Effects of Fly Ash Content and Curing Age on High Temperature Residual Compressive Strength of Strain-Hardening Cementitious Composites

2021 ◽  
pp. 3-12
Author(s):  
Dhanendra Kumar ◽  
Amr Ashraf Soliman ◽  
Ravi Ranade
Keyword(s):  
Compressive Strength ◽  
High Temperature ◽  
Fly Ash ◽  
Strain Hardening ◽  
Ash Content ◽  
Cementitious Composites ◽  
Residual Compressive Strength ◽  
Curing Age

Research on Barite Concrete Mixed with Fly Ash

2013 ◽  
Vol 275-277 ◽  
pp. 2107-2111
Author(s):  
Qiu Lin Zou ◽  
Jun Li ◽  
Zhen Yu Lai
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Compressive Strength ◽  
High Temperature ◽  
Fly Ash ◽  
Apparent Density ◽  
Cycle Times ◽  
Residual Compressive Strength ◽  
Temperature Performance

Barite concrete with density grade of 3 and strength grade of C30 was prepared by mixing with different fineness of fly ash. The workability, mechanical properties and long-term high temperature performance of the prepared barite concrete were researched. Results show that the workability of barite concrete is improved by mixing with fly ash, and no segregation of mixture has been observed. The apparent density and 3d, 28d compressive strength of barite concrete are decreased obviously after mixing with fly ash. But with the increasing of the fineness of fly ash, the apparent density and 3d, 28d compressive strength of barite concrete have a slight increase. High temperature residual compressive strength is decreased with the increasing of temperature. The cycle times of heat treatment at 400°C only has a little effect on residual compressive strength of barite concrete.

Development of self-compacting strain-hardening cementitious composites by varying fly ash content

2017 ◽  
Vol 149 ◽  
pp. 103-110 ◽  
Author(s):  
Chang Lin ◽  
Obada Kayali ◽  
Evgeny V. Morozov ◽  
David J. Sharp
Keyword(s):  
Fly Ash ◽  
Strain Hardening ◽  
Ash Content ◽  
Cementitious Composites

scholarly journals Influence of curing age on high-temperature properties of additive manufactured geopolymer mortar

2020 ◽  
Vol 218 ◽  
pp. 03019
Author(s):  
Xiaohong Yin ◽  
Xiaodong Wang ◽  
Yuan Fang ◽  
Zhu Ding
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
High Temperature ◽  
Elevated Temperature ◽  
Fly Ash ◽  
Flexural Strength ◽  
High Temperature Properties ◽  
Before And After ◽  
3D Printed ◽  
Curing Age

Some researches have been conducted on the application of geopolymer in 3D printing. However, there is no publication about the high-temperature properties of 3D printed geopolymer made from fly ash, slag, and metakaolin. This paper presents the experimental research on the mechanical properties of 3D printed geopolymer after being exposed to elevated empratures. The effects of curing age on high-temperature properties are analyzed. The heating temperasures were 300 °C, 600 °C, and 900 °C, and the holding time was one hour. After exposure to temperatures, the flexural strength of 3D printed geopolymer exhibited different change trends with increasing curing age for different exposure temperatures. Before and after exposure to elevated temperature, the 3D printed geopolymer experienced significant anisotropic compressive strengths. The change trends of compressive strength at different exposure temperatures wit hincreasing curing ages were different from each other on different loading directions.

Engineered/strain-hardening cementitious composites (ECC/SHCC) with a compressive strength over 210 MPa

2021 ◽  
pp. 100775
Author(s):  
Bo-Tao Huang ◽  
Ke-Fan Weng ◽  
Ji-Xiang Zhu ◽  
Yu Xiang ◽  
Jian-Guo Dai ◽  
...  
Keyword(s):  
Compressive Strength ◽  
Strain Hardening ◽  
Cementitious Composites ◽  
Engineered Strain

Effects of Elevated Temperatures on the Compressive Strength of HFCC

2011 ◽  
Vol 261-263 ◽  
pp. 416-420 ◽  
Author(s):  
Fu Ping Jia ◽  
Heng Lin Lv ◽  
Yi Bing Sun ◽  
Bu Yu Cao ◽  
Shi Ning Ding
Keyword(s):  
Compressive Strength ◽  
Elevated Temperature ◽  
Fly Ash ◽  
Room Temperature ◽  
Elevated Temperatures ◽  
Relative Strength ◽  
Ordinary Concrete ◽  
Residual Compressive Strength ◽  
Fly Ash Concrete ◽  
The Relationship

This paper presents the results of elevated temperatures on the compressive of high fly ash content concrete (HFCC). The specimens were prepared with three different replacements of cement by fly ash 30%, 40% and 50% by mass and the residual compressive strength was tested after exposure to elevated temperature 250, 450, 550 and 650°C and room temperature respectively. The results showed that the compressive strength apparently decreased with the elevated temperature increased. The presence of fly ash was effective for improvement of the relative strength, which was the ratio of residual compressive strength after exposure to elevated temperature and ordinary concrete. The relative compressive strength of fly ash concrete was higher than those of ordinary concrete. Based on the experiments results, the alternating simulation formula to determine the relationship among relative strength, elevated temperature and fly ash replacement is developed by using regression of results, which provides the theoretical basis for the evaluation and repair of HFCC after elevated temperature.

Physical Properties of Cement Mortar Containing Waste Ash

2015 ◽  
Vol 804 ◽  
pp. 129-132
Author(s):  
Sumrerng Rukzon ◽  
Prinya Chindaprasirt
Keyword(s):  
Compressive Strength ◽  
Fly Ash ◽  
Rice Husk ◽  
Rice Husk Ash ◽  
Cement Mortar ◽  
Ash Content ◽  
Water Requirement ◽  
Test Results ◽  
Pozzolanic Material ◽  
Materials Used

This research studies the potential for using waste ash from industrial and agricultural by-products as a pozzolanic material. Classified fly ash (FA) and ground rice husk ash (RA) were the materials used. Water requirement, compressive strength and porosity of cement mortar were investigated. Test results indicated that FA and RA (waste ash) have a high potential to be used as a good pozzolanic material. The water requirement of mortar mix decreases with the increases in fly ash content. For ground rice husk ash (RA), the water requirement of mortar mix increases with the increases in rice husk ash content. In addition, the reduction in porosity was associated with the increase in compressive strength.

scholarly journals Biofuel Combustion Fly Ash Influence on the Properties of Concrete

2016 ◽  
Vol 7 (5) ◽  
pp. 546-550
Author(s):  
Aurelijus Daugėla ◽  
Džigita Nagrockienė ◽  
Laurynas Zarauskas
Keyword(s):  
Compressive Strength ◽  
Fly Ash ◽  
Portland Cement ◽  
Water Absorption ◽  
Frost Resistance ◽  
Ash Content ◽  
Mineral Admixtures ◽  
Binding Agent ◽  
Materials Used ◽  
Plasticizing Admixture

Cement as the binding agent in the production of concrete can be replaced with active mineral admixtures. Biofuel combustion fly ash is one of such admixtures. Materials used for the study: Portland cement CEM I 42.5 R, sand of 0/4 fraction, gravel of 4/16 fraction, biofuel fly ash, superplasticizer, water. Six compositions of concrete were designed by replacing 0%, 5%, 10%, 15% 20%, and 25% of cement with biofuel fly ash. The article analyses the effect of biofuel fly ash content on the properties of concrete. The tests revealed that the increase of biofuel fly ash content up to 20% increases concrete density and compressive strength after 7 and 28 days of curing and decreases water absorption, with corrected water content by using plasticizing admixture. It was found that concrete where 20% of cement is replaced by biofuel ash has higher frost resistance.

High Volume Slag and Slag-Fly Ash Blended Cement Pastes Containing Nano Silica

2019 ◽  
Vol 967 ◽  
pp. 205-213
Author(s):  
Faiz U.A. Shaikh ◽  
Anwar Hosan
Keyword(s):  
Compressive Strength ◽  
Fly Ash ◽  
Cement Paste ◽  
Ordinary Portland Cement ◽  
Blended Cement ◽  
High Volume ◽  
Ash Content ◽  
Partial Replacement ◽  
Nano Silica ◽  
Cement Pastes

This paper presents the effect of nanosilica (NS) on compressive strength and microstructure of cement paste containing high volume slag and high volume slag-fly ash blend as partial replacement of ordinary Portland cement (OPC). Results show that high volume slag (HVS) cement paste containing 60% slag exhibited about 4% higher compressive strength than control cement paste, while the HVS cement paste containing 70% slag maintained the similar compressive strength to control cement paste. However, about 9% and 37% reduction in compressive strength in HVS cement pastes is observed due to use of 80% and 90% slag, respectively. The high volume slag-fly ash (HVSFA) cement pastes containing total slag and fly ash content of 60% exhibited about 5%-16% higher compressive strength than control cement paste. However, significant reduction in compressive strength is observed in higher slag-fly ash blends with increasing in fly ash contents. Results also show that the addition of 1-4% NS improves the compressive strength of HVS cement paste containing 70% slag by about 9-24%. However, at higher slag contents of 80% and 90% this improvement is even higher e.g. 11-29% and 17-41%, respectively. The NS addition also improves the compressive strength by about 1-59% and 5-21% in high volume slag-fly ash cement pastes containing 21% fly ash+49%slag and 24% fly ash+56%slag, respectively. The thermogravimetric analysis (TGA) results confirm the reduction of calcium hydroxide (CH) in HVS/HVSFA pastes containing NS indicating the formation of additional calcium silicate hydrate (CSH) gels in the system. By combining slag, fly ash and NS in high volumes e.g. 70-80%, the carbon footprint of cement paste is reduced by 66-76% while maintains the similar compressive strength of control cement paste. Keywords: high volume slag, nanosilica, compressive strength, TGA, high volume slag-fly ash blend, CO2 emission.

Sign in / Sign up

Export Citation Format

Share Document