Implementation and characterisation of a sterilisation module consisting of novel 265 nm UVC LED packages

To efficiently fight against the COVID-19 pandemic, a sterilisation module using 265 nm UVC LED packages was developed. In this paper, the performance of the sterilisation module in terms of irradiance uniformity, junction temperature increase and sterilisation efficiency were characterised. The irradiance uniformity fluctuation across the four corners and the centre point in a 130 mm × 130 mm area was below 10%, exhibiting good uniformity. Uniform irradiance was important to achieve consistent sterilisation, which was the primary difference between the UVC LED package developed and commercial UVC LED packages. Key to achieving uniform irradiance was the structure, consisting of a stacked silicon reflector and a secondary optical lens designed by ray tracing simulation. The junction temperature increase of the 265 nm UVC LED package driving at 200 mA was only 28°C, sufficiently low to exhibit better reliability and performance. A 99.99% sterilisation efficiency on E. coli bacteria was achieved within one minute with UV dosage of 2.7 mJ/cm2 at 200 mA driving current. From the results, the novel 265 nm UVC LED package was a time-efficient solution for disinfection purposes.

Impact of the thickness of the wall of optical lenses on the production process stability

The article compares the stability of the production process of plastic optical lenses produced by the injection molding process. Moreover, it evaluates the effects caused by using very thick walls and very thin walls in plastic optical lenses. The injection process are divided into three fundamental stages. The first is the injection of plastic into the mold itself (filling). During this phase, 95–99% of the cavity volume is filled. The second phase is the so-called after-pressure, where the remaining cavity spaces are filled, and the part reaches dimensional stability. The last stage is called cooling. During the final phase, the element is solidified and becomes dimensionally stable in lower temperatures. In the current work, the authors compare the lenses that differ only in the maximum wall thickness. In the experiments, the conditions of changing pressure and injection speed were simulated. During injection, slight changes in the injection parameters may occur due to the random external influences. Those influences include the change in ambient air temperature, voltage fluctuations in the electrical system, machine vibrations, imperfect homogeneity of the material used, etc. The common process parameters that the organization uses by default were used as a basis. The after-pressure and injection pressure were changed to 102%, 105%, 98%, and 95% in the experiments. The results evaluate the proportion of non-conforming products (scrap) that appertain to each change in the parameters of production. The research proves the dependence between the thickness of the lens wall and the stability of the process. Although a higher total waste is expected for thick-walled lenses, the knowledge of the stability of the process in the production of lenses has not yet been recorded though it is a significant indicator for the production planning. It is known that a lower process stability is expected based on the design for these types of elements, and the researrchers were able to take measures to eliminate this risk and thus reduce the total waste and other negative impacts on production. Modifications to the mold can also achieve some improvement in this condition. The first step is to expand the cross-section of the inlet channel gate. The pressure is transmitted to the cavity through this cross-section. Its enlargement ensures a more even distribution of the pressure in the entire volume of the part. Another way to facilitate production is to guarantee optimal cooling of the cavity. It can be achieved by placing the cavity away from the hot runner system so that the cooling can be evenly distributed around each side of the part. The last way to solve the problem of collapse is to create a counter-deformation in the mold. That is to enlarge the cavity so that the lens sinks into the desired shape. These measures may include preventive debugging of the mold for multiple presses in case the press needs to be changed and preferably placing such elements on newer injection molding machines where parameters are less likely to fluctuate and avoiding moving such molds to presses for which they have not been debugged unless necessary. The work aims to prove the dependence between the thickness of the optical lens and the stability of the injection process. While waste percentage, cycle time, and other parameters are considered and quantified at the design stage of the optical lens, process stability has not yet been quantified. Proving the dependence between the above-mentioned phenomena will allow predicting the process stability of new lens designs more precisely.

On the History, Presence, and Future of Optics Manufacturing

In 1850, Austen Henry Layard discovered an approximately 3000-year-old, simple optical lens in Nimrud, Northern Iraq—the Nimrud lens, aka the Layard lens [...]