Effects of Temperature and Grain Size on Diffusivity of Aluminium: Electromigration Experiment and Molecular Dynamic Simulation

Understanding the atomic diffusion features in metallic material is significant to explain the diffusion-controlled physical processes. In this paper, using electromigration experiments and molecular dynamic (MD) simulations, we investigate the effects of grain size and temperature on the self-diffusion of polycrystalline aluminum (Al). The mass transport due to electromigration are accelerated by increasing temperature and decreasing grain size. Magnitudes of effective diffusivity (Deff) and grain boundary diffusivity (DGBs) are experimentally determined, in which the Deff changes as a function of grain size and temperature, but DGBs is independent of the grain size, only affected by the temperature. Moreover, MD simulations of atomic diffusion in polycrystalline Al demonstrate those observations from experiments. Based on MD results, the Arrhenius equation of DGBs and empirical formula of the thickness of grain boundaries at various temperatures are obtained. In total, Deff and DGBs obtained in the present study agree with literature results, and a comprehensive result of diffusivities related to the grain size is presented.

Influence of synthesis parameters and thermal annealing on grain size of polycrystalline aluminum thin film

The thin polycrystalline aluminium films were synthesized on monocrystalline silicon substrates by ion-plasma sputtering. The synthesis was carried out at temperatures of 80 and 160°C and deposition rate of 10 and 110 nm/min. As-deposited films were annealed for 15 h at 550°C. The morphology of aluminium films before and after annealing was obtained using SEM images. The surfaces of as-deposited Al thin films, synthesized at high temperature, were uneven, while for low temperature films they were smooth enough with Al hillocks on the top of the film. After thermal annealing, morphology of the films was changed slightly. XRD patterns were obtained to calculate the average Al grain size of as-deposited and annealed films. The XRD analysis showed that an increase in the synthesis temperature leads to an increase in the average grain size from 50 to 84 nm and that increase in the rate of Al film synthesis leads to an increase in the average grain size from 50 to 63 nm. As the result of annealing, the average grain size increased for all samples and the final meaning was from 78 to 140 nm.

Investigation on Plastic Flow Behaviors of FCC Polycrystalline Aluminum under Pre-Cyclic Tension-Compression Loading: Experiments and Crystal Plasticity Modeling

The plastic flow behaviors of FCC polycrystalline aluminum after pre-cyclic tension-compression deformation are mainly investigated in tension–torsion stress space by the physically based crystal plasticity model introducing a back-stress. A global finite element model (GFEM) constructed of sufficient grains was established to simulate the same-size thin-walled tube specimen constrained and loaded as the experiments of yield surfaces. The computational results showed that the shape of subsequent yield surfaces and the plastic flow directions directly depended on the given offset strain levels and the applied re-loading paths under different pre-cyclic deformations. The angle deviation between the plastic flow direction and the theoretical orthogonal direction further indicated that there was a large difference between them in the inverse pre-straining direction, but the difference was negligible in the pre-straining direction. From the influence of the anisotropic evolution of the subsequent yield surfaces on plastic flow, we found that the plastic normality rule followed the smooth yield locus; conversely, the significant non-associated flow was attributed to the distorted yield locus. Furthermore, it was also demonstrated that the anisotropic evolution and the plastic flow trend of the subsequent yield surfaces obtained by experiments can be better reproduced by the crystal plasticity model.

Estimation via Laser Ultrasonics of the Ultrasonic Attenuation in a Polycrystalline Aluminum Thin Plate Using Complex Wavenumber Recovery in the Vicinity of a Zero-Group-Velocity Lamb Mode

In this paper, we present a method to recover the complex wavenumber dispersion relations using spatial Laplace transform from experimental spatiotemporal signals measured by laser ultrasonic technique. The proposed method was applied on zero-group-velocity Lamb modes in order to extract the ultrasonic attenuation in a polycrystalline aluminum plate of about 70 μm thickness. The difference between the experimental and theoretical Laplace Fourier transforms was minimized in the least square sense to extract the complex amplitudes and complex wavenumbers of the modes at about 40 MHz. The experimental results were compared to values reported in the literature that were measured by other means and those estimated by using the quality factor extracted from a single temporal signal.

Preparation of silicon and aluminum nanoparticles in an aqueous solution

The interest in nanomaterials is due to a significant change in their physical properties compared to massive materials. Changes in the physical and chemical properties of particles containing several hundred or thousands of atoms are determined by changes in the density of electronic states.Aqueous solutions of aluminum and silicon nanoparticles were obtained by laser ablation. Pulsed laser treatment was performed in the mode of double pulses in distilled water. The invested energy was: for aluminum 1000–1500 J, the exposure time is 10–25 min., for silicon-50–1000 J with exposure times from 1 to 10 min.The features of the morphology of the obtained particles, as well as the surface of polycrystalline aluminum and silicon craters, were determined by scanning electron microscopy. It is shown that an ensemble of particles of different sizes from 20 nm to 2.0 microns is formed. Some aluminum particles are cut, which allows us to talk about their cristallinity. It is shown that the structure of the target surface after laser exposure consists of grains separated from each other by thermal etching grooves, since the evaporation of the material occurs primarily along the grain boundaries.