electro deposition
Recently Published Documents


TOTAL DOCUMENTS

666
(FIVE YEARS 124)

H-INDEX

30
(FIVE YEARS 4)

Energies ◽  
2022 ◽  
Vol 15 (2) ◽  
pp. 542
Author(s):  
Benjamin Udo Emmel ◽  
Kamila Maria Gawel ◽  
Mohammad Hossain Bhuiyan ◽  
Malin Torsæter ◽  
Laura Edvardsen

Reservoir formation waters typically contain scaling ions which can precipitate and form mineral deposits. Such mineral deposition can be accelerated electrochemically, whereby the application of potential between two electrodes results in oxygen reduction and water electrolysis. Both processes change the local pH near the electrodes and affect the surface deposition of pH-sensitive minerals. In the context of the plugging and abandonment of wells, electrochemically enhanced deposition could offer a cost-effective alternative to the established methods that rely on setting cement plugs. In this paper, we tested the scale electro-deposition ability of six different formation waters from selected reservoirs along the Norwegian continental shelf using two experimental setups, one containing CO2 and one without CO2. As the electrochemical deposition of scaling minerals relies on local pH changes near the cathode, geochemical modelling was performed to predict oversaturation with respect to the different mineral phases at different pH values. In a CO2-free environment, the formation waters are mainly oversaturated with portlandite at pH > 12. When CO2 was introduced to the system, the formation waters were oversaturated with calcite. The presence of mineral phases was confirmed by powder X-ray diffraction (XRD) analyses of the mineral deposits obtained in the laboratory experiments. The geochemical-modelling results indicate several oversaturated Mg-bearing minerals (e.g., brucite, dolomite, aragonite) in the formation waters but these, according to XRD results, were absent in the deposits, which is likely due to the significant domination of calcium-scaling ions in the solution. The amount of deposit was found to be proportional to the concentration of calcium present in the formation waters. Formation waters with a high concentration of Ca ions and a high conductivity yielded more precipitate.


Crystals ◽  
2021 ◽  
Vol 12 (1) ◽  
pp. 37
Author(s):  
Chuancang Zhou ◽  
Feipeng Zhang ◽  
Hongyu Wu

To improve the electrocatalytic properties for hydrogen evolution reactions, strategies need to be adopted, such as increasing specific surface area and active site, as well as decreasing interface energy. Herein, we report the preparation of FeP on carbon cloth using a two-step process of hydrothermal and phosphating. Otherwise, to utilize the excellent catalytic performance of Pt and decrease consumption of Pt, the hyperdispersed Pt nanoparticles for the sake of modifying transition-metal phosphides film were designed and fabricated. Finally, 3D FeP-Pt/CC was successfully prepared by means of electro-deposition using three electrodes. The crystalline structure, surface morphology and elemental composition of the synthesized samples have been investigated by X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), scanning electron microscopy (SEM) and energy dispersive X-ray analysis (EDS). The XRD results show that the as-prepared products are of orthorhombic FeP structure, and EDS results indicate that there exist Pt elements in 3D FeP-Pt/CC. The electrocatalytic performances were evaluated by, such as linear scan voltammetry, tafel plots and electrochemical impedance spectroscopy on electrochemical workstations. These results show that the FeP-Pt/CC exhibit a current density of 10 mA·cm−2 at an over-potential of 58 mV for HER in 0.5 M H2SO4, which is very close to the values of 20%Pt/C which was previously reported. FeP-Pt/CC has excellent durability.


Author(s):  
You-gang Li ◽  
Shan-shan Liu ◽  
Chang-hong Wang ◽  
Tao Luo ◽  
Chang-liu Xiang ◽  
...  

2021 ◽  
pp. 134389
Author(s):  
Wanlong Wu ◽  
Xianpeng Yang ◽  
Kuo Wang ◽  
Cuicui Li ◽  
Xiang Zhang ◽  
...  

2021 ◽  
Vol 2114 (1) ◽  
pp. 012077
Author(s):  
N Salam ◽  
M A. Jaleel

Abstract In this paper, we succeeded in obtaining a Ni/SiC nano composite coating using conventional electro deposition by adding different amount of SiC nanoparticles to a nickel-watt bath to be co-deposited. The effect of electro deposition conditions was studied by changing the amount of SiC nanoparticles in the nano composite, and the deposition current density which affects on the participation of SiC nanoparticles in the coating. The morphology and mechanical properties of the electrodeposited nano-composite were studied. The wear behavior of the nano-composite coatings was evaluated on a ball-on-disk test. It was found that the increased micro hardness and wear resistance of the nano-composite coatings increased with increasing content of the SiC nano-particulate in bath.


Polymers ◽  
2021 ◽  
Vol 13 (23) ◽  
pp. 4109
Author(s):  
Azhar Equbal ◽  
Asif Equbal ◽  
Zahid A. Khan ◽  
Irfan Anjum Badruddin ◽  
Mohamed Bashir Ali Bashir ◽  
...  

In the present study, cylindrical ABS P400 polymer parts (diameter 6.5 mm) to be used as die-sinking EDM (electric discharge machining) novel electrodes were fabricated using a fused deposition modeling (FDM) process. To meet the conductivity requirement in EDM, ABS parts were metallized using an innovative method that comprised putting aluminum–charcoal (Al–C) on them followed by their copper electroplating. Real-time EDM of the mild steel workpiece was performed using novel electrodes, and machining performance of the electrodes, measured in terms of dimensional accuracy, i.e., change in diameter (ΔD) and change in depth (ΔH) of the cavity, under varying levels of three EDM factors, i.e., current (I), pulse on time (Ton), and pulse off time (Toff), was investigated. Machining results were analyzed using analysis of variance (ANOVA), perturbation graphs, and 3D surface plots. The optimal setting of the EDM parameters for minimizing ΔD and ΔH was determined using the desirability function approach. The suitability of the novel electrodes for EDM was ascertained by comparing their machining results with those of solid copper (SC) electrodes and electrodes fabricated by FDM and metallized using the electro-deposition method (FDM-EM), already reported in the literature, under similar machining conditions. From the results, it was found that ΔD and ΔH were less when EDM was performed using novel electrodes.


Sign in / Sign up

Export Citation Format

Share Document