scholarly journals Influence of curing age on high-temperature properties of additive manufactured geopolymer mortar

2020 ◽  
Vol 218 ◽  
pp. 03019
Author(s):  
Xiaohong Yin ◽  
Xiaodong Wang ◽  
Yuan Fang ◽  
Zhu Ding
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
High Temperature ◽  
Elevated Temperature ◽  
Fly Ash ◽  
Flexural Strength ◽  
High Temperature Properties ◽  
Before And After ◽  
3D Printed ◽  
Curing Age

Some researches have been conducted on the application of geopolymer in 3D printing. However, there is no publication about the high-temperature properties of 3D printed geopolymer made from fly ash, slag, and metakaolin. This paper presents the experimental research on the mechanical properties of 3D printed geopolymer after being exposed to elevated empratures. The effects of curing age on high-temperature properties are analyzed. The heating temperasures were 300 °C, 600 °C, and 900 °C, and the holding time was one hour. After exposure to temperatures, the flexural strength of 3D printed geopolymer exhibited different change trends with increasing curing age for different exposure temperatures. Before and after exposure to elevated temperature, the 3D printed geopolymer experienced significant anisotropic compressive strengths. The change trends of compressive strength at different exposure temperatures wit hincreasing curing ages were different from each other on different loading directions.

The Mechanical Properties and Thermal Resistance of Fly Ash Geopolymer Foams

2018 ◽  
Vol 281 ◽  
pp. 175-181
Author(s):  
Hui Teng Ng ◽  
Cheng Yong Heah ◽  
Yun Ming Liew ◽  
Mohd Mustafa Al Bakri Abdullah ◽  
Kamarudin Hussin
Keyword(s):  
Mechanical Properties ◽  
Hydrogen Peroxide ◽  
Compressive Strength ◽  
High Temperature ◽  
Elevated Temperature ◽  
Fly Ash ◽  
Thermal Resistance ◽  
Bulk Density ◽  
Room Temperature ◽  
Heating Up

In the present work, a comparative study of the thermal performance of unfoamed and foamed geopolymers was investigated. The geopolymers were prepared by mixing fly ash with alkali activator (a mixture of sodium hydroxide and sodium silicate). The geopolymer foams were prepared by adding hydrogen peroxide (H2O2, 2wt.% and 4wt.%). The geopolymers were cured at room temperature (29°C) for 24 hours and at 60°C for another 24 hours. The bulk density and compressive strength decreased with increasing H2O2 up to 2wt.% and increased when 4wt.% of H2O2 was added. In order to test the thermal resistance, the geopolymers were heated at elevated temperature (200- 1000°C). Unheated geopolymers showed bulk density and compressive strength in the range of 1.6– 1.7g/cm3 and 15–17MPa, respectively. When heated up to 1000°C, the geopolymers could withstand high temperature without any disintegration and spalling. Both unfoamed and foamed geopolymers showed highest compressive strength at 200°C (17–22MPa). Further decreased in compressive strength was observed upon heating up to 800°C (10–17MPa). The compressive strength regained (14–21MPa) when heated up to 1000°C. The compressive strength was even higher than that recorded at room temperature. In the present work, unfoamed geopolymers showed overall higher thermal resistance than foamed geopolymers.

scholarly journals Assessment of the Rheological and Mechanical Properties of Geopolymer Concrete Comprising Fly Ash and Fluid Catalytic Cracking Residue as Aluminosilicate Precursor

2021 ◽  
Vol 11 (7) ◽  
pp. 3032
Author(s):  
Tuan Anh Le ◽  
Sinh Hoang Le ◽  
Thuy Ninh Nguyen ◽  
Khoa Tan Nguyen
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
Elastic Modulus ◽  
Fly Ash ◽  
Flexural Strength ◽  
Catalytic Cracking ◽  
Fluid Catalytic Cracking ◽  
High Alumina ◽  
Geopolymer Concrete ◽  
Sem Images

The use of fluid catalytic cracking (FCC) by-products as aluminosilicate precursors in geopolymer binders has attracted significant interest from researchers in recent years owing to their high alumina and silica contents. Introduced in this study is the use of geopolymer concrete comprising FCC residue combined with fly ash as the requisite source of aluminosilicate. Fly ash was replaced with various FCC residue contents ranging from 0–100% by mass of binder. Results from standard testing methods showed that geopolymer concrete rheological properties such as yield stress and plastic viscosity as well as mechanical properties including compressive strength, flexural strength, and elastic modulus were affected significantly by the FCC residue content. With alkali liquid to geopolymer solid ratios (AL:GS) of 0.4 and 0.5, a reduction in compressive and flexural strength was observed in the case of geopolymer concrete with increasing FCC residue content. On the contrary, geopolymer concrete with increasing FCC residue content exhibited improved strength with an AL:GS ratio of 0.65. Relationships enabling estimation of geopolymer elastic modulus based on compressive strength were investigated. Scanning electron microscope (SEM) images and X-ray diffraction (XRD) patterns revealed that the final product from the geopolymerization process consisting of FCC residue was similar to fly ash-based geopolymer concrete. These observations highlight the potential of FCC residue as an aluminosilicate source for geopolymer products.

Effect of using magnetic water on the mechanical properties of concrete exposed to elevated temperature

2021 ◽  
Vol ahead-of-print (ahead-of-print) ◽  
Author(s):  
Wasim Barham ◽  
Ammar AL-Maabreh ◽  
Omar Latayfeh
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Compressive Strength ◽  
Elevated Temperature ◽  
Flexural Strength ◽  
Tap Water ◽  
Splitting Tensile Strength ◽  
Content Type ◽  
Normal Water ◽  
Magnetic Water

PurposeThe influence of using magnetic water instead of tap water in the mechanical properties of the concrete exposed to elevated temperatures was investigated. Two concrete mixes were used and cast with the same ingredients. Tap water was used in the first mix and magnetic water was used in the second mix. A total of 48 specimens were cast and divided as follows: 16 cylinders for the concrete compressive strength test (8 samples for each mix), 16 cylinders for the splitting tensile strength (8 specimens for each mix) and 16 beams to test the influences of magnetized water on the flexural strength of concrete (8 specimens for each mixture). Specimens were exposed to temperatures of (25 °C, 200 °C, 400 °C and 600 °C). The experimental results showed that magnetic water highly affected the mechanical properties of concrete. Specimens cast and curried out with magnetic water show higher compressive strength, splitting tensile strength and flexural strength compared to normal water specimens at all temperatures. The relative strength range between the two types of water used was 110–123% for compressive strength and 110–133% for splitting strength. For the center point loading test, the relative flexural strength range was 118–140%. The use of magnetic water in mixing concrete contribute to a more complete hydration process.Design/methodology/approachExperimental study was carried out on two concrete mixes to investigate the effect of magnetic water. Mix#1 used normal water as the mixing water, and Mix#2 used magnetic water instead of normal water. After 28 days, all the samples were taken out of the tank and left to dry for seven days, then they were divided into different groups. Each group was exposed to a different temperature where it was placed in a large oven for two hours. Three different tests were carried out on the samples, these tests were concrete compressive strength, flexural strength and splitting tensile strength.FindingsExposure of concrete to high temperatures had a significant influence on concrete mechanical properties. Specimens prepared using magnetic water showed higher compressive strength at all temperature levels. The use of magnetic water in casting and curing concrete can increase the compressive strength by 23%. Specimens prepared using magnetic water show higher splitting tensile strength at all temperatures up to 33%. The use of magnetic water in casting and curing can strengthen and increase concrete resistance to high temperatures, a significant enhancement in flexural strength at all temperatures was found with a value up to 40%.Originality/valuePrevious research proved the advantages of using magnetic water for improving the mechanical properties of concrete under normal conditions. The potential of using magnetic water in the concrete industry in the future requires conducting extensive research to study the behavior of magnetized concrete under severe conditions to which concrete structures may be subjected to. These days, there are attempts to obtain stronger concrete with high resistance to harsh environmental conditions without adding new costly ingredients to its main mixture. No research has been carried out to investigate the effect of magnetic water on the mechanical properties of concrete exposed to elevated temperature. The main objective of this study is to evaluate the effect of using magnetic water on the mechanical properties of hardened concrete subjected to elevated temperature.

Research on Barite Concrete Mixed with Fly Ash

2013 ◽  
Vol 275-277 ◽  
pp. 2107-2111
Author(s):  
Qiu Lin Zou ◽  
Jun Li ◽  
Zhen Yu Lai
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Compressive Strength ◽  
High Temperature ◽  
Fly Ash ◽  
Apparent Density ◽  
Cycle Times ◽  
Residual Compressive Strength ◽  
Temperature Performance

Barite concrete with density grade of 3 and strength grade of C30 was prepared by mixing with different fineness of fly ash. The workability, mechanical properties and long-term high temperature performance of the prepared barite concrete were researched. Results show that the workability of barite concrete is improved by mixing with fly ash, and no segregation of mixture has been observed. The apparent density and 3d, 28d compressive strength of barite concrete are decreased obviously after mixing with fly ash. But with the increasing of the fineness of fly ash, the apparent density and 3d, 28d compressive strength of barite concrete have a slight increase. High temperature residual compressive strength is decreased with the increasing of temperature. The cycle times of heat treatment at 400°C only has a little effect on residual compressive strength of barite concrete.

scholarly journals Strength Characteristics of High Strength Concrete (HSC) with and without Coarse Aggregate

2019 ◽  
Vol 9 (2) ◽  
pp. 4701-4704
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
Fly Ash ◽  
Flexural Strength ◽  
Silica Fume ◽  
High Strength Concrete ◽  
Mechanical Characteristics ◽  
Coarse Aggregate ◽  
High Strength ◽  
Set Up

This paper aimed to investigate the mechanical characteristics of HSC of M60 concrete adding 25% of fly ash to cement and sand and percentage variations of silica fumes 0%,5% and 10% to cement with varying sizes of 10mm,6mm,2mm and powder of granite aggregate with w/c of 0.32. Specimens are tested for compressive strength using 10cm X 10cmX10cm cubes for 7,14,28 days flexural strength was determined by using 10cmX10cmX50cm beam specimens at 28 days and 15cm diameter and 30cm height cylinder specimens at 28 days using super plasticizers of conplast 430 as a water reducing agent. In this paper the experimental set up is made to study the mechanical properties of HSC with and without coarse aggregate with varying sizes as 10mm, 6mm, 2mm and powder. Similarly, the effect of silica fume on HSC by varying its percentages as 0%, 5% and 10% in the mix studied. For all mixes 25% extra fly ash has been added for cement and sand.

Effects of Fly Ash Addition on Compressive Strength and Flexural Strength of Foamed Cement Composites

2013 ◽  
Vol 795 ◽  
pp. 664-668 ◽  
Author(s):  
Roshasmawi Abdul Wahab ◽  
Mohd Noor Mazlee ◽  
Shamsul Baharin Jamaludin ◽  
Khairul Nizar Ismail
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
Fly Ash ◽  
Flexural Strength ◽  
Cement Composites ◽  
Volume Percent ◽  
Foaming Agent ◽  
Cement Ratio ◽  
Water To Cement Ratio

In this study, the mixing of polystyrene (PS) beads and fly ash as a sand replacement material in foamed cement composites (FCC) has been investigated. Specifically, the mechanical properties such as compressive strength and flexural strength were measured. Different proportions of fly ash were added in cement composites to replace the sand proportion at 3 wt. %, 6 wt. %, 9 wt. % and 12 wt. % respectively. The water to cement ratio was fixed at 0.65 meanwhile ratios of PS beads used was 0.25 volume percent of samples as a foaming agent. All samples at different mixed were cured at 7 and 28 days respectively. Based on the results of compressive strength, it was found that the compressive strength was increased with the increasing addition of fly ash. Meanwhile, flexural strength was decreased with the increasing addition of fly ash up to 9 wt. %. The foamed cement composites with 12 wt. % of fly ash produced the highest strength of compressive strength meanwhile 3 wt. % of fly ash produced the highest strength of flexural strength.

Performance of ilmenite concrete at sustained elevated temperatures

1988 ◽  
Vol 15 (5) ◽  
pp. 776-783
Author(s):  
H. S. Wilson
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
High Temperature ◽  
Flexural Strength ◽  
Key Words ◽  
Elevated Temperatures ◽  
Cement Ratio ◽  
Nondestructive Tests ◽  
High Temperature Mechanical Properties ◽  
Curing Period

Two similar mixes were made with cement contents of about 350 kg/m3 and a water–cement ratio of 0.50. The concrete specimens, moist cured for 7 days, were cured in air for 28 and 120 days, respectively, prior to heating. The exposure temperatures were 75, 150, 300, and 450 °C. The periods of exposure at each temperature were 2, 30, and 120 days.The compressive strengths, before heating, of the specimens cured for 35 and 120 days were 41.0 and 46.2 MPa, respectively, and the flexural strengths were 4.9 and 5.8 MPa. Compared with those strengths, the strengths of the specimens heated for 30 days or more increased at 75 °C but decreased at higher temperatures. The losses increased with increase in temperature, reaching about 30% at 450 °C.The flexural strength of the concrete cured in air for 28 days was more adversely affected than was the compressive strength. The flexural and compressive strengths of the concrete cured in air for 120 days were affected to about the same degree. The longer curing period had little effect on the relative losses in compressive strength, but the longer curing period reduced the loss in flexural strength. In most applications, the loss in strength could be compensated by proportioning the mix to overdesign for strength. Key words: high-density concrete, ilmenite, aggregates, high temperature, mechanical properties, nondestructive tests.

Influence of Variable Temperature Curing on Mechanical Properties of Fly Ash Concrete

2011 ◽  
Vol 250-253 ◽  
pp. 178-181
Author(s):  
Ya Ding Zhao ◽  
Xue Ying Li ◽  
Ling Chao Kong ◽  
Wei Du
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
Elastic Modulus ◽  
Fly Ash ◽  
Flexural Strength ◽  
Variable Temperature ◽  
Improve Performance ◽  
Curing Conditions ◽  
Fly Ash Concrete ◽  
Better Than

Under variable temperature curing conditions(30 oC ~70 oC), concrete with fly ash whose compressive strength, flexural strength, and dynamic elastic modulus are better than ones without fly ash.Compared with constant temperature 20oC, 50 oC and 70 oC, variable temperature curing(VTC) is benefit for the improvement of mechanical properties of 30% fly ash concrete, but which is no advantage to improve performance of 50% fly ash concrete.

scholarly journals Effect of fly ash on physical and mechanical properties of mortar

2019 ◽  
Vol 17 (6) ◽  
pp. 35
Author(s):  
Vu-An Tran
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
Fly Ash ◽  
Flexural Strength ◽  
Water Absorption ◽  
Thermal Power ◽  
Setting Time ◽  
Physical And Mechanical Properties ◽  
Flow Density ◽  
Control Specimen

This research investigates the physical and mechanical properties of mortar incorporating fly ash (FA), which is by-product of Duyen Hai thermal power plant. Six mixtures of mortar are produced with FA at level of 0%, 10%, 20%, 30%, 40%, and 50% (by volume) as cement replacement and at water-to-binder (W/B) of 0.5. The flow, density, compressive strength, flexural strength, and water absorption tests are made under relevant standard in this study. The results have shown that the higher FA content increases the flow of mortar but significantly decreases the density of mixtures. The water absorption and setting time increases as the samples incorporating FA. Compressive strength of specimen with 10% FA is approximately equal to control specimen at the 91-day age. The flexural strength of specimen ranges from 7.97 MPa to 8.94 MPa at the 91-day age with the best result for samples containing 10% and 20% FA.

scholarly journals Effect of Elevated Temperature on Alkali Activated Slag and Fly Ash based Geopolymer Concrete

2020 ◽  
Vol 9 (4) ◽  
pp. 1241-1250
Keyword(s):  
Compressive Strength ◽  
Elevated Temperature ◽  
Fly Ash ◽  
Flexural Strength ◽  
Portland Cement ◽  
Ordinary Portland Cement ◽  
Geopolymer Concrete ◽  
Base Materials ◽  
Activated Slag ◽  
Alkali Activated

Activated Slag (AAS) and Fly Ash (FA) based geopolymer concrete a new blended alkali-activated concrete that has been progressively studied over the past years because of its environmental benefits superior engineering properties. Geopolymer has many favorable characteristics in comparison to Ordinary Portland Cement. Many base materials could be utilized to make geopolymer with the convenient concentration of activator solution. In this study, the experimental program composed of two phases; phase on divided into four groups; Group one deliberated the effect of sodium hydroxide molarity and different curing condition on compressive strength. Group two studied the effect of alkali activated solution (NaOH and Na2SiO3) content on compressive strength and workability. The effect of sand replacement with slag on compressive strength and workability was explained in group three. Group four studied the effect of slag replacement with several base materials Fly Ash (FA), Ordinary Portland Cement (OPC), pulverized Red Brick (PRB), and Meta Kaolin (MK). Phase two contains three mixtures from phase one which had the highest compressive strength. For each mixture, the fresh concrete test was air content. In addition the hardened concrete tests were the compressive strength at 3, 7, 28, 90, 180, and 365 days, the flexural strength at 28, 90, and 365 days, and the young's modulus at 28, 90, and 365 days. Moreover; the three mixtures were exposed to elevated temperature at 100oC, 300oC, and 600oC to study the effect of elevated temperature on compressive and flexural strength.

Sign in / Sign up

Export Citation Format

Share Document