Morphology of nylon 6/acrylonitrile-butadiene-styrene blends compatibilized by a methyl methacrylate/maleic anhydride copolymer

2003 ◽  
Vol 90 (13) ◽  
pp. 3512-3518 ◽  
Author(s):  
E. M. Araújo ◽  
E. Hage ◽  
A. J. F. Carvalho
Keyword(s):  
Maleic Anhydride ◽  
Methyl Methacrylate ◽  
Acrylonitrile Butadiene Styrene ◽  
Nylon 6 ◽  
Maleic Anhydride Copolymer ◽  
Butadiene Styrene

Effect of Compatibilizer and Flexibilizer on the Mechanical Properties of Acrylonitrile-Butadiene-Styrene)/Poly(Methyl Methacrylate) Blends

2014 ◽  
Vol 496-500 ◽  
pp. 317-321
Author(s):  
Shou Hai Wang ◽  
Jun Gao ◽  
Gu Ren Fei ◽  
Ping Zhang ◽  
Jun Huang ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Maleic Anhydride ◽  
Methyl Methacrylate ◽  
Acrylonitrile Butadiene Styrene ◽  
Screw Extruder ◽  
Polyolefin Elastomer ◽  
Twin Screw ◽  
Orthogonal Tests ◽  
Butadiene Styrene

Acrylonitrile-butadiene-styrene (ABS) / polymethyl methacrylate (PMMA) with the addition of maleic anhydride grafted polystyrene (KT-5) and polyolefin elastomer (POE) were melt processed in a co-rotating twin-screw extruder. The effect of KT-5 and POE content on the mechanical properties of ABS/PMMA was investigated. Experiment results indicate that KT-5 can improve the tensile strength and the composites are toughened effectively as the addition of POE. According to Orthogonal tests, it demonstrates that POE ha a greater effect on the blends than KT-5, and there exist no obvious interactivity between the two components.

scholarly journals A Practical Manner To GTR Recycling in Waste HDPE/ABS

2021 ◽  
Author(s):  
Csilla Varga ◽  
Balázs Heller ◽  
Lilla Simon-Stőger ◽  
Éva Makó
Keyword(s):  
Mechanical Properties ◽  
Maleic Anhydride ◽  
Acrylonitrile Butadiene Styrene ◽  
Mechanical Tests ◽  
X Ray Diffraction ◽  
Ground Tire Rubber ◽  
Industrial Practice ◽  
X Ray ◽  
Maleic Anhydride Copolymer ◽  
Butadiene Styrene

Abstract Waste high-density polyethylene (w-HDPE)/ acrylonitrile-butadiene-styrene (ABS)/ground tire rubber (GTR) have been melt blended by two-roll milling. Ternary blends of w-HDPE/ABS/GTR have been observed to be incompatible in the composition range studied which revealed in the deteriorated mechanical properties. Two main types of compatibilizers such as an olefin-maleic anhydride copolymer based one synthesized by the authors and a commercial maleic anhydride grafted polypropylene (MA-g-PP) have been chosen for enhancing compatibility between the components ergo the mechanical properties. For characterizing tensile and impact properties of the blends mechanical tests have been carried out besides the scanning electron microscopy (SEM), X-ray diffraction and Fourier transform infrared spectroscopy. The most advantageous result in industrial practice can be that the experimental additive allows to apply higher GTR concentration ergo gives the opportunity to recycle higher level of GTR.

Flow Behavior of Composites of PA6/Kaolin Nanoparticles

2014 ◽  
Vol 703 ◽  
pp. 45-50
Author(s):  
Chao Wang ◽  
Ying Chun Li ◽  
Guo Sheng Hu
Keyword(s):  
Mechanical Properties ◽  
Flow Behavior ◽  
Acrylonitrile Butadiene Styrene ◽  
Nylon 6 ◽  
Mechanical Analysis ◽  
Melt Blending ◽  
Styrene Maleic Anhydride ◽  
The Impact ◽  
Scanning Electron ◽  
Butadiene Styrene

The blends of Nylon 6/Acrylonitrile-Butadiene-Styrene (ABS) with styrene-maleic anhydride (SMA) was prepared by melt blending as the compatilizer. Mechanical properties, dynamic mechanical analysis (DMA) and fracture appearances were determined. It was found that the impact and tensile strength firstly increased and then decreased along with the increase of the SMA content. The properties reached maximum values when the content of SMA was 1.5%. The results of DMA and scanning electron microscope (SEM) indicated that the addition of SMA can effectively enhance the compatibility of Nylon 6 and ABS. Key words: Nylon 6, ABS, SMA, blends, modification

Sign in / Sign up

Export Citation Format

Share Document