decomposition because it does not occur during continuous cooling in Ti‒23Nb‒0.6O (at.%) alloy. The concentration modulation introduced by the β phase decomposition has significant effect on the β→α” martensitic transformation. Hence, it seems that for controlling microstructure and mechanical properties of Ti‒Nb‒O alloys, careful control of heat treatment temperature and cooling rate condition is required.

Modeling of Dual-Phase Grain Structure in Ti-6Al-4V during Isothermal and Non-Isothermal Heat Treatment by Using Cellular Automata

2013 ◽  
Vol 753 ◽  
pp. 353-356
Author(s):  
Alfred Krumphals ◽  
Cecilia Poletti ◽  
Fernando Warchomicka ◽  
Martin Stockinger ◽  
Christof Sommitsch
Keyword(s):  
Heat Treatment ◽  
Grain Size ◽  
Cellular Automata ◽  
Isothermal Holding ◽  
Equilibrium Phase ◽  
Beta Phase ◽  
Grain Structure ◽  
Isothermal Heat Treatment ◽  
Dual Phase ◽  
Two Phase

In the titanium alloy Ti-6Al-4V the dual-phase grain structure, which forms during thermo-mechanical processing, is of high importance due to its effect on the mechanical properties. In general the most significant microstructural parameters are the amount of alpha and beta phase as well as their grain size. For this reason a new cellular automata method (CA) was developed to predict the evolving grain structure during isothermal and non-isothermal heat treatment. The probabilistic CA model is based on the diffusion controlled movement of grain and phase boundaries. During temperature changes an algorithm is adjusting alpha and beta phase fraction to maintain equilibrium phase values. Hence, the CA is capable to calculate grain coarsening as well as grain growth and shrinking in the two-phase area while heating and isothermal holding at forging temperature. The initial microstructure can be imported form virtual created microstructures, real micrographs and EBSD-images. The results are mean grain diameters, grain size distributions and virtually simulated microstructures which can be easily compared with real micrographs. The predicted microstructures are showing a good correlation to data in literature and experimental results.

High Indentation Resistance of Aluminum Borate Based Glass-Ceramics

2013 ◽  
Vol 545 ◽  
pp. 3-7
Author(s):  
Pat Sooksaen ◽  
Pisud Prasertcharoensuk ◽  
Jiraporn Damnernsawat ◽  
Nimit Pattamawitayanimit
Keyword(s):  
Heat Treatment ◽  
Glass Melting ◽  
Isothermal Holding ◽  
Surface Hardness ◽  
Glass Ceramics ◽  
Isothermal Heat Treatment ◽  
Aluminum Borate ◽  
Holding Period ◽  
Heating And Cooling ◽  
Heat Treated

This study investigated the bulk crystallization of 54B2O3-19SiO2-17Al2O3-5BaO-5MgO (mol%) glass. Melting was carried out at 1500°C for 1 h using a bottom-load electric furnace. The glass melt was cast into a block and annealed at 500°C for 2 h. Isothermal heat treatment was carried out at 1100°C for 2, 4, 8, 16, 32 h to form bulk crystallized glass-ceramics using a heating and cooling rate of 5°C/min. Phases present in the glass-ceramic samples were studied by x-ray diffraction. Crystalline Al4B2O9 and Al18B4O33 were the main phases and the phase stability depended on the isothermal time. Microstructures were observed by a scanning electron microscope. The size of aluminum borate whiskers/rods tend to increase with longer isothermal holding period. The whisker/ rod-like crystals uniformly oriented throughout the microstructure in all heat treated samples. This led to interlocking microstructure and hence an increase in hardness and fracture toughness. Glass-ceramics synthesized at longer heat treatment times resulted in an increase in the surface hardness and shorter path length at the corner of the diamond pyramid-shaped indenter. Glass-ceramics synthesized in this study can be applied as high temperature resistant machinable materials because their microstructures can resist micro-cracking upon indentation.

Sign in / Sign up

Export Citation Format

Share Document